Tyco TFP PH2 Bedienungsanleitung

General

Description

The Model TFP PH2, 5.6 K-factor, In-

stitutional Pendent Sprinklers are

standard response - standard cover-

age, fusible solder type spray sprin-

klers designed for use in areas such as

correctional, detention, and mental

health care facilities.

The unique features of the Model TFP

PH2 provide a tamper resistant sprin-

kler design that helps eliminate the

opportunity for individuals to injure

themselves or others with the compo-

nents of a fire sprinkler. At the same

time, the Model TFP PH2 optimizes an

aesthetically appealing flush design

that conceals most of the operating

parts.

WARNING

The Model TFP PH2 Institutional Pen-

dent Sprinklers described herein must

be installed and maintained in compli-

ance with this document, as well as

with the applicable standards of the

National Fire Protection Association,

in addition to the standards of any

other authorities having jurisdiction.

Failure to do so may impair the integ-

rity of these devices.

The owner is responsible for maintain-

ing their fire protection system and de-

vices in proper operating condition.

The installing contractor or manufac-

turer should be contacted relative to

any questions.

Sprinkler

Identification

Number

SIN TY3290

Technical

Data

Approvals

UL and C-UL Listed.

(Refer to the Design Criteria section.)

NYC under MEA 351-01-E.

Maximum Working Pressure

175 psi (12,1 bar)

Inlet Thread Connection

1/2 inch NPT

Discharge Coefficient

K=5.6GPM/psi

1/2

(80,6 LPM/bar1/2)

Temperature Ratings

140°F/60°C,

165°F/74°C, or

212°F/100°C

Finishes

Sprinkler: Chrome Plated

Escutcheon: Chrome Plated

Physical Characteristics

Body.............. Brass

Deflector............Bronze

Deflector Reinforcement . . . . . . .

................Bronze

DeflectorPost.........Bronze

Deflector Post Pin . . . . . . Bronze

DeflectorCore ........Bronze

Compression Screw . . . . . Bronze

Lever . . . . . . . . . . . . . Bronze

ReleaseSpring ........Bronze

CoreSleeve......... Copper

SealingAssembly...........

. . . . . . Beryllium Nickel w/ Teflon*

FusibleElement............

. . . Solder, Copper, Stainless Steel

Dust Cover . . Chrome Plated Steel

Operation

In the standby condition, the design of

theModelTFPPH2issuchthata

suspended load of 80 lbs. (36 kg) or

more applied to the linkage mecha-

nism will release the sprinkler. Also,

when properly installed, the escutch-

eonisheldfasttotheceilingtodeter

its removal. The shape of the escutch-

eon cannot be easily grasped, which

further deters tampering.

A fusible solder operating element se-

cures the linkage mechanism of the

Model TFP PH2. When the rated tem-

perature is reached, the solder melts

releasing the linkage mechanism that

holds the sprinkler closed. This allows

the deflector to extend downward and

water to flow.

Design

Criteria

The 5.6 K-factor, Model TFP PH2 (SIN

TY3290) Institutional Pendent Sprin-

klers are intended for use with fire pro-

tection systems designed in accord-

ance with the standard installation

rules recognized by the applicable

Listing or Approval agency (e.g., UL

Model TFP PH2 — 5.6 K-factor

Institutional Pendent Sprinklers

Standard Response, Standard Coverage

Page 1 of 4 TFP650

JANUARY, 2003

Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500

Customer Service/Sales:

Tel: (215) 362-0700 / (800) 523-6512

Fax: (215) 362-5385

Listing is based on NFPA 13 require-

ments).

Only the Institutional Escutcheons

shown in Figure 2 can be utilized with

the Model TFP PH2. A maximum of

three Model 1752 Spacers can only be

utilized with Style B1 or C Institutional

Escutcheons when vertical adjustment

is desired.

NOTE

Integrity of the tamper resistant design

of the Institutional Escutcheons is de-

pendent on the piping installation de-

sign. When installed properly, the In-

stitutional Escutcheon is held fast to

the mounting surface by the tightening

of the sprinkler assembly into the

sprinkler fitting. In order to accomplish

a proper installation, the sprinkler fit-

ting must be properly located with re-

spect to distance from the face of the

sprinkler fitting to the face of the

mounting surface (Ref. Fig. 2); the

sprinkler fitting being rigidly secured

and held immobile; and, the centerline

of the sprinkler fitting being perpen-

dicular to the mounting surface to as-

sure that the escutcheon sits squarely

against the mounting surface around

the entire perimeter of the Institutional

Escutcheon.

