Turbonics T45 Bedienungsanleitung

TWMIOM-2

Installation:

• Toester Wall-Mount hydronic fan coils are suitable for

connection to a hot water supply at any pressure up to 300

psi with a maximum water temperature of 200°F.

• Building codes and plumbing regulations may vary.

Check local codes and regulations before determining

proper application and installation.

• Examine unit for shipping damage.

55mm

188mm

432mm

14 17

369mm

T68-WM

INLET 1/2"

COPPER TUBING

OUTLET 1/2"

COPPER TUBING

WIRING INPUT

18 3

462mm

321

93mm

14 1

362mm

T45-WM

CAT-09852-TUR

Figure 1 - T45/T68-WM-Top View

• Unit is designed to be mounted under or over sheetrock.

Install at least 6" - 8" above the oor for best performance.

Unit will t between standard 16" studs on center.

• For unit dimensions on the T45/T68 refer to Figure 1, 3, 6

& 7. For T13 refer to Figure 2, 4, 8 & 9.

• Secure unit in proper position. Unit must be level to assure

proper drainage and operation.

Toester Wall-Mount Fan Coil

Installation Instructions

Model T45/68/13 All Sizes

14 9

370mm

21 13

554mm

584mm

14 9

362mm

18mm

28mm

INLET 1/2"

COPPER TUBING

OUTLET 1/2"

COPPER TUBING

CAT-09853-TUR

T13-WM

Figure 2 - T13-WM-Top View

Piping

• e piping on the unit will usually be copper or any other

locally approved piping. Accessible ½" sweat ttings are

provided on the unit itself. An optional exible stainless

steel connector kit with shut-o valves is available for

connecting the unit to any type of piping system and can

be used with an optional valve control box.

• All piping systems should be designed by a technician

with experience in the various piping arrangements that

work with this type of unit.

• As with any system employing circulated water, the pipes

passing through unheated spaces should be insulated.

NOTE: When using mono-ﬂo or “venturi" ﬁttings, we

suggest placement of a ball valve just after the supply

take-oﬀ and before the return is connected.

Piping: Hot Water Boiler

• e unit supply line should be taken from the boiler side

beyond any o-control valve. If the system being used

is a gravity-ow or cast iron hot water system, a separate

circuit must be installed.

Piping: Water Heater

• To install correctly, a technician with knowledge of piping

arrangements and back-o valves must design the piping

system.

Wiring the Unit

• A eld wiring connection is provided on the unit (see

Figure 5). Connect wires at this point only.

• e unit is manufactured with a built-in factory wired

aquastat with a set point of 140°F on and 110°F o. e

aquastat may be disabled in the eld if not required (see

application manuals).

T45/68-WM

RECESSED

COVER

T45/68-WM

SURFACE MOUNT

COVER

T45/68-WM

UNIT

4X #10-32 X 1/2" SCREW

AND NYLON WASHER

(INCLUDED)

CAT-09852-TUR

T45/68-WM

RECESSED

COVER

T45/68-WM

SURFACE MOUNT

COVER

T45/68-WM

UNIT

4X #10-32 X 1/2" SCREW

AND NYLON WASHER

(INCLUDED)

CAT-09852-TUR

4X #10-32 X 1/2" SCREW

AND NYLON WASHER

(INCLUDED)

T13-WM

SURFACE MOUNT

COVER

T13-WM

RECESSED

COVER

T13-WM

UNIT

CAT-09853-TUR

4X #10-32 X 1/2" SCREW

AND NYLON WASHER

(INCLUDED)

T13-WM

SURFACE MOUNT

COVER

T13-WM

RECESSED

COVER

T13-WM

UNIT

CAT-09853-TUR

Figure 3 - T45/68-WM

Figure 4 - T13-WM

Figure 5 - Wiring Diagram T45-WM/T68-WM / T13-WM

TUR-09867C

2-SPEED

2P MOTOR

CONTROL BOX

2-SPEED

2P MOTOR

CONTROL BOX

FACTORY WIRED; LO SPEED

2-SPEED

2P MOTOR

CONTROL BOX

OPTIONAL FACTORY WIRED; 2 SPEED SWITCH OPTIONAL FIELD WIRED; 2-SPEED SWITCH INSTALLATION

OFF

WHITE

BLACK

RED (LO)

BLACK (HI)

BLUE

BLACK

FIELD BLACK

TO SWITCH

COMMON

RED (LO)

FROM SWITCH

BLACK (HI)

FROM SWITCH

WHITE

BLACK

RED (LO)

BLACK (HI)

WHITE

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLACK

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

SEE NOTE 3

NOTES:

1. FOR USE WITH MODELS:

T12-HA, T45-HA, T68-HA, T13-WM-AR, T13-WM-AS, T45-WM-AR,

T45-WM-AS, T68-WM-AR, T68-WM-AS, K-J SERIES.

