TYAN NETSCALIBUR Bedienungsanleitung
No part of this manual may be reproduced, transmitted, or stored in any media
form or by any means without the written permission of Tyan Computer
Corporation. Copyright (C) 1996-7 by Tyan Computer Corporation. All Rights
Reserved. The information in this manual is subject to change without notice.
V1.2
Netscalibur is a trademark of Tyan Computer Corporation.
Windows 95 and Windows NT are trademarks of Microsoft Corporation.
Pentium is a trademark of Intel Corporation.
Internet Explorer is a trademark of Microsoft Corporation.
Navigator is a trademark of Netscape Communications Corporation.
Any other trademarks are hereby acknowledged.
Quick Start .................................................................................. 2
What is the Netscalibur .............................................................. 3
Inside the Box ............................................................................. 3
System Requirements ................................................................. 4
Cable Connection ........................................................................ 4
On-Line Browser Manual ................................................................... 5
ISDNDiagnosticTool.................................................................6
Windows95Installation.............................................................8
UninstalltheDrivers.................................................................12
Windows NT 4.0 Installation .................................................... 13
InstallDial-UpNetworking.................................................................13
InstallRemoteAccessService.............................................................16
Install Internet Explorer and ISDN Diagnostic Tool ........................ 17
Windows NT 3.51 Installation .................................................. 18
WindowsNT3.51addendum.....................................................20
FCCComplianceStatement......................................................21
2
Windows 95 User
Power off the system and insert the Netscalibur Card.
Boot to Windows 95 and select "Do not install a driver (Windows
will not prompt you again)."
Insert the Netcalibur CD and click on the SETUP option.
Install the modem drivers, ISDN acceleration pack, ISDN
diagnostic tool, and Internet Explorer. Add TCP/IP protocol and
Dial-Up Adapter in the Network applet. Next, restart the system.
Select "Disk provided by hardware manufacturer" and browse to
the Netscalibur CD's \driver\isdn directory.
Select Netscalibur ISDN-ISA PNP and enter the correct switch
type, ISDN phone numbers, and SPID numbers.
Stop! Read the instructions carefully.
Caution
Please take note here.
Please follow this direction.
How to read the signs
Windows NT 4.0 User
In the Control Panel, run the Network applet. Remove the
Remote Access Services (RAS) before installing the Netscalibur
drivers.
In the Adapter folder, select Add and click on the Have Disk
button. Enter the \driver\isdn directory of the Netscalibur CD.
Choose an IRQ, address, and switch type. Select Multi-Point and
enter the SPID numbers with a space between the numbers.
Next, select 64000 bps and enter the ISDN phone numbers with
a space between the numbers (do not include the area code).
Add ISDN1-Netscalibur and ISDN2-Netscalibur ISDN channels
and TCP/IP protocol. Finally, restart the system.
1
2
3
4
1
2
3
4
5
6
3
It offers 128Kbps speed through a reliable digital
connection, thus increasing productivity.
It supports fast 33.6Kbps analog modem connectivity with a
standard phone line.
It runs HTML, VRML, Java, Java scripts, & Active X faster
than a 28.8Kbps modem.
It has an easy installation setup and offers an on-line
browser manual for troubleshooting and acquiring the latest
drivers and product information.
It is perfect for intranet, internet phone, internet browsing,
video conferencing, remote LAN access, and telecommuting
for individuals, small businesses, and corporate enterprises.
ISDN and 33.6K modem connections can be used
simultaneously.
v
v
v
v
v
v
qq 1 Netscalibur Internet Accelerator Card
qq 1 Installation Guide
qq 1 Setup CD
qq 1 RJ-45 to RJ-11 ISDN cable
qq 1 RJ-11 to RJ-11 modem cable
4
Your system should have the following:
qq Intel Pentium 75Mhz (120Mhz recommended) or Pentium Pro
qq Windows 95 or Windows NT 4.0 or 3.51
qq Motherboard with at least 256K external cache
qq 8MB of DRAM (16MB recommended)
qq CD-ROM drive
qq Sound Card (Wavetable recommended)
(RJ-45 or RJ-11)
(RJ-11)
If the phone company installs a RJ-45 phone
jack instead of the regular RJ-11 phone jack
for the ISDN line, you can still plug a RJ-11
connector into a RJ-45 phone jack. You can
also request that the phone company install
the RJ-11 phone jack for your ISDN line.
5
click on me
Use the browser manual to get the latest update on drivers and
product information.
Netscalibur also comes with an easy-to-use browser manual. The
On-Line browser manual is an extension of the printed manual.
You can launch the browser manual by double-clicking the
Netscalibur icon and then selecting the Browser Manual.
Make sure you install Internet Explorer or Navigator before
launching the browser manual.
Netscalibur's browser manual offers
links to technical support and answers
to many frequently asked questions.
Moreover, the browser manual also
comes with an unique video technical
support feature to help you install the
Netscalibur and serve as a quick guide
for surfing the internet. Just click on
the Netscalibur castle to access the
video clips.
6
ISDN signaling layers
B Channel Activity
First B Channel or
Second B Channel
The Netscalibur comes with a Virtual LEDs program to help
you diagnose your ISDN hardware and ISDN lines. The setup
program will place the diagnostic tool in the startup group for
easy access. This diagnostic program enables you to verify that
the Netscalibur's ISDN is functioning properly by checking the
ISDN signaling layer lights. If all three signaling layer lights turn
green, it means that the ISDN driver is loaded properly and the
ISDN phone line is synchronized. Occasionally, one of the L3
lights will take longer turning green then the other lights. It may
take up 30 seconds for the line to synchronized with the
telephone company.
For everyday usage, you will find the following information
useful.
L1,L2, and L3 lights turn grey color:
This means that the Netscalibur card is not in your system.
L1,L2, and L3 lights turn green color:
This means that the ISDN is working properly and the driver has
loaded successfully. Normally, this is a good indication that the
Netscalibur card, cable, and the ISDN lines are functioning
properly. However, it does not guarantee that the SPID and
phone numbers are entered correctly.
7
L1, L2, and L3 lights turn red:
This means that the driver is not loaded. For Windows 95 users,
first check the Netscalibur's network properties in the Device
Manager for resources conflicts. An interrupt or IO address
conflict will prevent the driver from loading. You can access the
Device Manager by moving the mouse cursor to My Computer
follow by clicking on the right mouse button to bring out the
properties sheet. Afterwards, click on properties to go to
System Properties and then select Device Manager folder. Go
down to network adapters and double-click on Netscalibur
ISDN ISA-PnP to check Resources for conflicts. For Windows
NT users, you should bring up the Windows NT diagnostic in
Administrative tools to check for resource conflicts.
The red lights may also be caused by a bad cable or cable
connection. Check the ISDN RJ-45 to the phone jack and make
sure they are properly inserted.
L1 lights turn green but L2 and L3 remain red: This is
normal if the phone company uses Point-to-Point protocol. The
light will turn green once the connection has been established.
Otherwise, it means that the driver is loaded but the switch type,
SPID numbers, or the phone numbers for ISDN are incorrect.
First check the switch type, SPID numbers, and phone numbers
in the Start -> Programs -> Accessories -> ISDN tools -> ISDN
Configuration Wizard. Make sure you enter the correct SPID
numbers, phone numbers, and switch type. This information is
supplied by the phone company. If you do not know the switch
type, please select AUTO instead.
Ch1 and Ch2 remain red:
This is normal. The B Channel Activity light will turn green
only after the connection has been established. Otherwise, they
will remain red. If Ch1 turns green but Ch2 remains red, it
means that only channel 1 is connected.
The ISDN diagnostic tool does not work under
Windows NT 3.51. It will work under Windows
95 and Windows 4.0.
8
95
3. Perform a Scandisk operation before installing the drivers.
The setup program needs to modify the registry data and
copy files to your hard disk. Scanning the hard disk for
corrupted files will enable the setup program to copy drivers
correctly to the hard disk. The ScanDisk program is located
in Start -> Programs -> Accessories -> System Tools.
If you accidentally select "Disk provided by
manufacturer." then you should do an uninstall as
described in page 6 before continuing with the setup in
step 12.
1.
2.
Power off the system and insert the Netscalibur into an
empty 16-bit ISA slot and remove other modem cards from
the system. Afterwards, power on the system and boot to
Windows 95.
You must install the ISDN accelerator pack v1.1 or above
before installing Netscalibur's ISDN driver. Therefore,
before you install the Microsoft ISDN Accelerator Pack
from the Netscalibur Wizard CD, choose "Do not install a
driver (Windows will not prompt you again)" when
Windows 95 detects the Netscalibur or choose "Cancel" if
you have Windows 95 OEM services release 2 .
9
4. Insert the Netscalibur CD into the CD-ROM drive. The
Netscalibur Wizard should auto-start or you can double click
on the Netscalibur CD-ROM icon to launch the
Netscalibur Wizard.
If your CD-ROM drive does not perform auto-run or
double-clicking the Netscalibur icon does not bring up
the Netscalibur Wizard, then you can run the setup
program by selecting Open from the file menu.
Afterwards, double-click sword.exe to run the setup.
5. Click on the Installation Video Clip to watch the setup
video clip first before running Setup. The video clip will
show the entire installation process and help you get a better
idea of the installation procedures. The setup process may
vary slightly between different program version.
After finishing watch the setup video clip, click on the Setup
option to install the drivers and ISDN software. You must
install the following software by selecting Yes or No and
then clicking on the Continue button to go to the next step.
Please read the instructions on the monitor carefully. In
addition, please do not restart the system until you
configure the Dial-Up Networking in Part C. You can skip
Part A if you do not wish to install the modem or skip Part B
if you do not wish to install the ISDN. However, Part C is
required for internet access.
6.
10
Part A
Install Modem
Drivers
Part B
Install ISDN Acceleration
Pack and
ISDN Diagnostic Tool
During the setup procedure, please wait for Windows
95 to finish updating the shortcuts before going to the
next step. This step may take a couple of minutes.
Do not restart the system after Part B.
Part C
Install Dial-up Adapter
and TCP/IP Protocol
Inhaltsverzeichnis
Andere TYAN Computerhardware Handbücher
TYAN
TYAN GC79A-B7132 Kurzanleitung
TYAN
TYAN FA100-B7118 Bedienungsanleitung
TYAN
TYAN S5567 Bedienungsanleitung
TYAN
TYAN M3291 Bedienungsanleitung
TYAN
TYAN TS65-B7120 Kurzanleitung
TYAN
TYAN GT20A-B7040 Kurzanleitung
TYAN
TYAN M3291 Installationsanleitung
TYAN
TYAN S5393 Bedienungsanleitung
TYAN
TYAN Transport GT24 Kurzanleitung
TYAN
TYAN GC68A-B8056 Kurzanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