Installation

The 5.6 K-factor, Model TFP PH2

Sprinklers must be installed in accord-

ance with the following instructions:

NOTES

Refer to the Design Criteria section for

important information regarding the

piping installation design and its effect

on maintaining the integrity of the tam-

per resistant design of the Institutional

Escutcheons.

A leak tight 1/2 inch NPT sprinkler joint

should be obtained with a torque of 7

to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi-

mum of 21 ft.lbs. (28,5 Nm) of torque

is to be used to install these sprinklers.

Higher levels of torque may distort the

sprinkler inlet with consequent leak-

age or impairment of the sprinkler.

Do not attempt to compensate for im-

proper location of the sprinkler fitting

by under- or over-tightening the sprin-

kler. Readjust the position of the sprin-

kler fitting to suit, or increase or de-

crease the number of Model 1752

Spacers, as applicable.

After the installation is complete, make

certain that the Institutional Escutch-

eon is held fast to the mounting sur-

face and that it sits squarely against

the ceiling around its entire perimeter.

Step 1. The TFP PH2 Sprinklers must

be installed pendent and with the cen-

terline of their waterway perpendicular

to the ceiling.

Step 2. With the Institutional Escutch-

eon in place and with pipe thread

sealant applied to the pipe threads,

hand tighten the sprinkler into the

sprinkler fitting.

Step 3. Wrench tighten the Sprinkler

using only the Model 1509-3 Sprinkler

Wrench (Ref. Fig. 4). The wrenching

teeth of the Sprinkler Wrench are to be

applied to the sprinkler wrenching

notch areas (Ref. Fig. 1).

Step 4. After the installation is com-

plete, make certain that the Institu-

tional Escutcheon is held fast to the

mounting surface and that it sits

squarely against the ceiling around its

entire perimeter.

FIGURE 1

MODEL TFP PH2 INSTITUTIONAL PENDENT SPRINKLER

Components:

1 - Body

2 - Deflector

3 - Deflector

Reinforcement

4 - Deflector Post

(2req’d)

5 - Deflector Post

Pin (2 req’d)

6 - Deflector Core

7 - Compression

Screw

8 - Lever

9 - Release Spring

10 - Core Sleeve

11 - Sealing Assembly

12 - Fusible Element

13 - Dust Cover

CROSS-SECTION

2" NPT

VIEW

SPRINKLER

WRENCHING

NOTCH (2)

DEFLECTOR

IN OPERATED

POSITION

SPRINKLER

FITTING

FACE OF

NOMINAL MAKE-IN

7/16" (11.1 mm)

(80.8 mm)

3.18"

2.81"

(71.4 mm)

INSTALLED

SIDE VIEW SIDE VIEW

OPERATED

Page2of4 TFP650

* Registered Trademark of DuPont

Care and

Maintenance

The 5.6 K-factor, Model TFP PH2

Sprinklers must be maintained and

serviced in accordance with the follow-

ing instructions:

NOTES

Service inspections should be made

on a regular basis to detect possible

damage or alterations to the sprinkler

and escutcheon. Inspections should

include making certain that the Institu-

tional Escutcheon is held fast to the

mounting surface. Damaged or altered

sprinklers are to be replaced immedi-

ately to avoid personal injury and to

prevent use for causing personal in-

jury, as well as to maintain the sprin-

kler system in an operative condition.

Before closing a fire protection system

main control valve for maintenance

work on the fire protection system that

it controls, permission to shut down the

affected fire protection systems must

be obtained from the proper authori-

ties and all personnel who may be

affected by this action must be notified.

Sprinklers that are found to be leaking

or exhibiting visible signs of corrosion

must be replaced.

Automatic sprinklers must never be

painted, plated, coated, or otherwise

altered after leaving the factory. Modi-

fied or over-heated sprinklers must be

replaced.

Care must be exercised to avoid dam-

age to the sprinklers - before, during,

and after installation. Sprinklers dam-

aged by dropping, striking, wrench

twist/slippage, or the like, must be re-

placed.

The owner is responsible for the in-

spection, testing, and maintenance of

their fire protection system and de-

vices in compliance with this docu-

ment, as well as with the applicable

standards of the National Fire Protec-

tion Association (e.g., NFPA 25), in

addition to the standards of any other

authorities having jurisdiction. The in-

stalling contractor or sprinkler manu-

facturer should be contacted relative to

any questions.