2. ALL WIRING SHALL MEET ALL LOCAL AND NATIONAL CODE.

3. "A" TO DIRECT WIRE ON HIGH SPEED REPLACE RED (LO) WIRE

CONNECTION TO BLUE AQUASTAT WIRE WITH BLACK (HI) WIRE. CAP

THE DISCONNECTED RED (LO) WIRE BEFORE POWERING THE UNIT.

4. "A" TO DIRECT WIRE ON HIGH SPEED REPLACE RED (LO) WIRE

CONNECTION TO YELLOW AQUASTAT WIRE WITH BLACK (HI) WIRE.

CAP THE DISCONNECTED RED (LO) WIRE BEFORE POWERING THE

UNIT.

5. T13-WM-AR & T13-WM-AS BLUE WIRE FROM MOTOR CAPPED BY

BLUE

AQUASTAT

WHITE

BLACK

RED (LO)

BLACK (HI)

WHITE

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLACK

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLUE

AQUASTAT

2-SPEED

SWITCH

FOR USE WITH MODELS: T13-WM-AR, T13-WM-AS, T45-WM-AR, T45-WM-AS, T68-WM-AR, T68-WM-AS ONLY

2-SPEED

2P MOTOR

CONTROL BOX

2-SPEED

2P MOTOR

CONTROL BOX

FACTORY WIRED; LO SPEED

2-SPEED

2P MOTOR

CONTROL BOX

OPTIONAL FACTORY WIRED; 2 SPEED SWITCH

OPTIONAL FIELD WIRED; 2-SPEED SWITCH INSTALLATION

OFF

WHITE

BLACK

RED (LO)

BLACK (HI)

BLUE

BLACK

FIELD BLACK

TO SWITCH

COMMON

RED (LO)

FROM SWITCH

BLACK (HI)

FROM SWITCH

WHITE

BLACK

RED (LO)

BLACK (HI)

WHITE

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLACK

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

SEE NOTE 3

NOTES:

1. FOR USE WITH MODELS:

T12-HA, T45-HA, T68-HA, T13-WM-AR, T13-WM-AS, T45-WM-AR,

T45-WM-AS, T68-WM-AR, T68-WM-AS, K-J SERIES.

2. ALL WIRING SHALL MEET ALL LOCAL AND NATIONAL CODE.

3. "A" TO DIRECT WIRE ON HIGH SPEED REPLACE RED (LO) WIRE

CONNECTION TO BLUE AQUASTAT WIRE WITH BLACK (HI) WIRE. CAP

THE DISCONNECTED RED (LO) WIRE BEFORE POWERING THE UNIT.

4. "A" TO DIRECT WIRE ON HIGH SPEED REPLACE RED (LO) WIRE

CONNECTION TO YELLOW AQUASTAT WIRE WITH BLACK (HI) WIRE.

CAP THE DISCONNECTED RED (LO) WIRE BEFORE POWERING THE

UNIT.

5. T13-WM-AR & T13-WM-AS BLUE WIRE FROM MOTOR CAPPED BY

BLUE

AQUASTAT

WHITE

BLACK

RED (LO)

BLACK (HI)

WHITE

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLACK

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLUE

AQUASTAT

2-SPEED

SWITCH

FOR USE WITH MODELS: T13-WM-AR, T13-WM-AS, T45-WM-AR, T45-WM-AS, T68-WM-AR, T68-WM-AS ONLY

2-SPEED

2P MOTOR

CONTROL BOX

2-SPEED

2P MOTOR

CONTROL BOX

FACTORY WIRED; LO SPEED

2-SPEED

2P MOTOR

CONTROL BOX

OPTIONAL FACTORY WIRED; 2 SPEED SWITCH OPTIONAL FIELD WIRED; 2-SPEED SWITCH INSTALLATION

OFF

WHITE

BLACK

RED (LO)

BLACK (HI)

BLUE

BLACK

FIELD BLACK

TO SWITCH

COMMON

RED (LO)

FROM SWITCH

BLACK (HI)

FROM SWITCH

WHITE

BLACK

RED (LO)

BLACK (HI)

WHITE

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLACK

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

SEE NOTE 3

NOTES:

1. FOR USE WITH MODELS:

T12-HA, T45-HA, T68-HA, T13-WM-AR, T13-WM-AS, T45-WM-AR,

T45-WM-AS, T68-WM-AR, T68-WM-AS, K-J SERIES.

2. ALL WIRING SHALL MEET ALL LOCAL AND NATIONAL CODE.

3. "A" TO DIRECT WIRE ON HIGH SPEED REPLACE RED (LO) WIRE

CONNECTION TO BLUE AQUASTAT WIRE WITH BLACK (HI) WIRE. CA

THE DISCONNECTED RED (LO) WIRE BEFORE POWERING THE UNIT.

4. "A" TO DIRECT WIRE ON HIGH SPEED REPLACE RED (LO) WIRE

CONNECTION TO YELLOW AQUASTAT WIRE WITH BLACK (HI) WIRE.

CAP THE DISCONNECTED RED (LO) WIRE BEFORE POWERING THE

UNIT.

5. T13-WM-AR & T13-WM-AS BLUE WIRE FROM MOTOR CAPPED BY

BLUE

AQUASTAT

WHITE

BLACK

RED (LO)

BLACK (HI)

WHITE

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLACK

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLUE

AQUASTAT

2-SPEED

SWITCH

FOR USE WITH MODELS: T13-WM-AR, T13-WM-AS, T45-WM-AR, T45-WM-AS, T68-WM-AR, T68-WM-AS ONLY

2-SPEED

2P MOTOR

CONTROL BOX

2-SPEED

2P MOTOR

CONTROL BOX

FACTORY WIRED; LO SPEED

2-SPEED

2P MOTOR

CONTROL BOX

OPTIONAL FACTORY WIRED; 2 SPEED SWITCH OPTIONAL FIELD WIRED; 2-SPEED SWITCH INSTALLATION

OFF

WHITE

BLACK

RED (LO)

BLACK (HI)

BLUE

BLACK

FIELD BLACK

TO SWITCH

COMMON

RED (LO)

FROM SWITCH

BLACK (HI)

FROM SWITCH

WHITE

BLACK

RED (LO)

BLACK (HI)

WHITE

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLACK

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

SEE NOTE 3

NOTES:

1. FOR USE WITH MODELS:

T12-HA, T45-HA, T68-HA, T13-WM-AR, T13-WM-AS, T45-WM-AR,

T45-WM-AS, T68-WM-AR, T68-WM-AS, K-J SERIES.

2. ALL WIRING SHALL MEET ALL LOCAL AND NATIONAL CODE.

3. "A" TO DIRECT WIRE ON HIGH SPEED REPLACE RED (LO) WIRE

CONNECTION TO BLUE AQUASTAT WIRE WITH BLACK (HI) WIRE. CAP

THE DISCONNECTED RED (LO) WIRE BEFORE POWERING THE UNIT.

4. "A" TO DIRECT WIRE ON HIGH SPEED REPLACE RED (LO) WIRE

CONNECTION TO YELLOW AQUASTAT WIRE WITH BLACK (HI) WIRE.

CAP THE DISCONNECTED RED (LO) WIRE BEFORE POWERING THE

UNIT.

5. T13-WM-AR & T13-WM-AS BLUE WIRE FROM MOTOR CAPPED BY

BLUE

AQUASTAT

WHITE

BLACK

RED (LO)

BLACK (HI)

WHITE

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLACK

FUSED FIELD

115VAC 60Hz

(FROM FAN CONTROL)

BLUE

AQUASTAT

2-SPEED

SWITCH

FOR USE WITH MODELS: T13-WM-AR, T13-WM-AS, T45-WM-AR, T45-WM-AS, T68-WM-AR, T68-WM-AS ONLY

.50

.375

1.11

1.25

4.56 2.50

19.50

.75

16.75

9.66

1.08

11 LOUVERS

21 LOUVERS

SECTION A-A

65°

.37

DETAIL B

SCALE 1 : 2

-001 (COVER, WALL MOUNT, T45-WM & T68-WM, RECESSED) SHOWN

Figure 6 - T45-WM & T68-WM Recessed

TUR-10169

19.88

.375

1.44

1.05

.50

4.56 2.50

-002 (COVER, WALL MOUNT, T45-WM & T68-WM, SURFACE) SHOWN

4.50

16.63

.63 .125

2X RSW

.38

.39

1.00

12.78

8 LOUVERS

14 LOUVERS

SECTION C-C

.37

65°

DETAIL D

SCALE 1 : 2

Figure 7 - T45-WM & T68-WM Surface Mount

TUR-10169

3.00 2.50

1.38

1.13

.375

.50

24.56

1.75

7.93

15.78

15 LOUVERS

11 LOUVERS

18 LOUVERS

SECTION A-A

16.81

.75 .37

65°

DETAIL B

SCALE 1 : 2

-001 (COVER, WALL MOUNT, T13-WM, RECESSED) SHOWN

Figure 8 - T13-WM Recessed

TUR-10170

260 NORTH ELM STREET, WESTFIELD, MA 01085

1.04

1.17

.375

3.00

.50

2.50

24.00

16.63

4.25 .63 .125

2X RSW

1.00

.44

.50

14.79

25 LOUVERS

20 LOUVERS

SECTION C-C

.37

65°

DETAIL D

SCALE 1 : 2

-002 (COVER, WALL MOUNT, T13-WM, SURFACE) SHOWN

Figure 9 - T13-WM Surface Mount

TUR-10170

Dieses Handbuch passt für folgende Modelle

Andere Turbonics Heizung Handbücher

Turbonics

Turbonics KWM6 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung