Tyco Fire Product TY300-FRB Bedienungsanleitung

General

Description

The Series TY300-FRB, 5.6 K-factor

Sprinklers described in this data sheet

are quick responding, decorative 3 mm

glass bulb type spray sprinklers. Their

maximum rated service pressure of

300 psi (20,7 bar) makes them an ex-

cellent choice for systems that other-

wise would require the use of a pres-

sure control valve to reduce the static

pressure to 165 psi (11,4 bar), when

conventional 175 psi (12,1 bar) maxi-

mum rated pressure sprinklers are util-

ized. One of the most common uses for

theTY300-FRBSprinklersisinfire

protection systems for high rise build-

ings.

The recessed version of the Series

TY300-FRB Sprinklers are intended

for use in areas with a finished mount-

ing surface (i.e., ceiling or wall, as ap-

plicable). They use either a two-piece

Style 10 Recessed Escutcheon with

1/2 inch (12,7 mm) of recessed adjust-

ment or up to 3/4 inch (19,1 mm) of

total adjustment from the flush pen-

dent/sidewall position, or a two-piece

Style 20 Recessed Escutcheon with

1/4 inch (6,4 mm) of recessed adjust-

ment or up to 1/2 inch (12,7 mm) of

total adjustment from the flush pen-

dent/sidewall position. The adjustment

provided by the Recessed Escutcheon

reduces the accuracy to which the

fixed pipe to the sprinklers must be cut.

Corrosion resistant coatings, where

applicable, are utilized to extend the

life of copper alloy sprinklers beyond

that which would otherwise be ob-

tained when exposed to corrosive at-

mospheres. Although corrosion resis-

tant coated sprinklers have passed the

standard corrosion tests of the appli-

cable approval agencies, the testing is

not representative of all possible cor-

rosive atmospheres. Consequently, it

is recommended that the end user be

consulted with respect to the suitability

of these coatings for any given corro-

sive environment. The effects of ambi-

ent temperature, concentration of

chemicals, and gas/chemical velocity,

should be considered, as a minimum,

along with the corrosive nature of the

chemical to which the sprinklers will be

exposed.

WARNINGS

The Series TY300-FRB Sprinklers de-

scribed herein must be installed and

maintained in compliance with this

document, as well as with the applica-

ble standards of the National Fire Pro-

tection Association, in addition to the

standards of any other authorities hav-

ing jurisdiction. Failuretodosomay

impair the performance of these de-

vices.

The owner is responsible for maintain-

ing their fire protection system and de-

vices in proper operating condition.

The installing contractor or sprinkler

manufacturer should be contacted

with any questions.

Model/Sprinkler

Identification

Numbers

TY3105 - Upright 5.6K, 1/2"NPT

TY3205 - Pendent 5.6K, 1/2"NPT

TY3305 - HSW 5.6K, 1/2"NPT

TY3307 - EC HSW 5.6K, 1/2"NPT

† DuPont Registered Trademark

Series TY300-FRB — 5.6 K-factor

High Pressure Sprinklers, 300 psi (20,7 bar)

Quick Response, Standard & Extended Coverage

Page 1 of 8 TFP642

JULY, 2004

Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500

IMPORTANT

Always refer to Technical Data

Sheet TFP700 for the “INSTALLER

WARNING” that provides cautions

with respect to handling and instal-

lation of sprinkler systems and com-

ponents. Improper handling and in-

stallation can permanently damage

a sprinkler system or its compo-

nents and cause the sprinkler to fail

to operate in a fire situation or cause

it to operate prematurely.

OBSOLETE

Technical

Data

Approvals and

Maximum Working Pressure

UL & C-UL Listed and NYC Approved:

300 psi (20,7 bar).

FM Approved: 175 psi (12,1 bar).

(Refer to Table A for complete approval

information including corrosion resis-

tant status, as well as the Design Cri-

teria section for applicable system de-

sign criteria.)

Discharge Coefficient

K=5.6GPM/psi

1/2 (80,6 LPM/bar1/2)

Temperature Ratings

RefertoTableA

Finishes

Sprinkler: Refer to Table A

Recessed Escutcheon: White Coated,

Chrome Plated, or Brass Plated

Physical Characteristics

Frame............. Bronze

Button......... Brass/Copper

SealingAssembly ..........

. . . . . Beryllium Nickel w/Teflon†

Bulb...............Glass

Compression Screw . . . . . Bronze

Deflector ...........Copper

Operation

The glass Bulb contains a fluid which

expands when exposed to heat. When

the rated temperature is reached, the

fluid expands sufficiently to shatter the

glass Bulb, allowing the sprinkler to

activate and water to flow.

Design

Criteria

The Series TY300-FRB Upright

(TY3105), Pendent (TY3205), and

Horizontal Sidewall (TY3305) Sprin-

klers are intended for fire protection

systems designed in accordance with

the standard coverage installation

rules recognized by the applicable

Listing or Approval agency (e.g., UL

Listing is based on the requirements of

NFPA 13, and FM Approval is based

on the requirements of FM’s Loss Pre-

vention Data Sheets).

The Series TY-FRB Extended Cover-

age Horizontal Sidewall (TY3307)

Sprinklers are intended for light hazard

occupancy, smooth ceiling construc-

tion, fire protection systems designed

in accordance with the extended cov-

erage installation rules recognized by

the applicable Listing or Approval

agency (e.g., UL Listing is based on

the requirements of NFPA 13, and FM

Approval is based on the requirements

of FM’s Loss Prevention Data Sheets).

Refer to Table B or C for the applicable

coverage area and flow rate criteria.

Only the Style 10 or 20 Recessed Es-

cutcheon, as applicable, is to be used

for recessed installations.

Installation

The Series TY300-FRB Sprinklers

must be installed in accordance with

the following instructions:

NOTES

Do not install any bulb type sprinkler if

the bulb is cracked or there is a loss of

liquid from the bulb. With the sprinkler

held horizontally, a small air bubble

should be present. The diameter of the

air bubble is approximately 1/16 inch

(1,6 mm) for the 135°F/57°C to 3/32

inch (2,4 mm) for the 286°F/141°C

temperature ratings.

A leak tight 1/2 inch NPT sprinkler joint

should be obtained with a torque of 7

to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi-

mum of 21 ft. lbs. (28,5 Nm) of torque

may be used to install sprinklers with

1/2 NPT connections. Higher levels of

torque may distort the sprinkler inlet

and cause leakage or impairment of

the sprinkler.

Do not attempt to make-up for insuffi-

cient adjustment in the escutcheon

plate by under- or over-tightening the

sprinkler. Readjust the position of the

sprinkler fitting to suit.

The Series TY300-FRB Pendent and

Upright Sprinklers must be installed

in accordance with the following in-

structions.

Step 1. Pendent sprinklers are to be

installed in the pendent position, and

upright sprinklers are to be installed in

the upright position.

Page2of8 TFP642

PENDENT CROSS SECTION

(55,6 mm)

2-3/16"

(38,1 mm)

1-1/2"

PLATE SEATING

ESCUTCHEON 7/16" (11,1 mm)

NOMINAL

MAKE-IN

FLATS

WRENCH

SURFACE

NPT

1/2"

RECESSED PENDENT UPRIGHT

2-7/8" (73,0 mm) DIA.

(11,1 mm)

NOMINAL

MAKE-IN

7/16"

RECESSED

STYLE 10 or 20

ESCUTCHEON

(55,6 mm)

2-3/16"

1/2" NPT

DEFLECTOR

SSU

SSP DEFLECTOR

FIGURE 1

QUICK RESPONSE SERIES TY300-FRB UPRIGHT (TY3105) AND PENDENT (TY3205) SPRINKLERS

5.6 K-FACTOR, 1/2 INCH NPT

1 - Frame

2-Button

3 - Sealing

Assembly

4 - Bulb

5 - Compression

Screw

6 - Deflector *Temperature rating is indicated on deflector or adjacent to

orifice seat on frame.

**Pipe thread connections per ISO 7/1 can be provided on

special request.

OBSOLETE

Step 2. With pipe thread sealant ap-

plied to the pipe threads, hand tighten

the sprinkler into the sprinkler fitting.

Step 3. Tighten the sprinkler into the

sprinkler fitting using only the W-Type

6 Sprinkler Wrench (Ref. Figure 10).

With reference to Figure 1, the W-Type

6 Sprinkler Wrench is to be applied to

the sprinkler wrench flats.

The Series TY300-FRB Recessed

Pendent Sprinklers must be installed

in accordance with the following in-

structions.