It is recommended that automatic

sprinkler systems be inspected,

tested, and maintained by a qualified

Inspection Service.

FIGURE 2

INSTITUTIONAL ESCUTCHEON OPTIONS

FOR USE WITH THE MODEL TFP PH2

TFP650 Page 3 of 4

2.59" (65.8 mm) MIN.

STYLE C

(30.2 mm)

1-3/16"

SPACERS

THREE

#1752

UP TO

3-1/4" DIA. 1.19"

(65.1 mm)

#1752

THREE

UP TO

2-9/16"

SPACERS

WITH 3

STYLE B1

2.81" (71.4 mm) MAX.

(108.0 mm)

4-1/4" DIA.

0.22" (5.6 mm) MAX.

(82.6 mm) (30.2 mm)

FLUSH MIN.

3/16"

(4.8 mm)

STYLE A

1.62"

(41.1 mm)

BY CLEARANCE FOR

REDUCING COUPLING

5" DIA.

(127.0 mm)

1.48" (37.6 mm) MIN.

1.70" (43.2 mm) MAX.

1.33" (33.8 mm) MAX.

1.11" (28.2 mm) MIN.

DIAMETER DETERMINED

REDUCING COUPLING

BY CLEARANCE FOR

DIAMETER DETERMINED

REDUCING COUPLING

BY CLEARANCE FOR

DIAMETER DETERMINED

(1)

(2)

(1)

(2)

WITH NO SPACERS

WITH 3 SPACERS

(2)

(1)

WITH NO SPACERS

WITH 3 SPACERS

(2)

(1)

SPACERS

(1)

(2)

(1)

(2)

NOTE: Model 1752 Spacers are not to be used to ob-

tain vertical adjustment for the Model TFP PH2 with

Style A Escutcheons.

Limited

Warranty

Products manufactured by Tyco Fire

Products are warranted solely to the

original Buyer for ten (10) years

against defects in material and work-

manship when paid for and properly

installed and maintained under normal

use and service. This warranty will ex-

pire ten (10) years from date of ship-

ment by Tyco Fire Products. No war-

ranty is given for products or

components manufactured by compa-

nies not affiliated by ownership with

Tyco Fire Products or for products and

components which have been subject

to misuse, improper installation, corro-

sion, or which have not been installed,

maintained, modified or repaired in ac-

cordance with applicable Standards of

the National Fire Protection Associa-

tion, and/or the standards of any other

Authorities Having Jurisdiction. Mate-

rials found by Tyco Fire Products to be

defective shall be either repaired or

replaced, at Tyco Fire Products’ sole

option. Tyco Fire Products neither as-

sumes, nor authorizes any person to

assume for it, any other obligation in

connection with the sale of products or

parts of products. Tyco Fire Products

shall not be responsible for sprinkler

system design errors or inaccurate or

incomplete information supplied by

Buyer or Buyer’s representatives.

IN NO EVENT SHALL TYCO FIRE

PRODUCTS BE LIABLE, IN CON-

TRACT, TORT, STRICT LIABILITY OR

UNDER ANY OTHER LEGAL THE-

ORY, FOR INCIDENTAL, INDIRECT,

SPECIAL OR CONSEQUENTIAL

DAMAGES, INCLUDING BUT NOT

LIMITED TO LABOR CHARGES, RE-

GARDLESS OF WHETHER TYCO

FIRE PRODUCTS WAS INFORMED

ABOUT THE POSSIBILITY OF SUCH

DAMAGES,ANDINNOEVENT

SHALL TYCO FIRE PRODUCTS’ LI-

ABILITY EXCEED AN AMOUNT

EQUAL TO THE SALES PRICE.

THE FOREGOING WARRANTY IS

MADE IN LIEU OF ANY AND ALL

OTHER WARRANTIES EXPRESS OR

IMPLIED, INCLUDING WARRANTIES

OF MERCHANTABILITY AND FIT-

NESS FOR A PARTICULAR PUR-

POSE.

Ordering

Procedure

Contact your local distributor for avail-

ability.

Sprinkler Assemblies:

Specify: 5.6 K-factor, Chrome Plated,

(specify temperature rating), Model

TFP PH2 (TY3290) Institutional Pen-

dent Sprinkler.

