TFP964
Page 6 of 6
NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association;
TEFLON is a trademark of The Chemours Company FC, LLC
1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone +1-215-362-0700
© 2021 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision date and are subject to change without notice.
Care and
Maintenance
The TYCO Model RM-2 Riser Manifold
must be serviced and maintained in
accordance with this section.
Before closing a fire protection system
control valve for inspection or main-
tenance work on the fire protection
system that it controls, obtain per-
mission to shut down the effected fire
protection system from the proper
authorities and notify all personnel who
may be affected by this action.
After placing a fire protection system
in service, notify the proper authorities
and advise those responsible for moni-
toring proprietary and/or central station
alarms.
The owner is responsible for the inspec-
tion, testing, and maintenance of their
fire protection system and devices in
compliance with this document, as well
as with the applicable standards of the
NATIONAL FIRE PROTECTION ASSO-
CIATION such as NFPA 25, in addition
to the standards of any authority having
jurisdiction. Contact the installing con-
tractor or product manufacturer with
any questions.
It is recommended that automatic
sprinkler systems be inspected, tested,
and maintained by a qualified Inspec-
tion Service in accordance with local
requirements and/or national codes.
Note: With the exception of the Model
TD-2 Test and Drain Valve and the
Model CV-1FR Riser Check Valve, do
not attempt to repair any component of
the Model RM-2 Riser Manifold in the
field. The Drain Valve Handwheel of the
Model TD-2 Test and Drain Valve may
be replaced in the field. Refer to Tech-
nical Data Sheet TFP950 for CV-1FR
repair information. Replace other com-
ponents as whole assemblies only. See
Figure 1 for component descriptions
and part numbers.
The alarm/flow test procedure results
in operation of the associated alarms.
Notify the owner and the fire depart-
ment, central station, or other signal
station to which the alarms are con-
nected, and the building occupants.
The following inspection procedure
must be performed as indicated, in
addition to any specific requirements
of the NFPA, and any impairment must
be immediately corrected:
Alarm/Flow Test Procedure
Step 1.
Rotate the test valve handle
180 degrees to the OPEN position as
shown in Figure 4.
Note: This action permits water to flow
through the orifice of the test valve sim-
ulating flow from an individual sprinkler
located downstream of the waterflow
alarm switch as shown in Figure 1.
Note: The test valve housing can be
rotated 360 degrees to eliminate equip-
ment interference with the test valve
handle as shown in Figure 4.
Do not rotate the test valve housing in
the closed position.
Step 2. Confirm water flow through the
test port by observing flow at the drain
port sight glass.
Step 3. Verify proper operation of the
waterflow alarm switch at the fire panel,
the addressable module, and the local
audible/visual annunciator if installed
as shown in Figure 3.
Step 4. Rotate the test valve handle 180
degrees back to the CLOSED position.
Limited
Warranty
For warranty terms and conditions, visit
www.tyco-fire.com.
Ordering
Procedure
Contact your local distributor for avail-
ability. When placing an order, indi-
cate the full product name, including
description and part number (P/N).
Riser Manifolds
Model RM-2 Riser Manifold
Specify: Model RM-2 Riser Manifold,
Size (specify), P/N (specify)
2 in. (DN50) . . . . . . . . . . . . . . . . . . . . . . 5940601
2-1/2 in. (DN65) . . . . . . . . . . . . . . . . . . . 5940 611
3 in. (DN80) . . . . . . . . . . . . . . . . . . . . . . 5940621
4 in. (DN100). . . . . . . . . . . . . . . . . . . . . . 5940651
6 in. (DN150). . . . . . . . . . . . . . . . . . . . . . 5940661
Accessories
Optional Flexible Drain Hose
See Figure 5 for part descriptions and
part numbers.
Specify: Flexible Drain Hose, P/N
(specify)
Optional Test and Drain Valve
Alternate Installation Kit
Specify: Size Range (specify) Model
RM-2 Riser Manifold, Test and
Drain Valve Alternate Installation Kit,
P/N (specify)
2 to 3 in. (DN50 to DN80). . . . . . . . . . . 59352691
4 to 6 in. (DN100 to DN150) . . . . . . . . . 59352692
Replacement Parts
See Figure 1 for part descriptions and
part numbers.
Specify: Model RM-2 Riser Manifold,
Replacement (specify part description),
P/N (specify)
Note: Refer to TFP965 for Model TD-2
Test and Drain Valve replacement parts.
