Tucker Barbecues Charcoal Deluxe Built In Montageanleitung

V29.04.2021

ASSEMBLY, INSTALLATION

AND OPERATING INSTRUCTIONS

CHARCOAL DELUXE BARBECUE

INSULATION JACKET

IMPORTANT – PLEASE READ ALL INSTRUCTIONS

BEFORE YOU ASSEMBLE, INSTALL OR

OPERATE THIS APPLIANCE.

IMPORTANT SAFETY INSTRUCTIONS

INSULATION JACKET ASSEMBLY INSTRUCTIONS

INSTALLATION INSTRUCTIONS & WARNINGS

DIMENSIONS

WARRANTY

CONTENTS

IMPORTANT SAFETY

INSTRUCTIONS

• Tucker Charcoal Deluxe Barbecues are

approved for outdoor use only.

• Remove all plastic protection lm from

stainless steel components before assembly.

• Keep this manual for future reference.

• Read all instructions carefully before

assembly and usage of barbecue/insulation

jacket.

• Clean your barbecue regularly; check the

grease trays for excess grease build up as

damage by grease or fat re is not covered

by warranty.

• Always check that the re has died off when

nishing barbecuing.

• A canvas cover for this barbecue will extend

its life and ensure trouble free operation.

• Attend an operating barbecue at all times.

• Do not use this appliance indoors or in any

enclosed area.

• Do not spray aerosols in the vicinity of this

appliance while it is in operation.

• Do not place articles on or against this

appliance.

WARNING FOR

YOUR SAFETY

• Placing to much charcoal in the barbecue

can result in a huge re that can damage

the BBQ and cause danger.

• Charcoal BBQs burn oxygen and release

carbon monoxide along with other harmful

gases that can kill or make you very sick, it

only takes a couple of hand lls of charcoal

burning in a small room to kill, make sure

you never use the BBQ indoors.

• The BBQ is very hot when it is in use, do not

use the BBQ up against or closer than 1m to

any combustible surfaces.

• It is advisable to place something non-

combustible such as pavers or tiles in front

of the BBQ just in case hot coals roll out by

accident when relling the re box.

• When looking for a place to set up your

Charcoal BBQ outside think about the

surroundings around it.

• Look for a safe place away from bushes

or overhanging trees or other possible re

hazards.

• Do not use or store ammable materials in or

near this appliance.

• Do not modify this appliance in any way.

• Do not allow children to operate the

barbecue.

• Always open the Lid or Roasting Hood before

lighting.

• Do not stack the charcoal up; a single layer

of charcoal will provide plenty of heat to

cook enough food for a standard family

meal.

HAZARDOUS FIRE OR EXPLOSION MAY

RESULT IF INSTRUCTIONS ARE IGNORED.

It is the consumer’s responsibility to see that the

barbecue is properly assembled, installed and

taken care of. Failure to follow the instructions in

this manual could result in serious bodily injury

and /or property damage.

INSULATION JACKET

ASSEMBLY INSTRUCTIONS

• Remove the pallet and any plastic lm protecting

or covering any parts of the Insulation Jacket.

• Cut away any packaging or cable ties that may

be holding components in place.

• Check you have all the correct components as

listed in this Page.

10mm spanner

Phillips head screwdriver

TOOLS REQUIRED FOR ASSEMBLY

INSULATION JACKET PARTS

1x Rear Back Panel Filler

1x Base Panel

1x Grease/Ash Tray Louvered Fascia

65mm x M6

Phillips Head Bolts

15mm x M6

Round Head Bolts

M6 Nuts

7mm Spacer

Washers

M4 Nuts

20mm x M4

Round Head Bolts

14x

15mm x M6

Phillips Head Bolts

Left Side

Panel

Left Rotisserie

Arm Hole Cover

Right Rotisserie

Arm Hole Cover

Right Side

Panel

1x Back Panel

Charcoal Deluxe Insulation Jacket

Assembly

1. Place the base panel onto your work surface with

the stainless steel side face down and remove

the foil insulation from the base panel.

2. Once the insulation is removed you can see

and access the 6 x holes that you need to use

to screw the 15mm phillips head bolts through to

attach the side panels to the base panel.

3. The next step is to attach the back panel to the

ends of the side panels, you will need to screw 2

x 15mm phillips head bolts with a 7mm spacer on

each bolt into the two holes in the back vertical

ends of each side panel.

The side panels have a small square notch

cut out which signies the front of the side

panels, the front of the base panel has 2 small

holes on the front edge which also signies the

front. When you attach the base panel to the

side panels, the base panel needs to have

the stainless steel side facing up and the side

panels have the insulation facing inward.