Step A. After installing the Style 10 or

20 Mounting Plate, as applicable, over

the sprinkler threads and with pipe

thread sealant applied to the pipe

threads, hand tighten the sprinkler into

the sprinkler fitting.

Step B. Tighten the sprinkler into the

sprinkler fitting using only the W-Type

7 Recessed Sprinkler Wrench (Ref.

Figure 11). With reference to Figure 1,

the W-Type 7 Recessed Sprinkler

Wrench is to be applied to the sprinkler

wrench flats.

Step C. After the ceiling has been in-

stalled or the finish coat has been ap-

plied, slide on the Style 10 or 20 Clo-

sure over the Series TY300-FRB

Sprinkler and push the Closure over

the Mounting Plate until its flange

comes in contact with the ceiling.

The Series TY300-FRB Horizontal

and EC Horizontal Sidewall Sprin-

klers must be installed in accordance

with the following instructions.

Step 1. Horizontal sidewall sprinklers

are to be installed in the horizontal

position with their centerline of water-

way perpendicular to the back wall and

parallel to the ceiling. The word “TOP”

on the Deflector is to face towards the

ceiling.

Step 2. With pipe thread sealant ap-

plied to the pipe threads, hand tighten

the sprinkler into the sprinkler fitting.

Step 3. Tighten the sprinkler into the

sprinkler fitting using only the W-Type

6 Sprinkler Wrench (Ref. Figure 10),

WithreferencetoFigure2or3,the

W-Type 6 Sprinkler Wrench is to be

applied to the wrench flats.

The Series TY300-FRB Recessed

Horizontal and EC Horizontal Side-

wall Sprinklers must be installed in

accordance with the following instruc-

tions.

Step A. Recessed horizontal sidewall

sprinklers are to be installed in the

horizontal position with their centerline

of waterway perpendicular to the back

wall and parallel to the ceiling. The

TFP642 Page 3 of 8

FIGURE 2

QUICK RESPONSE SERIES TY300-FRB

HORIZONTAL SIDEWALL (TY3305) SPRINKLERS

5.6 K-FACTOR, 1/2 INCH NPT

1 - Frame

2-Button

3 - Sealing

Assembly

4 - Bulb

5 - Compression

Screw

6 - Deflector

*Temperature rating is indicated on deflector or adjacent to orifice seat on frame.

**Pipe thread connections per ISO 7/1 can be provided on special request.

PLATE

ESCUTCHEON

(11,1 mm)

NOMINAL

MAKE-IN

SEATING

WRENCH

FLATS

1-1/2"

(38,1 mm)

2-3/16"

(55,6 mm)

7/16"

1-13/16"

(46,0 mm)

HAT

DEFLECTOR

1/2"

NPT

CENTERLINE

WATERWAY

OF SPRINKLER

9/16"

(14,3 mm)

SURFACE

FIGURE 3

QUIK RESPONSE - EXTENDED COVERAGE / EXTENDED COVERAGE

SERIES TY300-FRB HORIZONTAL SIDEWALL (TY3307) SPRINKLERS

5.6 K-FACTOR, 1/2 INCH NPT

1 - Frame

2-Button

3 - Sealing

Assembly

4 - Bulb

5 - Compression

Screw

6 - Deflector

7 - Ejection

Spring

*Temperature rating is indicated on deflector or adjacent to orifice seat on frame.

**Pipe thread connections per ISO 7/1 can be provided on special request.

(11,1 mm)

NOMINAL

MAKE-IN

WRENCH

FLATS

1-1/2"

(38,1 mm)

2-3/16"

(55,6 mm)

7/16"

1-9/16"

(39,7 mm)

HAT

DEFLECTOR

1/2"

NPT

(11,1 mm)

7/16"

(11,1 mm)

7/16"

OF SPRINKLER

WATERWAY

CENTERLINE

OBSOLETE

Page4of8 TFP642

TYPE TEMP. BULB

LIQUID

NATURAL

BRASS

CHROME

PLATED

WHITE***

POLYESTER

155°F/68°C

175°F/79°C

200°F/93°C

SPRINKLER FINISH (See Note 6)

RECESSED

PENDENT

(TY3205)*

Figure 4

135°F/57°C Orange

Red

Yellow

Green

1, 5

NOTES:

1. Listed by Underwriters Laboratories, Inc. (UL) and for use in Canada (C-UL) as Quick Response Sprinklers (300 psi).

2. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers (175 psi).

