U-Line H-1026 Bedienungsanleitung
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
MANUAL CARTON STAPLER
MODEL: H-1026
MANUAL
WARNING
Before operating this stapler familiarize yourself with the safety warnings and
instructions in this manual. Keep these instructions with the stapler for future
reference. If you have any questions, contact Uline at 1-800-295-5510.
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Table of Contents
Tool Specifications
Safety Instructions
Loading the Tool
Checking the Staple Leg Length
Clinch Adjustment
Depth Adjustment
Tool Operation
Clearing Tool Jams
Troubleshooting
Teeth Replacement
Driver Replacement
Pusher Spring Replacement
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Tool Specifications
Model of Tool H-1026
HDCS 19-35
Dimensions: LxHxW 15x11.5x4.5
Weight (without Fasteners) 3.75 lbs
Staple Specification: S-1396 C34 Stick
Staple Capacity: 100 pieces
Back to Top
SAFETY INSTRUCTIONS
1. Read the manual and understand all safety instructions before operating the tool.
If you have questions, contact Uline at 1-800-295-5510.
2. Always wear protective equipment, i.e. safety glasses, hearing protection and head
protection.
3. Do not place your hand or any other body part in the staple clinching area.
4. Never point the stapler at yourself or anyone else.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Loading the Tool
1. Pull the Pusher back until it stops on pusher pivots. Rotate pusher to position.
2. Insert up to 2 sticks of appropriate staples into the magazine. Let the sticks slide
forward to the front of the magazine.
3. Pull the pusher back to an upright position and gently let the pusher slide forward
against the staples. Do not let the pusher slide forward and strike the staples at
high speed as this may deform the staples and damage the tool.
Back to Top
Staple Leg Length
1. Loosen the set screw with a 3mm Allen wrench.
2. Turn adjusting rod 180°with a screw driver to the desired setting.
3. If you are using ¾” staples set L up.
4. If you are using 5/8” staples set S up. (diagram)
5. Tighten the set screw.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Clinch Adjustment
Loosen adjustment nut. Turn adjustment screw clockwise to loosen clinch. Turn
adjustment screw counter-clockwise to tighten clinch. After adjusting, tighten adjustment
nut.
Back to Top
Depth Adjustment
1. Loosen front screw with a 6mm Allen wrench.
2. Push the body up and adjust to the desired depth.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Operating Instructions
Warning
1. Insert the staples into the tool following the loading instructions.
2. Grasp the handle with one hand on box in line with the desired staple location.
There is a small projection on either side of the magazine seat as an aid in locating
the position of the staple.
3. The strongest closure requires staples close to the ends of the box.
Back to Top Clearing a Jam
1. Pull Pusher back and rotate to a locked position.
2. Insert needle nose pliers or screw driver to clear jam.
3. Slowly release Pusher back to position.
Back to Top
1. Protect your eyes and ears. Wear:
a. Safety glasses with side shields
b. hearing protection.
Ensure that anyone in the vicinity wears safety protection.
2. To prevent accidental injuries never place a hand or any other body part in the staple
clinching area or adjustment window.
3. Never point the stapler towards you or anyone else.
4. Always handle the stapler with care. Never pull the trigger unless tool is ready for
operation.
5. Check and replace any damaged or worn components on the stapler.
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Troubleshooting
Warning
Problem Cause Remedy
Excessive jams 1. Teeth screws loose.
2. Wrong staple size. 1. Tighten screws
2. Check staples
Uneven clinch 1. Wrong staple size. 1. Check for proper leg length
adjustment & clincher size.
Unclinched staple 1. Teeth are loose or broken.
1. Check & replace teeth as
needed.
Back to Top
Teeth Replacement
1. Loosen screws and nut with an 8mm spanner and 4mm Allen wrench.
2. Remove the magazine assembly.
3. Loosen screws with 3mm Allen wrench
4. Change teeth one at a time to prevent reverse teeth.
Back to Top
Stop using the tool immediately if any of the following problems occur. Serious
personal injury could occur. Any repairs or replacements must be done by a
qualified person or authorized service center only.
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Driver Replacement
1. Loosen screw and nut with a 8mm spanner wrench and a 4mm Allen wrench.
2. Remove the magazine assembly.
3. Loosen the set screw with a 3mm Allen wrench to unlock the adjusting rod.
4. Remove the linkage mechanism and adjusting rod simultaneously from the body.
5. Loosen the pivot screws with flat screwdriver. Remove handle and linkage
mechanism.
6. Remove the Spring Pin with a hammer and 5 mm straight rod.
7. Loosen screws with a 3mm allen wrench. Take off the spring pin with a hammer
and 6 mm straight rod.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Pusher Spring Replacement
1. Loosen the screws and nut with a 8mm Spanner wrench and a 4mm Allen wrench.
2. Remove the Magazine Assembly.
3. Pull the Pusher back until it stops on the rod, rotate the Pusher to position.
4. Push the magazine seat back and remove it from the magazine.
5. Loosen the screw and nut with a 2.5mm Allen wrench and 7mm socket wrench.
6. Loosen the Rod with a 6mm Offset wrench and remove the Pusher guides.
Remove the Pusher.
7. Remove the Spring Pin with a hammer and 4 mm straight rod.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
Inhaltsverzeichnis
Andere U-Line Elektrowerkzeuge Handbücher
U-Line
U-Line SWINGLINE H-3067 Bedienungsanleitung
U-Line
U-Line H-1440 Bedienungsanleitung
U-Line
U-Line H-1980 Bedienungsanleitung
U-Line
U-Line H-1024 Bedienungsanleitung
U-Line
U-Line H-10066 Bedienungsanleitung
U-Line
U-Line H-2027 Bedienungsanleitung
U-Line
U-Line H-1030 Bedienungsanleitung
U-Line
U-Line H-8094 Bedienungsanleitung
U-Line
U-Line H-995 Bedienungsanleitung
U-Line
U-Line H-1302 Bedienungsanleitung
U-Line
U-Line H-3070 Bedienungsanleitung
U-Line
U-Line SWINGLINE LIGHT TOUCH H-2323 Bedienungsanleitung
U-Line
U-Line H-1993 Bedienungsanleitung
U-Line
U-Line H-915 Bedienungsanleitung
U-Line
U-Line H-738 Bedienungsanleitung
U-Line
U-Line Shrinkfast 975 Bedienungsanleitung
U-Line
U-Line H-8094 Bedienungsanleitung
U-Line
U-Line Н-863 Bedienungsanleitung
U-Line
U-Line H-2027 Bedienungsanleitung
U-Line
U-Line H-491 Bedienungsanleitung
