TyloHelo 1601-40 Bedienungsanleitung

OPERATING INSTRUCTIONS

72-0134 11-26-2019 Rev A

Page 1

WARNING

SECTION 1: GENERAL INFORMATION

Do not take a sauna if using

alcohol, drugs or

medications.

Pregnant women or persons

with poor health should

consult their physician before

using any sauna.

Caution re hazard: Do not

use the sauna room for

drying clothes, bathing suits,

etc. Do not hang towels

above heater or place any

object other than the rocks

supplied on the heater. If any

darkening of the wall around

the heater is noticed

discontinue sauna use

immediately.

Inspect sauna regularly for

required maintenance to

heater, control and benches.

Replace wood surfaces

which show any signs of

deterioration.

The heater gets extremely hot

during operation and should

not be touched or burns may

result.

Minors should be adequately

supervised whenever near a

hot or warming sauna.

Sauna Control Models Pure 2.0

(Type # 1601-40 and 1601-40-1)

Read all instructions carefully before installation. Please leave all

instructions and warranty with the owner.

WARNING

Prolonged exposure to elevated temperatures is capable of inducing

hyperthermia. Hyperthermia occurs when the internal temperature of the

body reaches several degrees above the normal body temperature of

98.6°F. The symptoms of hyperthermia include an increase in the normal

temperature of the body, dizziness, lethargy, drowsiness, and fainting. The

effects of the hyperthermia include failure to perceive heat, failure to

recognize the need to exit the room, unawareness of impending hazard,

fetal damage in pregnant women, physical inability to exit the room and

unconsciousness.

WARNING

The use of alcohol, drugs, or medication is capable of greatly increasing

the risk of fatal hyperthermia.

The controls are ETL approved by Intertek for permanent installations and

electrical connections. Refer to the heater or steam generator “Installation

and Operation Instructions” for complete information about the electrical

wiring. All wiring must be performed in accordance with national and local

codes.

OPERATING INSTRUCTIONS

72-0134 11-26-2019 Rev A

Page 2

WARNING

SECTION 2: CONTROL OPERATION

Fire sprinkler systems used

inside any sauna room should

be properly rated for sauna

room temperatures.

Do not pour chlorinated pool

or spa water on heater.

Excessive water use on heater

may cause damage and void

warranty.

Electric Shock Hazard - High

voltage exists within this

equipment. There are no user

serviceable parts in this

equipment. All installation

and service to this equipment

should be performed by

qualied licensed personnel in

accordance with local and

national codes.

Do not construct sauna room

so as to restrict air ow

through the bottom of the

heater.

Packing the rocks too tightly

may cause the heater high

limit switch to trip.

A. On/Off Light switch

B. Indicators - lights for lighting, door switch (n/a), timer and the heater

C. On/Off Sauna Switch and fault alarms

D. Sets the desired value

E. Functions - Temperature, Delay Timer, Sauna Length and Humidity (n/a)

F. Function buttons

CONTROL OPERATION:

TURN ON LIGHT: Press the "light bulb" icon once to turn on the light and

press again to turn off. (Usage of light control is optional)

SAUNA LENGTH:

(Control 1601-40) Select the sauna length function by pressing the buttons

< > (F). Set the desired usage time (0–60 minutes) using the – and +

buttons. (Setting 10 equals 60 minutes)

(Control 1601-40-1) Usage time is 0-24 hours operation (Setting 1 = 2

hours, setting 10 = 24 hours) version has a maximum sauna length of 24

hours and can be used only when a facility has an attendant on duty to

monitor the people in the sauna .

SET TEMPERATURE: Press function button (F). Then you can choose the desired temperature 1–10 using buttons –

and +. (Setting 10 equals highest set point.)

When the desired temperature has been set and the heater is switched on the set temperature indicator light will remain

on and the current temperature indicator LED will ash. When the current temperature reaches the set value the

indicator light will stop ashing.

Version 1 2 3 4 5 6 7 8 9 10

1 hour 6 min 12 min 18 min 24 min 30 min 36 min 42 min 48 min 54 min 60 min

24 hour 2 hr 4 hr 6 hr 8 hr 10 hr 12 hr 14 hr 16 hr 18 hr 24 hr

LED

OPERATING INSTRUCTIONS

72-0134 11-26-2019 Rev A

Page 3

Shower

Sauna (10 - 15 min.)