3. Listed by Underwriters Laboratories, Inc. (UL) and for use in Canada (C-UL) per Table B (300 psi).

4. Approved by Factory Mutual Research Corporation (FM) per Table C (175 psi).

5. Approved by the City of New York under MEA 354-01-E (300 psi)

6. Where Polyester Coated Sprinklers are noted to be UL and C-UL Listed, the sprinklers are UL and C-UL Listed as Corrosion Resistant

Sprinklers.

* Installed with Style 10 (1/2" NPT) 3/4" Total Adjustment Recessed Escutcheon.

** Installed with Style 20 (1/2" NPT) 1/2" Total Adjustment Recessed Escutcheon.

*** Frame and deflector only. Listings and approvals apply to color (Special Order).

TABLE A, LABORATORY LISTINGS AND APPROVALS

5.6

1/2"

NPT

PENDENT

(TY3205)

and

UPRIGHT

(TY3105)

135°F/57°C Orange

155°F/68°C Red

175°F/79°C Yellow

200°F/93°C Green

286°F/141°C Blue

1, 2, 5

RECESSED

HSW

(TY3305)*

Figure 6

135°F/57°C

Orange155°F/68°C

Red175°F/79°C

Yellow200°F/93°C

5.6

1/2"

NPT

HSW

(TY3305)

135°F/57°C

155°F/68°C

175°F/79°C

200°F/93°C

286°F/141°C Blue

Green

Yellow

Red

Orange

1, 2, 5

135°F/57°C

155°F/68°C

175°F/79°C

200°F/93°C

Green

RECESSED

PENDENT

(TY3205)**

Figure 5

Orange

Red

Yellow

Green

1, 2, 5

Orange

Red

Yellow

Green

1, 2, 5

RECESSED

HSW

(TY3305)**

Figure 7

135°F/57°C

155°F/68°C

175°F/79°C

200°F/93°C

1, 5

EC HSW

(TY3307)

135°F/57°C

155°F/68°C

175°F/79°C

Orange

Red

Yellow

5.6

1/2"

NPT

RECESSED

EC HSW

(TY3307)*

Figure 8

135°F/57°C

155°F/68°C

175°F/79°C

Orange

Red

Yellow

RECESSED

EC HSW

(TY3307)**

Figure 9

135°F/57°C

155°F/68°C

175°F/79°C

Orange

Red

Yellow

3, 4, 5

3, 5

3, 4, 5

1, 5

OBSOLETE

TFP642 Page 5 of 8

FIGURE 4

SERIES TY300-FRB RECESSED PENDENT

SPRINKLER ASSEMBLY WITH TWO-PIECE

3/4 INCH TOTAL ADJUSTMENT

STYLE 10 RECESSED ESCUTCHEON

5.6 K-FACTOR, 1/2 INCH NPT

(57,2 mm)

2-1/4" DIA.

(73,0 mm)

2-7

8" DIA.

SPRINKLER

MOUNTING

CLOSURE SERIES

SURFACE

FACE OF

FITTING

(15,9±6,4 mm)

5/8±1/4"

(3,2 mm)

3/4" (19,1 mm)

1-1/4" (31,8 mm)

PLATE

MOUNTING

1/8"

1/4" (6,4 mm)

3/4" (19,1 mm)

TY-FRB

FIGURE 6

SERIES TY300-FRB RECESSED HORIZONTAL

SIDEWALL SPRINKLER WITH TWO-PIECE

3/4 INCH TOTAL ADJUSTMENT

STYLE 10 RECESSED ESCUTCHEON

5.6 K-FACTOR, 1/2 INCH NPT

MOUNTING

3/4"

(

19,1 mm

)

1-1/4" (31,8 mm)

PLATE

CLOSURE

SURFACE

MOUNTING

(73,0 mm)

2-1/4" DIA.

(57,2 mm)

1/4"

(

6,4 mm

)

3/4" (19,1 mm)

(3,2 mm)

1/8"

8±1

FACE OF

FITTING

SPRINKLER

(15,9±6,4 mm)

2-7/8" DIA.

SERIES

TY-FRB

FIGURE 5

SERIES TY300-FRB RECESSED PENDENT

SPRINKLER ASSEMBLY WITH TWO-PIECE

1/2 INCH TOTAL ADJUSTMENT

STYLE 20 RECESSED ESCUTCHEON

5.6 K-FACTOR, 1/2 INCH NPT

FIGURE 7

SERIES TY300-FRB RECESSED HORIZONTAL

SIDEWALL SPRINKLER WITH TWO-PIECE

1/2 INCH TOTAL ADJUSTMENT

STYLE 20 RECESSED ESCUTCHEON

5.6 K-FACTOR, 1/2 INCH NPT

(12,7±3,2 mm)

1/2±1/8"

2-1/4" DIA.

(57,2 mm)

(73,0 mm)

2-7

8" DIA.

SPRINKLER

MOUNTING

CLOSURE

SURFACE

FACE OF

FITTING

(3,2 mm)

1" (25,4 mm)

1-1/4" (31,8 mm)

PLATE

MOUNTING

1/8"

1/4" (6,4 mm)

1/2" (12,7 mm)

TY-FRB

SERIES

MOUNTING

(

25,4 mm

)

1-1/4" (31,8 mm)

PLATE

CLOSURE

SURFACE

MOUNTING

(73,0 mm)

2-1/4" DIA.

(57,2 mm)

1/4"

(

6,4 mm

)

1/2" (12,7 mm)

(3,2 mm)

1/8"

2±1

FACE OF

FITTING

SPRINKLER

(12,7±3,2 mm)

2-7/8" DIA.

SERIES

TY-FRB

OBSOLETE

word “TOP” on the Deflector is to face

towards the ceiling.

Step B. After installing the Style 10 or

20 Mounting Plate over the sprinkler

threads, hand tighten the sprinkler into

the sprinkler fitting.

Step C. Tighten the sprinkler into the

sprinkler fitting using only the W-Type

7 Recessed Sprinkler Wrench (Ref.

Figure 11). With reference to Figure 2

or 3, the W-Type 7 Recessed Sprinkler

Wrench is to be applied to the sprinkler

wrench flats.

Step D. After the wall has been in-

stalled or the finish coat has been ap-

plied, slide on the Style 10 or 20 Clo-

sure over the Series TY300-FRB

Sprinkler and push the Closure over

the Mounting Plate until its flange

comes in contact with the wall.

Care and

Maintenance

The Series TY300-FRB Sprinklers

must be maintained and serviced in

accordance with the following instruc-

tions:

NOTES

Before closing a fire protection system

main control valve for maintenance

work on the fire protection system that

it controls, permission to shut down the

affected fire protection system must be

obtained from the proper authorities

and all personnel who may be affected

by this action must be notified.

Absence of an escutcheon, which is

used to cover a clearance hole, may

delay the time to sprinkler operation in

a fire situation.

Sprinklers that are found to be leaking

or exhibiting visible signs of corrosion

must be replaced.

Automatic sprinklers must never be

painted, plated, coated or otherwise

altered after leaving the factory. Modi-

fied sprinklers must be replaced.

Sprinklers that have been exposed to

corrosive products of combustion, but

have not operated, should be replaced

if they cannot be completely cleaned

by wiping the sprinkler with a cloth or

by brushing it with a soft bristle brush.

Care must be exercised to avoid dam-

age to the sprinklers - before, during,

and after installation. Sprinklers dam-

aged by dropping, striking, wrench

twist/slippage, or the like, must be re-

placed. Also, replace any sprinkler that

has a cracked bulb or that has lost

liquid from its bulb. (Ref. Installation

Section).

Frequent visual inspections are rec-

ommended to be initially performed for

corrosion resistant coated sprinklers,

after the installation has been com-

pleted, to verify the integrity of the cor-

rosion resistant coating. Thereafter,

annual inspections per NFPA 25

should suffice; however, instead of in-

specting from the floor level, a random

sampling of close-up visual inspec-

tions should be made, so as to better

determine the exact sprinkler condi-

tion and the long term integrity of the

corrosion resistant coating, as it may

be affected by the corrosive conditions

present.

The owner is responsible for the in-

spection, testing, and maintenance of

their fire protection system and de-

vices in compliance with this docu-

ment, as well as with the applicable

standards of the National Fire Protec-

tion Association (e.g., NFPA 25), in

addition to the standards of any other

authorities having jurisdiction. The in-

stalling contractor or sprinkler manu-

facturer should be contacted relative

to any questions.

It is recommended that automatic

sprinkler systems be inspected,

tested, and maintained by a qualified

Inspection Service in accordance with

local requirements and/or national

codes.

Page6of8 TFP642

FIGURE 8

SERIES TY300-FRB RECESSED EXTENDED

COVERAGE HORIZONTAL SIDEWALL

SPRINKLER ASSEMBLY WITH TWO-PIECE

3/4 INCH TOTAL ADJUSTMENT

STYLE 10 RECESSED ESCUTCHEON

5.6 K-FACTOR, 1/2 INCH NPT

FIGURE 9

SERIES TY300-FRB RECESSED EXTENDED

COVERAGE HORIZONTAL SIDEWALL

SPRINKLER ASSEMBLY WITH TWO-PIECE

1/2 INCH TOTAL ADJUSTMENT

STYLE 20 RECESSED ESCUTCHEON

5.6 K-FACTOR, 1/2 INCH NPT

MOUNTING

1" (25,4 mm)

1-1/4" (31,8 mm)

PLATE

CLOSURE

SURFACE

MOUNTING

(73,0 mm)

2-1/4" DIA.

(57,2 mm)

1/4" (6,4 mm)

1/2" (12,7 mm)

(3,2 mm)

1/8"

FACE OF

FITTING

SPRINKLER

2-7/8" DIA.

TY-FRB

SERIES

2±1

(12,7±3,2 mm)

MOUNTING

3/4"

(

19,1 mm

)

1-1/4" (31,8 mm)

PLATE

CLOSURE

SURFACE

MOUNTING

(73,0 mm)

2-1/4" DIA.

(57,2 mm)

1/4"

(

6,4 mm

)

3/4" (19,1 mm)

(3,2 mm)

1/8"

FACE OF

FITTING

SPRINKLER

2-7/8" DIA.

(15,9±6,4 mm)

8±1

TY-FRB

SERIES

OBSOLETE

TFP642 Page 7 of 8

5.6 K EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLER (TY3307)

Response Coverage Minimum Minimum Deflector- Sprinkler Minimum

Rating Area(1),Flow

(2), Pressure(2), To-Ceiling Temperature Spacing(4),

Ft. x Ft. (m x m) GPM (LPM) PSI (BAR) Distance(3), In. (mm) Rating, °F Ft. (m)

Quick 16 x 16 (4,9 x 4,9) 26 (98) 21.6 (1,48) 4 to 12 (100 to 300) 135, 155, 175 10 (3,1)

Quick 16 x 18 (4,9 x 5,5) 29 (110) 26.8 (1,85) 4 to 12 (100 to 300) 135, 155, 175 10 (3,1)

Quick 16 x 20 (4,9 x 6,1) 32 (121) 32.7 (2,25) 4 to 6 (100 to 150) 135 10 (3,1)

Quick 16 x 22 (4,9 x 6,7) 35 (133) 39.1 (2,70) 4 to 6 (100 to 150) 135 10 (3,1)

Standard 16 x 20 (4,9 x 6,1) 32 (121) 32.7 (2.25) 4 to 6 (100 to 150) 155 10 (3,1)

Standard 16 x 22 (4,9 x 6,7) 35 (133) 39.1 (2,70) 4 to 6 (100 to 150) 155,175 10 (3,1)

TABLE B

UL AND C-UL LISTING COVERAGE AND FLOW RATE CRITERIA

FOR TY300-FRB (TY3307) EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLERS

NOTES

1. Backwall (where sprinkler is located) by sidewall (length of throw).

2. Requirement is based on minimum flow in GPM from each sprinkler. The indicted residual pressures are based on the nominal

K-factor.

3. The centerline of the sprinkler waterway is located 7/16 inch (11,1 mm) below the deflector (Ref. Figure 3).

4. Miinimum spacing is for lateral distance between sprinklers located along a single wall. Otherwise adjacent sprinklers (i.e., side-

wall sprinklers on an adjacent wall, on an opposite wall, or pendent sprinklers) must be located outside of the maximum listed pro-

tection area of the extended coverage sidewall sprinkler being utilized.

