TW Audio VERA RF600 Bedienungsanleitung
Assembly
Instructions
VERA RF600
Assembly Instructions VERA RF600
2
Introduction
Thank you for choosing a high-quality product “MADEIN GERMANY” from TW AUDiO.
The VERA RF600 rigging frame is an accessory for the VERA20 and VERA S32 loudspeakers.
It is characterized by a subtle look, a remarkable size to weight ratio and ease of use.
If you lend your product to another party, inform that party of the safety-related operating pro-
cedures and hand over this operating manual. If you require additional copies of this manual,
you can obtain them free of charge from TW AUDiO or download them from: www.twaudio.de
Instructions in this setup manual
Strictly adhere to the instructions contained in this assembly guide that are marked as follows:
This symbol in combination with the signal word “Caution” identifies a potentially hazardous
situation. Failure to comply with this safety instruction can lead to light or moderate injury.
This symbol in combination with the signal word “Note” identifies a potentially hazardous situa-
tion. Failure to comply with this safety instruction can lead to product damage.
This symbol in combination with the signal word “Tip” identifies additional information or notes
that will simplify working with TW AUDiO products on the basis of practical experience.
This symbol in combination with the signal word “Warning” identifies a potentially hazardous
situation. Failure to comply with this safety instruction can lead to serious injury or even death.
NOTE
TIP
CAUTION
WARNING
Assembly Instructions VERA RF600
3
Notes on the products
Read manual
before use!
Before using the rigging frame, carefully read the assembly instructions and keep the instruc-
tions in a safe place together with the VERA RF600 rigging frame.
General Information
Assembly Guide: OM-VERA RF600
Version 1.0 d, 06/2018
© by TW AUDiO 2018; all rights reserved.
All information contained in this assembly guide was correct to the best of our knowledge at
the time of printing.
Quality warranties or assurance of suitability for a certain type of use based on the technical
specifications, dimensions and weights are not granted by TWAUDiO.
TW AUDiO also shall not assume liability for any secondary damage (property damage and/or
personal injury) nor for the failure to comply with this assembly guide!
TW AUDiO reserves the right to update this document based on recent developments.
TW AUDiO GmbH
Osterholzallee 140-1
71636 Ludwigsburg
Phone: +49 7141 488989-0
Fax: +49 7141 488989-99
Assembly Instructions VERA RF600
4
Table of contents
1. Safety | Intended use........................................................................................................6
2. Overview...........................................................................................................................8
2.1. Scope of delivery....................................................................................................8
2.2 Placement of accessories for storage on the VERA RF600......................................9
3. Technical specifications.....................................................................................................9
3.1 Data sheet..............................................................................................................9
4. Commissioning...............................................................................................................10
4.1. Setup....................................................................................................................10
4.2. Preparing the VERAORF900 outrigger set............................................................10
4.3. Assembly (rear): VERAORF900 outrigger attached to VERA RF600 rigging frame..11
4.4. Assembly (front): VERAORF900 outrigger attached to VERA RF600 rigging frame 12
4.5. Ground.................................................................................................................13
4.6. Alignment..............................................................................................................14
4.6.1. Step 1: front alignment...................................................................................14
4.6.2. Step 2: rear alignment....................................................................................14
4.6.3. Step 3: side alignment...................................................................................14
4.7. Pitfalls...................................................................................................................15
4.8. Danger of tipping over...........................................................................................15
4.9. Wind load..............................................................................................................15
4.10. Groundstack of the lowest VERA20 speaker.........................................................16
4.11. VERA20 groundstack setup, from the second speaker..........................................19
4.12. VERAS32 groundstack setup...............................................................................23
4.13. VERAS32 groundstack setup, from the second speaker.......................................27
4.14. Mixed VERAS32 and VERA20 groundstack setup................................................30
4.15. Preparing of VERA20 for rigging............................................................................33
4.16. Using the VERALA900 load adapter in flown system.............................................35
4.17. Secondary safety component in the flown system.................................................37
4.18. Wind load in the flown system...............................................................................38
4.19. Flown system setup with VERA20 loudspeakers...................................................39
Assembly Instructions VERA RF600
5
4.20. Flown system setup with VERA20 loudspeakers, from the second speaker set.....45
4.21. Flown system setup with VERAS32 loudspeakers................................................53
4.22. Flown system setup with VERAS32 loudspeakers, from the second speaker........56
4.23. Flown mixed system setup with VERA20 and VERAS32 loudspeakers.................62
4.24. DE-Rigging a flown system with VERA20 loudspeakers.........................................68
4.25. DE-Rigging a flown system with VERAS32 loudspeakers.....................................81
4.26. DE-Rigging a flown mixed system with VERA20 and VERAS32 loudspeakers......87
5. Transport and Storage....................................................................................................90
6. EC - Declaration of Conformity........................................................................................91
7. Disposal..........................................................................................................................91
Assembly Instructions VERA RF600
6
1. Safety | Intended use
To avoid risks please observe the following safety instructions when using accessories.
The VERA RF600 rigging frame was developed for use in professional sound systems. The rigging
frame may only be used by trained and qualified personnel.
Damage caused by improper use is not covered by TW AUDiO.
Before each installation, check the integrity of the VERARF600 rigging frame and ensure that all
components are in perfect condition.
The scope of delivery includes a specified load adapter with shackle. Only use this load adapter.
WARNING
The VERA RF600 rigging frame may only be used with the VERA20 and VERA S32 loudspeakers.
These assembly instructions describe how to use the VERA RF600 rigging frame. Any other use
shall be deemed improper and may result in damage or even injury.
Modifications or alterations to individual parts of the VERA RF600 rigging frame and the VERA LA900
load adapter are not permitted! Danger to life!
WARNING
During and after each system setup, check that all quick-lock pins are always completely inserted!
All quick-lock pins must always be used!
WARNING
The VERA RF600 is an accessory designed both for indoor and outdoor use.
CAUTION
The VERA RF600 rigging frame may only be used by trained and qualified personnel. Personnel
must check the VERA RF600 for its full suitability before each use.
WARNING
When visible damage to any part of the VERARF600 rigging frame is detected, it must be decom-
missioned immediately.
WARNING
Before mounting the VERARF600 rigging frame, all attachment points – such as ceilings and cross-
beams – must be checked for full load capacity and stability.
The VERARF600 accessory is specified for a load of not more than 24 (twenty-four) VERA20
loudspeakers or twelve (12) VERAS32 loudspeakers. This load capacity must never be exceeded!
WARNING
Assembly Instructions VERA RF600
7
When moving (assembling, dismantling, maintaining) the VERARF600 rigging frame with
VERA20 or VERA S32 loudspeakers, ensure sufficient space to prevent collisions with other
objects.
WARNING
When working with heavy loads exceeding 20 kg (44,09 lbs.), use suitable aids (dollies, hoisting
slings, etc.). Multiple persons may be required depending on the situation.
NOTE
When installing the VERA RF600 rigging frame, be careful not to pinch or twist the power cables
or other cables attached to the VERA20 or VERAS32 loudspeakers! The respective national
electrotechnical regulations apply.
CAUTION
All screw connections should be checked each time the VERARF600 rigging frame is installed.
Tighten all loose screws. If this is no longer possible, the screws must be replaced.
WARNING
Assembly Instructions VERA RF600
8
1. VERA RF600 rigging frame – powder-coated surface
2. Load adapter with VERA LA900 shackle
3. Captive quick-lock pins
2. Overview
2.1 Scope of delivery
When the VERA RF600 rigging frame is delivered from the factory, the load adapter with the
VERA LA900 shackle and the quick-lock pins are in “Storage Position”.
NOTE
Figure 2.1 – Overview
1
3
3
3
3
2
Assembly Instructions VERA RF600
9
3. Technical specifications
2.2 Placement of accessories for storage on the VERA RF600
1. Outrigger VERA ORF900 for use with the VERA RF600 as a ground frame
2. Space for additional VERA LA900 load adapter
3. Angle sensor set VERA LAS900
Figure 2.2 - Overview
For storage, first insert all quick-lock pins through the mounting holes of the VERAORF900 out-
rigger set and then through the mounting holes on the VERARF600 rigging frame.
Make sure that each outrigger is securely attached to the VERA RF600 rigging frame.
WARNING
3.1 Data sheet
1
1
2
3
Assembly Instructions VERA RF600
10
1. Outrigger
2. Spindle foot
3. Quick-lock Pin
4. Commissioning
4.1 Setup
The VERA ORF900 consists of four outriggers with spindle feet and quick-lock pins.
Screw all spindle feet of the VERAORF900 outrigger set to the position indicated in figure 4.2.
NOTE
Figure 4.2 – ORF900 Outrigger
The VERA RF600 rigging frame is designed both for standing and hanging operation. TW AUDiO
provides a wide range of accessories to securely attach the rigging frame to crossbeams, motor
lifts, etc. in a suspended position.
TW AUDiO recommends using only the accessories specified by TW AUDiO for securing and moun-
ting the rigging frame.
NOTE
4.2 Preparing the VERAORF900 outrigger set
60
1 2
3
A B C
Inhaltsverzeichnis
Andere TW Audio Lautsprechersystem Handbücher
Beliebte Lautsprechersystem Handbücher anderer Marken
Sondpex
Sondpex Active Speaker System and Digital Music... Bedienungsanleitung
JVC
JVC NX-PN7 Bedienungsanleitung
Marshall Amplification
Marshall Amplification AR-DM61-BT Bedienungsanleitung
Yamaha
Yamaha NX-A01 - Speaker Sys Bedienungsanleitung
SE Audiotechnik
SE Audiotechnik I-LINE Bedienungsanleitung
Gemini
Gemini WRX-843 Series Bedienungsanleitung