4. Now you can attach the back panel to the side

panels. Line up the bolt heads on the back of the

side panels with the key holes in each corner of

the back panel and push the back panel down

over the bolt heads which will locate the back

panel into position.

The top of the back panel should be ush with

the top of the side panels when it is in position

correctly.

5. The next step is to secure the back panel to

the base panel using a 15mm phillips head bolt

xed through the middle of the base panel and

through into the bottom of the back panel.

6. Now you can replace the insulation back into the

base panel.

7. The next step is to attach the rear ller panel

to the top of the back panel. You will need to

attach 3 x phillips head bolts and nuts with a

small 7mm spacer/ washer under the head of

the bolts to the rear ller panel as per the photo.

8. Now you are ready to attach the rear ller panel.

Line up the key hole slots on the rear panel with

the bolt heads on the back panel, now locate

them over the bolt heads and push the rear ller

panel down locking it into position.

10. Next take the ash/grease tray fascia and remove

the protective cover from the pins on each end

of it. Be careful not to lose the small spacer sitting

on the end of each pin.

11. Now locate the right hand side pin into the hole

in the front of the right hand side panel.

12. Now using a phillips head screwdriver loosen the

two phillips head bolts on the back side of the

left hand side of the fascia panel.

By loosening these two bolts it allows the locating

pin on the left hand side of the fascia panel to

slide backwards enough so that you can easily

slide the fascia panel into position and then slide

it back again locating the pin into the hole on

the left hand side panel and then tighten it back

up to lock it in position.

9. Next is the attachment of the grease / ash tray

fascia to the front of the insulation jacket, before

you do this, using the 2 x 20mm bolts and nuts ,

screw one into each side of the base panel at

the front of the jacket.

These bolts are used for adjusting the position the

fascia panel stops at, screwing them in or out will

change the position the fascia sits vertically.

13. Now behind the grease /ash tray fascia you can

adjust the position the fascia sits into the jacket

vertically by using the two bolts and nuts you

installed earlier. Simply screw the bolts in or out

and once you are happy with the position the

fascia sits, simply tighten the nut.

15. Remove the grease /ash tray from the BBQ and

lower the BBQ into the jacket.

To secure the BBQ into the Insulation Jacket use

the 8 x 65mm bolts and push them through the

four holes on either side of the Insulation Jacket

side panels.

You need to line the ends of the bolts up to the

nuts that are welded into the side panels of the

BBQ. Once you have them all lined up start to

tighten the bolts rotating the tightening around

the sides of the jacket a little bit on each bolt at

a time.

14. The Insulation Jacket is now complete and ready

for the charcoal deluxe BBQ to be inserted into.

16. The last thing to do is to slide the grease/ash tray

back into the BBQ.

The grease / ash tray has an adjustable height

front fascia on it, which is helpful over time as

the heat from the ash will cause the tray to

expand and contract.

The adjustment bolts allow you change the

height of the fascia so as to help make sliding

the tray in and out easier.

To adjust the height simply loosen the bolts

move the fascia by hand and then tighten the

bolts back up again.

Do not use a drill to tighten any nuts and bolts

together in the Insulation Jacket assembly.

Using a drill to tighten them together makes

them hot and will cause them to bind on

each other and get stuck.

Inhaltsverzeichnis

Andere Tucker Barbecues Küchengerät Handbücher

Tucker Barbecues

Tucker Barbecues GTR Series Montageanleitung

Beliebte Küchengerät Handbücher anderer Marken

Tayama

Tayama TYG-35AF Bedienungsanleitung

AEG

AEG 43172V-MN Bedienungsanleitung

REBER

REBER Professional 40 Benutzerhandbuch

North American

North American BB12482G / TR-F-04-B-NCT-1 Bedienungsanleitung

Presto

Presto fountain popper Bedienungsanleitung

Westmark

Westmark 1035 2260 Bedienungsanleitung

Zanussi

Zanussi ZCG64396XA Bedienungsanleitung

HOFFEN

HOFFEN SM-9302M Bedienungsanleitung

Philips

Philips HD3133 Bedienungsanleitung

Ronco

Ronco Beef Jerky Bedienungsanleitung

Hendi

Hendi 470411 Bedienungsanleitung

Livoo

Livoo MEN386 Bedienungsanleitung

croydon

croydon WR-10313-700 Bedienungsanleitung

Chefman

Chefman RJ43-SQ Series Bedienungsanleitung

Vacmaster

Vacmaster VP680 Bedienungsanleitung

Jetmaster

Jetmaster 900HG Bedienungsanleitung

Küppersbusch

Küppersbusch EEH 610.0 Kurzanleitung zur Einrichtung

HURAKAN

HURAKAN HKN-F10 Bedienungsanleitung