Shower or swim

Rest (10 - 15 min.)

Relax with juice or water

You liked it?

Do it once again and

you will feel great.

SECTION 3: HOW TO TAKE A SAUNA

SECTION 2: OPERATION, Continued

• When taking a sauna, allow time to relax completely.

• Remove clothing and jewelry...if required, wear a towel loosely.

• After 10 minutes or when perspiration begins, leave sauna and relax in

dressing area...follow with a cool shower.

• Cooling time should equal time spent in sauna. Enter sauna room again

and stay 5 or 10 minutes.

• Repeat the cycle 2 or 3 times; end with a brisk shower...rinse in cool

water.

• Dress when completely dry and perspiration has stopped.

• Some sauna bathers enjoy the soothing effect of steam by splashing

water on the heated sauna rocks. Use only one dipper full (approx. ½

cup) at a time and keep clear of the steam as it rises off the rocks.

• Do not smoke, exercise or drink alcoholic beverages in the sauna room.

• Do not pour chlorinated pool or spa water on the heater or corrosion

damage may result.

FAHRENHEIT or CELSIUS: The temperature will be displayed in Fahrenheit as

default. To change the temperature display, apply power to the system for over 5

minutes and the LED temperature indicator must be glowing. Next, press the <

button for 5 seconds. After 2 seconds the temperature indicator will start ashing,

and a C or F will appear in the temperature display to indicate that the temperature

display has been changed.

START HEAT IMMEDIATELY:

Start the heater on by pressing the On/Off button. The latest temperature and

usage time settings will remain preset. A green indicator light will come on in area

(B) to indicate that the device has been switched on.

You may switch the system off before the usage time ends by pressing the same

button again. The indicator light will go out.

TIME DELAY START TIME: The control may be set to delay start mode to

activate the heater after a preset amount of time. Select the clock symbol using

the function button (F). Use the – and + buttons to select the amount of hours

(1–10 hours) after which the device will switch on. Activate a later start by

pressing the Start button (C).

The timer symbol light will come on (in eld B) and the selected time-lapse

indicator light will start ashing. The ashing indicator measures and indicates

the time leading up to the device being switched on. When the heater starts, the

control panel will automatically show the set temperature.

OPERATING INSTRUCTIONS

72-0134 11-26-2019 Rev A

Page 4

SECTION 4: TROUBLESHOOTING

Control will Run but No Heat - Press the (reset) high limit switch on the bottom of heater.

Slow Heat Time or High Limit Tripping - Check rock placement, they will break down over time and reduce the air

ow in the heater. Refer to Diagram 10 for proper rock installation. Discard all rocks under the size of 2" pieces. Call

the number below to order more rocks if needed.

CAUTION: Use only a contractor approved for 250,000 endurance Cycles / ATTENTION: Utiliser uniquement un

contacteur approuve pour 250,000 cycles de fanctionnement

In the event of a fault occurring in the heater system (control panel, temperature sensor, etc.), this will be signaled

by the LED indicator light on the control panel. The fault indicator light will be displayed on the 1-10 scale of the

control. The fault error code will be displayed with a constant LED light or a ashing LED light. See the list below for

fault codes.

Note: The LED indicators do not turn off, some indicators will glow as long as power is applied to the system.

Constant LED Fault Code (ones marked with “n/a” are not in use):

1 Temperature sensor not connected or shorted

2 n/a

3 Heater circuit board overheated

4 n/a

5 n/a

6 Communication lost between control and circuit board in heater.

7 n/a

8 n/a

9 n/a

10 n/a

Flashing LED Fault Code

1 n/a

2 n/a

3 n/a

4 n/a

5 n/a

6 n/a

7 n/a

8 n/a

9 Door Switch is open for more than 60 seconds while heating or jumper on circuit board in heater is removed.

10 Door Switch is open for more than 60 seconds in “Delay” Mode or jumper on circuit board in heater is removed.

For troubleshooting or service questions call 1-888-780-4427 and ask to speak with service. Prior to calling, please

have the Model and Type number available. You may also email us at techsuppor[email protected]

LED Flashes Red

during a fault

1 - 10 Indicates the

fault code

Dieses Handbuch passt für folgende Modelle

Andere TyloHelo Controller Handbücher

TyloHelo

TyloHelo SaunaChrome Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung