TYAN FT48B-B7100 Kurzanleitung

http://www.tyan.com

FT48B-B7100

Service Engineer’s Manual

http://www.tyan.com

PREFACE

This publication, including all photographs, illustrations, and software, is

Neither this manual, nor any material contained herein, may be reproduced

without written consent of manufacturer.

rights reserved. TYAN®is a registered trademark of MITAC COMPUTING

TECHNOLOGY CORPORATION.

Version 1.0a

Disclaimer

Information contained in this document is furnished by MITAC COMPUTING

TECHNOLOGY CORPORATION and has been reviewed for accuracy and

reliability prior to printing. MITAC assumes no liability whatsoever, and

disclaims any express or implied warranty, relating to sale and/or use of TYAN®

products including liability or warranties relating to fitness for a particular

purpose or merchantability. MITAC retains the right to make changes to

produce descriptions and/or specifications at any time, without notice. In no

event will MITAC be held liable for any direct or indirect, incidental or

consequential damage, loss of use, loss of data or other malady resulting from

errors or inaccuracies of information contained in this document.

Trademark Recognition

All registered and unregistered trademarks and company names contained in

this manual are property of their respective owners including, but not limited to

the following.

TYAN®is a trademark of MITAC COMPUTING TECHNOLOGY

CORPORATION.

Intel®is a trademark of Intel®Corporation.

AMI®, AMIBIOS® and combinations thereof are trademarks of AMI

Technologies.

Microsoft®, Windows®are trademarks of Microsoft Corporation.

IBM®, PC®, AT®and PS/2®are trademarks of IBM Corporation.

Winbond®is a trademark of Winbond Electronics Corporation.

http://www.tyan.com

FCC Declaration

Notice for the US

Compliance Information Statement (Declaration of

Conformity Procedure) DoC FCC Part 15: This

device complies with part 15 of the FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following conditions:

This device may not cause harmful interference.

This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Notice for Canada

This Class A digital apparatus complies with Canadian ICES-003. Cet

appareil numérique de la Classe A est conforme à la norme NMB-003 du

Canada.

Notice for Europe (CE Mark)

This product is in conformity with the Council

Directive 2014/30/EU.

Warning: This equipment is compliant with Class A of CISPR 32. In a

residential environment this equipment may cause radio interference.

CAUTION: Lithium battery included with this board. Do not puncture,

mutilate, or dispose of battery in fire. There will be danger of explosion if

battery is incorrectly replaced. Replace only with the same or equivalent

type recommended by manufacturer. Dispose of used battery according to

manufacturer instructions and in accordance with your local regulations.

この装置は、クラスＡ情報技術装置です。この装置を家庭環境で使用すると電波妨

害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要

求されることがあります。

ＶＣＣＩ－Ａ

http://www.tyan.com

About this Manual

This manual is intended for trained service technician/personnel with hardware

knowledge of computers. Front bezel key should be controlled by trained service

technician/personnel. Components inside the compartments should be serviced only

by a trained service technician/personnel. This manual is aimed to provide you with

instructions on installing your TYAN FT48B-B7100.

How this guide is organized

This guide contains the following parts:

Chapter 1: Overview

This chapter provides an introduction to the TYAN FT48B-B7100 barebones and

standard parts list, describes the external components, gives an overview of the

product from different angles.

Chapter 2: Setting Up

This chapter covers procedures on installing the processors, memory modules, hard

drivers and other optional parts.

Chapter 3: Replacing the Pre-installed Components

This chapter covers the removal and replacement procedures for pre-installed

components.

Appendix:

This chapter provides the cable connection table, the FRU parts list for reference of

system setup, and technical support in case a problem arises with your system.

http://www.tyan.com

Safety and Compliance Information

Before installing and using TYAN FT48B-B7100, take note of the following

precautions:

·Read all instructions carefully.

·Do not place the unit on an unstable surface, cart, or stand.

·Do not block the slots and opening on the unit, which are provided for

ventilation.

·Only use the power source indicated on the marking label. If you are not

sure, contact the power company.

·The unit uses a three-wire ground cable, which is equipped with a third pin to

ground the unit and prevent electric shock. Do not defeat the purpose of this

pin. If your outlet does not support this kind of plug, contact your electrician

to replace your obsolete outlet.

·Do not place anything on the power cord. Place the power cord where it will

not be in the way of foot traffic.

·Follow all warnings and cautions in this manual and on the unit case.

·Do not push objects in the ventilation slots as they may touch high voltage

components and result in shock and damage to the components.

·When replacing parts, ensure that you use parts specified by the

manufacturer.

·When service or repairs have been done, perform routine safety checks to

verify that the system is operating correctly.

·Avoid using the system near water, in direct sunlight, or near a heating

device.

·Cover the unit when not in use.

http://www.tyan.com

Safety Information

Retain and follow all product safety and operating instructions provided

with your equipment. In the event of a conflict between the instructions in

this guide and the instructions in equipment documentation, follow the

guidelines in the equipment documentation.

Observe all warnings on the product and in the operating instructions. To

reduce the risk of bodily injury, electric shock, fire and damage to the

equipment, observe all precautions included in this guide.

You must become familiar with the safety information in this guide before

you install, operate, or service TYAN products.

Symbols on Equipment

Caution. This symbol indicates a potential hazard.

The potential for injury exists if cautions are not

observed. Consult equipment documentation for

specific details.

Caution. Slide-mounted equipment is not to be

used as a shelf or a work space.

Warning. This symbol indicates the presence of

hazardous energy circuits or electric shock

hazards. Refer all servicing to qualified personnel.

Warning. This symbol indicates the presence of a

hot surface or hot component. If this surface is

contacted, the potential for injury exists.

To reduce risk of injury from a hot component,

allow the surface to cool before touching.

General Precautions

· Follow all caution and warning instructions marked on the equipment and

explained in the accompanying equipment documentation.



Machine Room Environment

· This device is for use only in a machine room or IT room.

 · Make sure that the area in which you install the system is properly

ventilated and climate-controlled.

http://www.tyan.com

· Ensure that the voltage and frequency of your power source match the

voltage and frequency inscribed on the electrical rating label of the

equipment.

·Do not install the system in or near a plenum, air duct, radiator, or heat

·Never use the product in a wet location.

Equipment Chassis

· Do not block or cover the openings to the system.

·Never push objects of any kind through openings in the equipment.

Dangerous voltages might be present.

·Conductive foreign objects can produce a short circuit and cause fire,

electric shock, or damage to your equipment.

·Lift equipment using both hands and with your knees bent.

Equipment Racks

To avoid injury or damage to the equipment:

·Observe local occupational health and safety requirements and guidelines

for manual materials handling.

·Do not attempt to move a rack by yourself; a minimum of two people are

needed to move a rack.

·Do not attempt to move a fully loaded rack. Remove equipment from the

rack before moving it.

·Do not attempt to move a rack on an incline that is greater than 10 degrees

from the horizontal.

·Make sure the rack is properly secured to the floor or ceiling.

·Make sure the stabilizing feet are attached to the rack if it is a single-rack

installation.

·Make sure racks are coupled together if it is a multiple-rack installation.

·Make sure the rack is level and stable before installing an appliance in the

rack.

·Make sure the leveling jacks are extended to the floor.

http://www.tyan.com

·Make sure the full weight of the rack rests on the leveling jacks.

·Always load the rack from the bottom up. Load the heaviest component in

the rack first.

·Make sure the rack is level and stable before pulling a component out of the

rack.

·Make sure only one component is extended at a time. A rack might become

unstable if more than one component is extended.

To avoid damage to the equipment:

· The rack width and depth must allow for proper serviceability and cable

management.

· Ensure that there is adequate airflow in the rack. Improper installation or

restricted airflow can damage the equipment.

·The rack cannot have solid or restricted airflow doors. You must use a

mesh door on the front and back of the rack or remove the doors to ensure

adequate air flow to the system.

·If you install the Model in a rack, do not place equipment on top of the unit.

It will cause restricted airflow and might cause damage to the equipment.

·Make sure the product is properly matted with the rails. Products that are

improperly matted with the rails might be unstable.

·Verify that the AC power supply branch circuit that provides power to the

rack is not overloaded. This will reduce the risk of personal injury, fire, or

damage to the equipment. The total rack load should not exceed 80 percent

of the branch circuit rating. Consult the electrical authority having jurisdiction

over your facility wiring and installation requirements.

Equipment Power Cords

· Use only the power cords and power supply units provided with your

system. The system might have one or more power cords.

·Plug the power cord into a grounded (earthed) electrical outlet that is easily

accessible at all times.

·In all European electrical environments, you must ground the Green/Yellow

tab on the power cord. If you do not ground the Green/Yellow tab, it can

cause an electrical shock due to high leakage currents.

Do not place objects on AC power cords or cables. Arrange them so that no

http://www.tyan.com

one might accidentally step on or trip over them.

·Do not pull on a cord or cable. When unplugging from the electrical outlet,

grasp the cord by the plug.

·To reduce the risk of electrical shock, disconnect all power cords before

servicing the appliance.

Equipment Batteries

· The system battery contains lithium manganese dioxide. If the battery pack

is not handled properly, there is risk of fire and burns.

·Do not disassemble, crush, puncture, short external contacts, or dispose of

the battery in fire or water.

·Do not expose the battery to temperatures higher than 60°C (140°F).

·The system battery is not replaceable. If the battery is replaced by an

incorrect type, there is danger of explosion. Replace the battery only with a

spare designated for your product.

·Do not attempt to recharge the battery.

·Dispose of used batteries according to the instructions of the manufacturer.

Do not dispose of batteries with the general household waste. To forward

them to recycling or proper disposal, use the public collection system or return

them to TYAN, your authorized TYAN partner, or their agents.

Equipment Modifications

· Do not make mechanical modifications to the system. TYAN is not

responsible for the regulatory compliance of TYAN equipment that has been

modified.

Equipment Repairs and Servicing

· The installation of internal options and routine maintenance and service of

this product should be performed by individuals who are knowledgeable about

the procedures, precautions, and hazards associated with equipment

containing hazardous energy levels.

·Do not exceed the level of repair specified in the procedures in the product

documentation. Improper repairs can create a safety hazard.

·Allow the product to cool before removing covers and touching internal

Inhaltsverzeichnis

Andere TYAN Server Handbücher

TYAN

TYAN TA77-B7061 Kurzanleitung

TYAN

TYAN Transport GX28 B2881 Bedienungsanleitung

TYAN

TYAN TS65-B8036 Kurzanleitung

TYAN

TYAN Transport TN27 B4987 Bedienungsanleitung

TYAN

TYAN Transport GS10 B2094T15 Bedienungsanleitung

TYAN

TYAN FT48 Kurzanleitung

TYAN

TYAN TN71-BP012 Bedienungsanleitung

TYAN

TYAN Transport GX18 Bedienungsanleitung

TYAN

TYAN FT83A-B7129 Kurzanleitung

TYAN

TYAN TN70-B7066 Kurzanleitung

TYAN

TYAN GA88-B5631 Kurzanleitung

TYAN

TYAN B8236G70W8HR-HE-IL Bedienungsanleitung

TYAN

TYAN FT83-B7119 Kurzanleitung

TYAN

TYAN Transport GX18 Bedienungsanleitung

TYAN

TYAN FT77B-B7059 Kurzanleitung

TYAN

TYAN GT20 B7002 Bedienungsanleitung

TYAN

TYAN Transport NR12 B6601 Bedienungsanleitung

TYAN

TYAN TS75-B8252 Kurzanleitung

TYAN

TYAN GT62B-B7076 Kurzanleitung

TYAN

TYAN B7058Y190X2 Kurzanleitung

TYAN

TYAN Tank GT25 (B5381) Kurzanleitung

TYAN

TYAN GT90-B7113 Kurzanleitung

TYAN

TYAN Tank GT14 B5180 Bedienungsanleitung

TYAN

TYAN Transport GT24 (B2932) Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung