Tuxedo TP9KACX Bedienungsanleitung

Jun 2017

TP9KACX / TP9KSCX

Two-Post Clear Floor Lifts

(Asymmetric / Symmetric)

9,000 lbs. Capacity

(2,250 lbs. Max per Arm)

INSTALLATION & OPERATION

MANUAL

２

TP9KACX / TP9KSCX

Jan 2017

IMPORTANT NOTES

READ THE INSTALLATION AND OPERATION MANUAL IN ITS ENTIRETY BEFORE

ATTEMPTING TO INSTALL THE LIFT.

•Do not install this lift on any surface other than concrete, conforming to minimum specifications.

•Do not install this lift over expansion joints or cracks. Check with building architect.

•Do not install this lift on a second floor with a basement beneath without written authorization from

building architect.

•Do not install this lift outdoors unless special consideration has been made to protect the power unit

from inclement weather conditions.

•A level floor is recommended for proper installation and operation. Concrete should be a minimum

of 4-1/4” thickness and 3,000 psi tensile strength with steal or fiber mesh reinforcement.

•The lift is intended to raise the entire body of the vehicle. Do not attempt to lift only part of the vehicle.

Improper use of this equipment could result in damage to the lift, yourself or other property.

•The lift is intended to lift vehicles only. It is not designed to lift any person or equipment containing

persons.

•Users of this equipment should be qualified, responsible and should follow the operation and safety

guidelines set forth in this manual.

•For specifications on concrete pads, please call for technical assistance.

•Improper installation can cause damage or injury. The Manufacturer will NOTassume liability for loss

or damage of any kind, expressed or implied, resulting from improper installation or use of this

product.

DEFINITION

Surface Mounted, Two-Post, Clear-Floor Lift w/ Overhead Beam, Hydraulic ‘chain-over’ Drive,

9,000 lbs. Capacity.

The name / model numbers are designated below:

•Model number TP9KACX - Asymmetric Swing Arms configuration

•Model number TP9KSCX - Symmetric Swing Arms configuration

BASIC SPECIFICATIONS

Model Description

(Clear Floor)

Capacity Lifting Time Overall

Height

Overall

Width

Lifting

height

Between

Posts

TP9KACX

Asymmetric 9,000 lbs. 50 Sec 143” 138” 72” 113-5/8”

TP9KSCX

Symmetric 9,000 lbs. 50 Sec 143” 138” 72” 113-5/8”

３

TP9KACX / TP9KSCX

Jan 2017

PREPARATION

The installation of this lift is relatively simple and can be accomplished by 2 men in a few hours. The

following tools and equipment are needed:

•12 quarts of Non-Detergent / Non-Foaming Hydraulic Oil - SAE-10, AW 32 or equivalent

•Chalk line and 12’ Tape Measure

•4ft. Level

•Rotary Hammer Drill with 3/4” Masonry Drill Bit. (Core Drill Rebar Cutter also recommended)

•Hammer and Hex Key Wrench Set

•Metric Sockets and Open Wrench set - 13mm-30mm

•Medium Adjustable Wrench and Medium Pipe Wrench

•Crow Bar for Shim Installation and Medium Flat Screwdriver

•Locking, Needle Nose and Snap Ring Pliers

GENERAL INFORMATION

1. Carefully remove the crating and packing materials.

CAUTION! Be careful when cutting steel banding material as items may become loose and fall

causing personal harm or injury.

2. Identify the components and check for damage or shortages.

Please contact your distributor immediately, if any damages or shortages are discovered.

Packing:

•The lift assembly is packaged into two columns as one piece, as shown in (Fig.1).

•Every column comes with its cylinder, carriage, cables & chains, lifting arms, swivel pads, height

extensions, hoses and overhead beam with the hardware box located in one of the columns.

•

The electric-hydraulic motor pump is packaged separately and banded to top of lift.