140F/60C. . . . . . . . . . . . . . . . . P/N 51-104-9-140

165F/74C. . . . . . . . . . . . . . . . . P/N 51-104-9-165

212F/100C . . . . . . . . . . . . . . . P/N 51-104-9-212

Separately Ordered Escutcheons:

Specify: Style (A, B1, or C), Chrome

Plated, Institutional Escutcheons.

Style A . . . . . . . . . . . . . . . . . . . P/N 56-012-7-622

Style B1 . . . . . . . . . . . . . . . . . . P/N 56-001-7-511

Style C. . . . . . . . . . . . . . . . . . . P/N 56-001-7-513

Separately Ordered Wrenches:

Specify: Model 1509-3 Sprinkler

Wrench, P/N 56-001-5-093.

Separately Ordered Spacers For

Vertical Adjustment:

Specify: Model 1752 Spacers for use

with Style B-1 and C Institutional Es-

cutcheons, P/N 56-000-1-752.

Separately Ordered Parts For In-

stallation In Concrete With

Type A Escutcheon:

Specify: Model 1753 Recessed Cup

for use with Style A Escutcheon for

installation in concrete,

P/N 56-000-1-753.

Specify: Model 1290-8 Pipe Plug With

Shoulder for use with Style A Escutch-

eon for installation in concrete,

P/N 56-001-2-908.

Specify: Model 1754 Pipe Support for

use with Style A Escutcheon for instal-

lation in concrete, P/N 56-000-1-754.

FIGURE 4

MODEL 1509-3

SPRINKLER WRENCH

FIGURE 3

INSTALLATION IN CONCRETE WITH STYLE A ESCUTCHEON

2" DRIVE

ACCEPTS

TEETH

WREN

HIN

Page4of4 TFP650

TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446

Andere Tyco Bewässerungssystem Handbücher

Tyco

Tyco ESFR-22 Bedienungsanleitung

Tyco

Tyco EC-11 Series Bedienungsanleitung

Tyco

Tyco FASTFLEX YN25 Bedienungsanleitung

Tyco

Tyco ESFR-1 Bedienungsanleitung

Tyco

Tyco ESFR-22 Bedienungsanleitung

Tyco

Tyco ESFR-17 Bedienungsanleitung

Tyco

Tyco AQUAMIST ULF AM27 Bedienungsanleitung

Tyco

Tyco Power Pro Series Bedienungsanleitung

Tyco

Tyco CC3 Bedienungsanleitung

Tyco

Tyco ELO-231B Series Bedienungsanleitung

Tyco

Tyco rapid response LFII Series Bedienungsanleitung

Tyco

Tyco RFII-C Series Bedienungsanleitung

Tyco

Tyco DS-1 Series Bedienungsanleitung

Tyco

Tyco LFII Series Bedienungsanleitung

Tyco

Tyco EC-5 Series Bedienungsanleitung

Tyco

Tyco Ultra K17 Bedienungsanleitung

Tyco

Tyco EC-5 Series Bedienungsanleitung

Tyco

Tyco Rapidresponse LFII Series Bedienungsanleitung

Tyco

Tyco ESFR-25 Bedienungs- und Wartungsanleitung

Tyco

Tyco Rapidresponse LFII Series Bedienungsanleitung

Tyco

Tyco TY-FRB Series Bedienungsanleitung

Tyco

Tyco TY-FRB Series Bedienungsanleitung

Tyco

Tyco DS-2 Series Bedienungsanleitung

Tyco

Tyco TY-FRB Series Bedienungsanleitung

Beliebte Bewässerungssystem Handbücher anderer Marken

Hunter

Hunter Institutional Series Bedienungsanleitung

Cellfast

Cellfast 52-305 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL A Bedienungsanleitung

Oral Care Technologies

Oral Care Technologies Hydro Floss Bedienungsanleitung

Reliable

Reliable F1-300 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Gem F892 Bedienungsanleitung

Netafim

Netafim NETBEAT Bedienungsanleitung

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Bedienungsanleitung

Reliable

Reliable F4FR Bedienungsanleitung

OpenSprinkler

OpenSprinkler OSPi Bedienungsanleitung

EINHELL

EINHELL GE-WW 5537 E Bedienungsanleitung

Valley

Valley Bender160 Bedienungsanleitung

Reliable

Reliable F1FR42 Series Bedienungsanleitung

Reliable

Reliable F1FR-300 Bedienungsanleitung

Toro

Toro 730 Series Kurzanleitung

Eden

Eden 97063-EDAMZ Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-231 Bedienungsanleitung