5.6 K EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLER (TY3307)

Response Coverage Minimum Minimum Deflector- Sprinkler Minimum

Rating Area(1),Flow

(2), Pressure(2), To-Ceiling Temperature Spacing(4),

Ft. x Ft. (m xm) GPM (LPM) PSI (BAR) Distance(3), In. (mm) Rating, °F Ft. (m)

Quick 16 x 16 (4,9 x 4,9) 26 (98) 22 (1,51) 4 to 12 (100 to 300) 135, 155 10 (3,1)

Quick 16 x 18 (4,9 x 5,5) 30 (114) 29 (2,00) 4 to 12 (100 to 300) 135, 155 10 (3,1)

Quick 16 x 20 (4,9 x 6,1) 33 (125) 35 (2,41) 4 to 12 (100 to 300) 135, 155 10 (3,1)

Standard 16 x 16 (4,9 x 4,9) 26 (98) 22 (1,51) 4 to 12 (100 to 300) 175 10 (3,1)

Standard 16 x 18 (4,9 x 5,5) 30 (114) 29 (2,00) 4 to 12 (100 to 300) 175 10 (3,1)

Standard 16 x 20 (4,9 x 6,1) 33 (125) 35 (2,41) 4 to 12 (100 to 300) 175 10 (3,1)

TABLE C

FM COVERAGE AND FLOW RATE CRITERIA

FOR TY300-FRB (TY3307) EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLERS

NOTES

1. Backwall (where sprinkler is located) by sidewall (length of throw).

2. Requirement is based on maintaining both minimum flow and minimum residual pressure.

3. The centerline of the sprinkler waterway is located 7/16 inch (11,1 mm) below the deflector (Ref. Figure 3).

4. Miinimum spacing is for lateral distance between sprinklers located along a single wall. Otherwise adjacent sprinklers (i.e.,

sidewall sprinklers on an adjacent wall, on an opposite wall, or pendent sprinklers) must be located outside of the maximum

listed protection area of the extended coverage sidewall sprinkler being utilized.

OBSOLETE

Limited

Warranty

Products manufactured by Tyco Fire

Products are warranted solely to the

original Buyer for ten (10) years

against defects in material and work-

manship when paid for and properly

installed and maintained under normal

use and service. This warranty will ex-

pire ten (10) years from date of ship-

ment by Tyco Fire Products. No war-

ranty is given for products or

components manufactured by compa-

nies not affiliated by ownership with

Tyco Fire Products or for products and

components which have been subject

to misuse, improper installation, corro-

sion, or which have not been installed,

maintained, modified or repaired in ac-

cordance with applicable Standards of

the National Fire Protection Associa-

tion, and/or the standards of any other

Authorities Having Jurisdiction. Mate-

rials found by Tyco Fire Products to be

defective shall be either repaired or

replaced, at Tyco Fire Products’ sole

option. Tyco Fire Products neither as-

sumes, nor authorizes any person to

assume for it, any other obligation in

connection with the sale of products or

parts of products. Tyco Fire Products

shall not be responsible for sprinkler

system design errors or inaccurate or

incomplete information supplied by

Buyer or Buyer’s representatives.

IN NO EVENT SHALL TYCO FIRE

PRODUCTS BE LIABLE, IN CON-

TRACT, TORT, STRICT LIABILITY OR

UNDER ANY OTHER LEGAL THE-

ORY, FOR INCIDENTAL, INDIRECT,

SPECIAL OR CONSEQUENTIAL

DAMAGES, INCLUDING BUT NOT

LIMITED TO LABOR CHARGES, RE-

GARDLESS OF WHETHER TYCO

FIRE PRODUCTS WAS INFORMED

ABOUT THE POSSIBILITY OF SUCH

DAMAGES,ANDINNOEVENT

SHALL TYCO FIRE PRODUCTS’ LI-

ABILITY EXCEED AN AMOUNT

EQUAL TO THE SALES PRICE.

THE FOREGOING WARRANTY IS

MADE IN LIEU OF ANY AND ALL

OTHER WARRANTIES EXPRESS OR

IMPLIED, INCLUDING WARRANTIES

OF MERCHANTABILITY AND FIT-

NESS FOR A PARTICULAR PUR-

POSE.

Ordering

Procedure

When placing an order, indicate the full

product name. Refer to the Price List

for complete listing of Part Numbers.

Contact your local distributor for avail-

ability.

Sprinkler Assemblies with NPT

Thread Connections:

Specify: (Specify Model/SIN), 3 mm

Bulb Type, 5.6 K-factor, (specify tem-

perature rating), Series TY300-FRB

(specify Pendent, Upright, Horizontal

Sidewall, or EC Horizontal Sidewall)

Sprinkler with (specify type of finish or

coating), P/N (specify from Table D).

Recessed Escutcheon:

Specify: Style (specify) Recessed Es-

cutcheon with (specify finish), P/N

(specify).

1/2" (15 mm)

Style 10

Chrome Plated . . . . . . . . . . . . P/N 56-701-9-010

White Color Coated . . . . . . . . P/N 56-701-4-010

White RAL9010* . . . . . . . . . . . P/N 56-701-3-010

Brass Plated . . . . . . . . . . . . . . P/N 56-701-2-010

1/2" (15 mm)

Style 20

Chrome Plated . . . . . . . . . . . . P/N 56-705-9-010

White Color Coated . . . . . . . . P/N 56-705-4-010

White RAL9010* . . . . . . . . . . . P/N 56-705-3-010

Brass Plated . . . . . . . . . . . . . . P/N 56-705-2-010

* Eastern Hemisphere sales only.

Sprinkler Wrench:

Specify: W-Type 6 Sprinkler Wrench,

P/N 56-000-6-387.

Specify: W-Type 7 Sprinkler Wrench,

P/N 56-850-4-001.

Page8of8 TFP642

TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446

P/N 53 — XXX — X — XXX

155°F/68°C155

TEMPERATURE

RATING

135°F/57°C135

SPRINKLER

TABLE D

PART NUMBER SELECTION

SERIES TY300-FRB SPRINKLERS

175°F/79°C

286

200°F/93°C200

286°F/141°C

175

WHITE POLYESTER

NATURAL BRASS

MODEL/SIN

CHROME PLATED

370 5.6K UPRIGHT (1/2"NPT)

371 5.6K PENDENT (1/2"NPT)

378 5.6K HSW (1/2"NPT)

376 5.6K EC HSW (1/2"NPT)

(135, 155, or 175°F ONLY)

TY3105

TY3205

TY3305

TY3307

3 WHITE (RAL9010)*

* Eastern Hemisphere sales only

FIGURE 10

W-TYPE 6 SPRINKLER

WRENCH

WRENCH RECESS

(END "A" USED FOR

1/2" NPT MODELS)

WRENCH RECESS

(END "B" USED FOR

3/4" NPT MODELS

)

FIGURE 11

W-TYPE 7 RECESSED

SPRINKLER WRENCH

RECESS

WREN

WITH SPRINKLER

ENGAGEMENT

IN TO ENSURE

WREN

HIN

AREA

PUSH WRENCH

OBSOLETE

Inhaltsverzeichnis

Andere Tyco Fire Product Bewässerungssystem Handbücher

Tyco Fire Product

Tyco Fire Product CENTRAL LF Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Gem TFP1 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL ESLO Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL TY-B Series Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL K25-1 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL BVR Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL EC-25 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Gem AQUARIUS F990 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star Pulsar S160 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Gem F978 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star S190 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-GB QR Dry Pendent Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star Celeste S150 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL A Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL TFP1 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product TY-B Series Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL ESFR-25 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL ELO Optima Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star Galaxy SG-RES Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL BVR-2 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL DS-1 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL A Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL RFII Series Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product the 1 inch NPT outlet of a malleable iron threaded tee Star Luminous... Bedienungsanleitung

Beliebte Bewässerungssystem Handbücher anderer Marken

Hunter

Hunter Institutional Series Bedienungsanleitung

Cellfast

Cellfast 52-305 Bedienungsanleitung

Oral Care Technologies

Oral Care Technologies Hydro Floss Bedienungsanleitung

Reliable

Reliable F1-300 Bedienungsanleitung

Netafim

Netafim NETBEAT Bedienungsanleitung

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Bedienungsanleitung

Tyco

Tyco CC3 Bedienungsanleitung

Reliable

Reliable F4FR Bedienungsanleitung

OpenSprinkler

OpenSprinkler OSPi Bedienungsanleitung

EINHELL

EINHELL GE-WW 5537 E Bedienungsanleitung

Valley

Valley Bender160 Bedienungsanleitung

Reliable

Reliable F1FR42 Series Bedienungsanleitung

Reliable

Reliable F1FR-300 Bedienungsanleitung

Toro

Toro 730 Series Kurzanleitung

Eden

Eden 97063-EDAMZ Bedienungsanleitung

Tyco

Tyco TY-L Series Bedienungsanleitung

Johnson Controls

Johnson Controls tyco ESFR-17 Bedienungsanleitung

Victaulic

Victaulic VicFlex I-VICFLEX.AQC-U Bedienungsanleitung