Fig. 1

４

TP9KACX / TP9KSCX

Jan 2017

５

TP9KACX / TP9KSCX

Jan 2017

INSTALLATION INSTRUCTIONS

STEP 1: (Selecting Site) Before installing your new lift, check the following:

1. LIFT LOCATION: Always use architects plans when available. Check layout dimension against floor

plan requirements making sure that adequate space is available (Fig. 2, 2a, 2b & Fig. 3).

Fig. 2

(TP9KACX & TP9KSCX)

６

TP9KACX / TP9KSCX

Jan 2017

Fig. 2a

(TP9KACX - Asymmetric Lift)

Fig. 2b

(TP9KSCX - Symmetric Lift)

７

TP9KACX / TP9KSCX

Jan 2017

Fig. 3

(Column / Floor Layout)

2. OVERHEAD OBSTRUCTIONS: The area where the lift is located should be free of overhead

obstructions such as heaters, building supports, electrical lines, etc. (Fig 2.)

3. DEFECTIVE CONCRETE: Visually inspect the site where the lifts will be installed and check for

cracked or defective concrete. (Details on Page 4)

4. FLOOR REQUIREMENTS: The lift should be installed on a 3000 PSI concrete with minimum of 4-1/4”

thickness. The Floor should be level with-in gradients of ≦1/4” within area of the two columns = 138”

x 18”).

(See Details for Foundation Anchoring Requirements & Anchoring Tips on Page 4)

STEP 2: (Unloading & Unpacking)

1. After unloading the lift, place it near the intended installation location.

2. Remove the shipping bands and packing materials from the unit.

3. Remove the packing brackets and bolts holding the two columns together. (Do not discard bolts, they

may be used in the assembly of the lift)

4. Take out the lifting arms, swivel pads, height extensions, hardware box, hoses, covers, etc., from the

column. Check the quantity of each item with the parts list. If anything is missing, please contact your

dealer at once.

８

TP9KACX / TP9KSCX

Jan 2017

STEP 3: (Site Layout)

1. Determine which side will be the approach side.

2. Now determine which side you prefer the power unit to be located on. The

MAIN column has the power-unit mounting bracket attached to the side, as

shown in (Fig. 4).

Note: the power unit column can be located on either side. It is helpful

to try and locate the power side on the driver side of the vehicle when

loaded on the lift, in order to save steps during operation.

3. Once a location is determined, use a carpenter’s chalk line to layout a grid

for the post locations. (See Fig. 3)

Fig. 4

4. After the post locations are marked, use a chalk or crayon to make an outline of the posts on the floor

at each location using the post base plates as a template.

5. Double check all dimensions and make sure that the layout is perfectly square.

STEP 4: (Installing MAIN COLUMN w/ Power Unit Bracket)

1. Before proceeding, double check measurements and make certain that the bases of each column are

square and aligned with the chalk line.

2. Ensure Top Cap is pre-installed to the top of the Main column. Raise the column to a vertical position.

3. Using the base plate on the MAIN column as a guide, drill each anchor hole into concrete using a

rotary hammer drill and

” concrete drill-bit. To assure full holding power, do not ream the hole or

allow the drill to wobble. (See Anchoring Details on Page 4)

4. After drilling, remove dust thoroughly from each hole using compressed air and/or wire brush. Make

certain that the column remains aligned with the chalk line during this process.

Assemble the washers and nuts on the anchors then tap into each hole with a block of wood or rubber

hammer until the washerrests against the base plate. Be sure that if shimming

is required that enough threads are left exposed.

6. Using a level, check column plumb for every side (Fig. 5). If shimming is

required, use supplied Shim stock or 3/4” washers, placing shims as close

as possible to the hole locations. This will prevent bending column bases.

7. With the shims and anchor bolts in place, tighten by securing the nut to

the base then turning 2-3 full turns clockwise. Ensure anchor bolts are

tightened to a minimum of 130 ft-lbs. of torque. DO NOT use an impact

wrench for this procedure.

Fig. 5

９

TP9KACX / TP9KSCX

Jan 2017

STEP 5: (Installing OFFSIDE COLUMN & OVERHEAD BEAM ASSEMBLY)

NOTE: Install Overhead Beam assembly to top of columns BEFORE drilling anchors for Offside

column. This is to ensure that the Offside column can be properly positioned to be plumb and

level.

1. Raise OFFSIDE column and position at the designated chalk locations, ensuring the

Top Cap is pre-

installed to the top of the OFFSIDE column.

2. Assemble and mount the Overhead ‘padded’ Shut-Off Bar & Limit Switch assembly to the Overhead

Beam, as shown below in (Fig 6).

NOTE: Ensure to position the Limit Switch Box assembly on the same side as the Power Unit.

Fig. 6

3. Using a lifting device, raise the Overhead Beam assembly and position on top of the columns. Bolt it

to the columns using the bolts, nuts and washers, as shown in (Fig. 6).

4. Use a tape measure to measure the diagonal distance between the opposite corners of the base plates

on the columns. Equal values will ensure the lifting arms will be in square.

5. Secure OFFSIDE column to the floor following the same procedures as outlined in STEP 4.

Overhead Limit Switch Box

must be positioned on

same side as Power Unit

１０

TP9KACX / TP9KSCX

Jan 2017

STEP 6: (Installing POWER UNIT)

1. Attach the power unit to the mount bracket on the side of the Main

Column using bolts, nuts and washers supplied (Fig. 7).

2. Remove the vent plug from the power unit and fill the reservoir with

hydraulic oil. Make sure the funnel used to fill the power unit is

clean.

Suggestion: Use Non-Detergent / Non-Foaming Hydraulic Oil - SAE-10,

AW 32 or equivalent. The unit holds approximately ten

quarts of fluid.

Fig. 7

STEP 7: (Installing / Routing EQUALIZER CABLES)

1. Raise and lock each carriage on the first

safety latch engagement, approximately 30”

high.

2. Make sure that the safety locks on each

column are fully engaged before attempting

to route equalizer cables.

3. Be sure each carriage is at the same height

by measuring from the top of the base to the

bottom of the carriage. This difference

should be within 1/4”.

4. Route the first cable. (See Figs 8 & 9)

Screw the nut on the cable stud so that half

thread pass through the nut. Pull the other

end of the cable and screw the nut on it

also. Then tighten both nuts.

Fig. 8 Fig. 9 (Cable Route Diagram

)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tuxedo Hebesystem Handbücher

Tuxedo

Tuxedo FP8K-DS Bedienungsanleitung

Tuxedo

Tuxedo FP8K-DS Bedienungsanleitung

Tuxedo

Tuxedo M-1500C-HR Bedienungsanleitung

Tuxedo

Tuxedo TP12KFX Bedienungsanleitung

Tuxedo

Tuxedo M-1000C Betriebsanleitung

Tuxedo

Tuxedo LR-26-PAD Stücklistenhandbuch

Tuxedo

Tuxedo FP14KO-A Beilage

Tuxedo

Tuxedo MR6K-38 Bedienungsanleitung

Tuxedo

Tuxedo TP9KF Stücklistenhandbuch

Tuxedo

Tuxedo TP9KAC-TUX Bedienungsanleitung

Tuxedo

Tuxedo TP11KC-DX Bedienungsanleitung

Tuxedo

Tuxedo FP12K-K Stücklistenhandbuch

Tuxedo

Tuxedo FP14K Bedienungsanleitung

Tuxedo

Tuxedo JMC9KAC-TUX Bedienungsanleitung

Tuxedo

Tuxedo FP8K-B Montageanleitung

Tuxedo

Tuxedo M-1500C-HR Gebrauchsanweisung

Tuxedo

Tuxedo PL6K Bedienungsanleitung

Tuxedo

Tuxedo TP9KF-TUX Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung