Twodots Harrier Bedienungsanleitung

INSTRUCTION

LIMITATION OF LIABILITY

• The drone is not a toy and it is designed for users above 14 years of age.

• The product integrates several control technologies. However, improper use may cause injuries to people or

material damage. Read the related manual and documents before use.

• The information in this manual concerns the users’ safety and responsibility. Read the full manual carefully

to ensure that the product is configured appropriately before use. Failure to read and/or comply with the

instructions may cause injuries to the user or other people, material damage and loss of the product.

• We recommend flying the drone only in the authorized areas where no prohibitions apply.

• Do not use the drone when under the influence of alcohol or drugs.

• X-Joy Srl shall not be liable for the use and the operations performed with the drone nor for any damage

and/or injuries or legal liability directly or indirectly attributable to the use of the product.

• The pilot is the only liable person for any actions and possible accidents and shall have to comply with safe

and legitimate conduct rules.

WARNING

• Stay away from rotating propellers and from the engines.

• Ensure that the flight area is free from any encumbrances and that the drone flies at a distance of at least

two meters from the user and other people.

• Ensure that no other drones are flying with the same frequency.

• Never lose sight of the drone while flying.

• Flight range is about 500mt: never let the drone go further than that distance or the signal might lose

intensity and the user might be unable to control the drone.

• Remove the batteries from the drone and the controller if they are not used.

• Do not overcharge the batteries.

• Charge the battery in a clean and dry place, far from any flammable objects, heat sources and direct

sunlight.

• Do not leave the batteries unguarded while charging them.

• Never use any batteries that have not been authorized by Twodot.

• Do not open the drone and/or the batteries.

• In case of fluid leaks and subsequent eye contact, go to the hospital immediately.

• Never touch the drone engines during flight or immediately after landing.

• Never touch the propellers when they are moving.

• Stop using the drone immediately if it is damaged.

• Always dispose of any parts of the drone and of the controller pursuant to the regulations in force.

• Do not expose the drone battery to heat sources, high temperatures or flames.

• Before flying, make sure that the batteries of the drone and of the controller are fully charged.

• Check that the drone battery and propellers are assembled and fixed appropriately. Incorrect assembly may

affect the flight performance.

SAFETY RULES

• Please, pay attention to the safety rules and read about liability in case of damage to people or things.

• Keep a safe distance from people during flight since the drone is a dangerous device.

• Incorrect assembly, damaged body, faulty electronic components and improper use may cause accidental

damage to the drone and to people.

• For your safety, it is recommended not to use the drone in case of rain, storm, thunders/lighting and strong

wind.

• Avoid humid environments.

• Please use the drone according to your physical abilities and control skills. Fatigue, distraction and, in

Propeller B

Front

Rear

On/off

Camera

Battery

Propeller A

Propeller B

Drone upper

housing

Propeller A

Front LED

(Green)

Front LED

(Green)

Memory Card Slot

Drone Bottom Housing

Rear LED

(rosso)

Rear LED

(rosso)

Top cover

RightLeft

• general, improper use increase the likelihood of accidents.

• Keep away from the rotating parts. The rotating parts may cause serious damage and injuries. Keep face

and body away from the rotating parts and the engines.

• Do not expose to heat sources. The drone is made of metal parts, fibres, plastic, electronic parts, etc. Do

not expose the drone to heat sources and direct sunlight to prevent the risk of deformations and damage.

• Do not touch the engine while it is hot to prevent the risk of burns.

PRELIMINARY CHECKS

• The flight area must be large enough. We recommend an area of at least 8 meters in length and 5 meters

in height.

• Ensure that the drone batteries are fully charged.

• Please comply with the procedures to switch your drone on/off. Switch on the controller first and then

the drone. When your flight is finished, switch off the drone first and then the controller. Failure to comply

with the procedure may cause you to lose control of the drone with subsequent risks for people and things.

Please memorize and follow the correct procedure to turn the device on and off.

• Check the connections between battery, engine, etc. Vibrations may cause power disconnection and the

subsequent loss of the drone.

• Improper use may make the drone fall, thus causing damage to the engine, noise, stability loss and even

impossibility to fly.

• The drone must fly within the action range of the control system. Avoid flying close to tall buildings, high-

voltage cables and other places which may interfere with the control signal. If the signal is lost, the drone is

out of control and it may cause damage to people and things.

DRONE FUNCTIONS

CONTROLLER FUNCTIONS

INSERTING THE BATTERIES INTO THE CONTROLLER

Open the battery compartment and insert four AA batteries (not included). Make sure you place them in the

right direction according to their polarity, as shown on the controller.

INSTALLING THE BATTERY

Place the battery inside the compartment in the back of the drone and check that it is installed correctly by

pressing the battery down until it is fully inside and fixed.

InterruttoreInterruttore

Phone holder slot

GimbalPhoto/Video

Right stick

Left stick

Return Home button One button take off/landing

Trimmer mode

button

Hi/Medium/Low speed

(press)

Attivazione GPS

(keep pressed)

Battery cover

4x alkaline

batteries 1.5V

Battery closure

Sticker upwards

CHARGING THE DRONE BATTERY

ASSEMBLY OF THE PROPELLERS

Remove the battery from the drone. Put the battery in the charger and connect the power supply to a power

source through the provided USB cable.

The red LED light shows that the battery is being charged, the green LED shows that the battery is fully charged.

Charging time is about 280 minutes and the average flight time is about 14 minutes, however this may vary

depending on certain external agents like temperature, humidity, wind, etc.

You can use a max 5V USB adapter to charge the controller and the drone battery

Do not charge the batteries immediately after use. Let them cool down first.

Do not put the battery close to any heat sources and high temperatures and do not throw it in the fire.

The first time you use it, you will need to mount the propellers before proceeding with the flight.

Make sure you mount the propellers in the correct position according to the picture below:

• Left front propeller shown with letter A

• Right front propeller shown with letter B

• Left back propeller shown with letter B

• Right back propeller shown with letter A

Position the propeller, insert the silicone washer and use the metal cap to tighten the propeller.

For propellers marked with the letter A, use retainers with a concave surface.

For propellers marked with the letter B, use the flat-surface fasteners.

Drone battery

Phone charger Power bank Computer Car charger

Turn on the remote control, move the left

stick first up and then down. The red LED

will start blinking slowly.

Place the drone on a flat surface and press

the power button for 2 seconds.

The pairing procedure is then completed.

PAIRING

Place the drone

on a flat surface.

CALIBRATING THE COMPASS

You need to calibrate the compass before the flight to make it easier and more stable.

Complete the pairing procedure. After the procedure, only the LED lights on the left of the drone will remain lit.

Flip the drone horizontally until the controller beeps. Then, flip the drone vertically (with the camera facing

upwards) until the controller beeps.

PLEASE NOTE: pcalibrate the compass before each flight in a new area.

WARNING

• Do not calibrate the drone close to magnetic fields or metallic structures.

• It is not required to calibrate the compass if you fly the drone several times consecutively in the same area.

• If flight is not very stable in GPS mode, you need to calibrate the compass again following the procedure

above.

GPS MODE

After the proper setting, the drone automatically activates the GPS tracking signal. When reception is sufficient

you will hear an acoustic signal and the LEDs on the drone as well as the blue LED will remain steady.

PLEASE NOTE: When no GPS connection, the drone can only fly within three meters.

WARNING

• A precise and strong GPS signal depends on several factors, like the presence of interferences or not.

• Electricity pylons, antennas and high-tension wires may affect the precision of the GPS and of the compass.

• When the GPS is activated, use the drone outdoors only.

• Minimize any possible interference by avoiding areas characterised by high levels of electromagnetism,

including towers and bases for radio transmissions.

Level correction Vertical correction

RESET PROCESS

CONTROL

Read the following instructions carefully and do not try to fly the drone before acquiring good skills in controlling

the vehicle.

Place the drone in an open, flat space, free from any encumbrances. Position yourself behind the drone and turn

so that you are headed in the same direction as the drone. The green LED lights indicate the front and the red

LED light indicate the back of the device.

TAKE-OFF

To activate the engines, push both sticks on the controller down and inwards.

The engines will start running.

Move the left stick up and down to lift the drone to the desired height or press the button for automatic take-off

for a second and the drone will automatically lift to above 1.2 metres.

Gently move the left stick upwards to increase the drone’s height. Thanks to the “Auto-Hovering” function, the

drone will autonomously maintain the desired height without you having to act on the accelerator continuously.

LANDING

Move the left stick downwards to land the drone. Keep the left stick down for 2-3 seconds until the engines

stop or press the automatic landing button for a second. The drone will start landing from the position it is in.

Do not move the left stick during the automatic landing phase – otherwise the automatic landing phase will be

interrupted.

PLEASE NOTE: if the drone is in an emergency, you can immediately stop the engines. To do so, start the same

procedure you use to activate the engines.

Before flying or in case of need following bumps or

falls, the gyroscopes on the drone will have to be

reset.

Place the drone on a flat surface and move

the right stick to the lower right corner for few

seconds.

The drone’s LEDs will blink.

The process is completed when the LEDs blink

normally.

FLIGHT CONTROLS

When the throttle stick

is moved left, the drone

will rotate to the left. When the directional

stick is moved left, the

drone will fly to the left

side.

LEFT

STICK

When the throttle stick

is moved right, the drone

will rotate to the right. When the directional

stick is moved right, the

drone will fly to the right

side.

When the throttle stick

is pushed up, the blades

will spin faster causing

the drone to ascend. When the directional

stick is moved up, the

drone will fly forward.

When the directional

stick is moved down, the

drone will fly backward.

When the throttle stick

is pushed down, the

blades will spin slower

causing the drone to

descend.

RIGHT

STICK

GIMBAL

SPEED REGULATION

This drone can fly at three different speeds.

When you press the Speed switch on the controller (button on th

back right), you will hear a double beep and speed will pass to

intermediate. By pressing it again, you will hear three beeps and

speed will be high.

Press the Speed selector one more time to return to low speed.

PHOTOS AND VIDEOS

Hi/Medium/

Low speed mode

button

You can use the remote control to record videos and take photographs

by simply pressing the button on the left.

By pressing the dedicated button, the controller will beep to signal the

beginning of recording/photo shooting.

Press once to take a picture, press and hold for one second to start

recording a video. Press again to stop recording.

WARNING

• When you start to record a video you must stop recording by pressing the dedicated button before you land

the device and remove the drone battery. Otherwise, the video will not be saved on the memory card.

• Put a micro SD memory card (not included) into the dedicated slot to record a video or take a photo.

Photos will be saved on a memory card and on the device memory (if you are using a smartphone), while videos

will be saved on the memory card.

However, you can download or view the video on your smartphone when it is connected via Wi-Fi.

Put your memory card into your computer to view the saved photos and videos.

With Harrier you can change the inclination of the camera by the

one-axis gimbal.

To move the camera during flight, press and hold the button on

the remote control until you reach the desired position.

RETURN TO HOME

This feature allows you to allow the drone to approach the pilot by

pressing the dedicated button.

When you launch the Return to Home function, the drone cannot

avoid the obstacles along its route.

To abandon this mode, press the corresponding button again.

Once the drone reaches its destination, it will land automatically.

WARNING

• Pay attention to any possible obstacles or interferences along

the way.

• The Return to Home function shall be activated automatically if

the GPS signal is not strong enough and the battery level is low.

FOLLOW ME

ORBIT MODE

You can activate the Follow Me function when the drone is in flight

by pressing the left stick in the centre. A beep will tell you that the

mode is active.

Thanks to the GPS signal, the drone can follow the user.

WARNING

This function can only be activated if the smartphone is connected with

a Wi-Fi network, if satellite access is active and the GPS signal is strong enough for both devices.

ORBIT MODE

Press

Turn left, the drone flies

clockwise; Move further, the

fllying speed will become faster.

Turn right, the drone flies

counterclockwise; Move further,

the speed will become faster.

Go downside to enlarge the

radius of encircling.

Go upward to narrow the

radius of encircling.

When the Orbit function

is activated the left stick

could only control

the height of the drone.

Press

When the Orbit function is activated, the drone will fly automatically in a circle around its position.

Push the right stick towards the centre to activate the function. A beep will tell you that the mode is active.

The drone will automatically fly at the set height and radius. Pay attention to any possible obstacles or

interferences along the way. Use the right stick to control the circle direction, the flight speed and the circle

radius as detailed in the following picture.

Inhaltsverzeichnis

Andere Twodots Drohne Handbücher

Twodots

Twodots TVVIN BOARD Bedienungsanleitung

Beliebte Drohne Handbücher anderer Marken

Ryze

Ryze Tello Bedienungsanleitung

PowerVision

PowerVision PowerRay Bedienungsanleitung

Force1

Force1 rogue F72 Bedienungsanleitung

Zerotech

Zerotech DOBBY Bedienungsanleitung

Protocol

Protocol VIDEODRONE AP Bedienungsanleitung

dji

dji Matrice M210 Bedienungsanleitung

SYMA

SYMA X440 Bedienungsanleitung

SYMA

SYMA X5UW(720P) Bedienungsanleitung

Dynali

Dynali 25 H Leitfaden

dji

dji PHANTOM 4 Bedienungsanleitung

Atlas

Atlas AtlasPRO Bedienungsanleitung

GDU

GDU SAGA Bedienungsanleitung

RUKO

RUKO F11 Bedienungsanleitung

Ares

Ares ETHOS QX 130 Bedienungsanleitung

Walkera

Walkera ZHUN Bedienungsanleitung

dji

dji WIND-4 Bedienungsanleitung

Potensic

Potensic D58 Bedienungsanleitung

Arris

Arris M900 Bedienungsanleitung