U-Line Combo CO29 Bedienungsanleitung

www.U-LineService.com

Phone (414) 354-0300 • FAX (414) 354-7905

Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696

[email protected]

02/2005

CO29A and CO29FF

Ice Maker/Refrigerators

Installation Guide

www.U-LineService.com 202/2005

CO29A and CO29FF Ice Maker/Refrigerators

Contents

Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Door Swing/Clearances Information . . . . . . . . . . . . . . 4

Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . 6

Custom 1/4" Thick Door Panel Insert . . . . . . . . . . . . . . 7

Checking Door Alignment . . . . . . . . . . . . . . . . . . . . . . 8

Adjusting Door Alignment . . . . . . . . . . . . . . . . . . . . . . 8

Water Supply Connection . . . . . . . . . . . . . . . . . . . . . . . 8

Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 9

Leveling Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installation of the CO29A/CO29FF . . . . . . . . . . . . . . . . 10

Grille Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Glass Shelf Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installation Troubleshooting . . . . . . . . . . . . . . . . . . . . . 11

Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Start-Up Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 12

Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

IMPORTANT

PLEASE READ all instructions completely before

attempting to install or operate the unit.

• This unit requires connection to the water supply.

Improper hook-up can result in substantial property

damage! If you are unsure of your ability to safely

connect the water supply to the unit, consult a licensed

plumber for assistance.

• This unit requires connection to a grounded (three-

prong), polarized receptacle that has been placed by a

qualified electrician in accordance with applicable

electrical codes.

Safety Alert Definitions

Safety items throughout this guide are labeled with a

Danger, Warning or Caution based on the risk type:

DANGER

Danger means that failure to follow this safety

statement will result in severe personal injury or

death.

WARNING

Warning means that failure to follow this safety

statement could result in serious personal injury,

or death.

CAUTION

Caution means that failure to follow this safety statement

may result in minor or moderate personal injury, property

or equipment damage.

1 Follow Safety Precautions

02/2005 3www.U-LineService.com

CO29A and CO29FF Ice Maker/Refrigerators

General Precautions

Use this appliance for its intended purpose only and

follow these general precautions along with those listed

throughout this guide:

WARNING

SHOCK HAZARD — Electrical Grounding Required.

• Keep the unit unplugged throughout installation

except during testing.

• Never remove the round grounding prong from

the plug and never use a two-prong grounding

adapter.

• Never use an extension cord to connect power to

the unit.

• Always keep your working area dry.

CAUTION

• Use care when moving and handling the unit. Use

gloves to prevent personal injury from sharp edges.

• Do not lift the unit by the door or door handle.

• Do not install the unit behind closed doors or in any

way that would obstruct airflow to the front grille,

which may cause the unit to malfunction.

You have received a carton containing your CO29A or

CO29FF Ice Maker/Refrigerator with a package inside

containing a User Manual, a Product Registration Card

and water connection parts. Complete and mail the

Product Registration Card or register online at

www.U-LineService.com. Once your unit is installed, keep

the User Manual and this Installation Guide in a safe place

for future reference.

CO29A/CO29FF units are available in vinyl clad cabinets

with matching doors which have a slightly contoured

handle across the top and are reversible. The doors have

recessed front panels that will accept a custom 1/4 inch

thick door panel. Units have two tempered glass shelves.

Please carefully follow the directions that apply to your

unit and your intended design.

Tools/Materials Required

• Screwdrivers — slotted and Phillips head

• 1/4-inch OD copper tubing and shut-off valve for water

supply line

• 1/4-inch thick door panel material and cutting tools

Inspection

Unwrap and inspect the unit on a flat, level surface

capable of supporting its entire weight.

Exterior Cleaning

(As Required)

Black and White Models:

Black and white surfaces may be cleaned with a mild

detergent and warm water solution. Do not use solvent-

based or abrasive cleaners. Use a soft sponge and rinse

with clean water. Wipe with a soft, clean towel to prevent

water spotting.

2 Inspect and Plan

www.U-LineService.com 402/2005

CO29A and CO29FF Ice Maker/Refrigerators

Your U-Line product has been designed for either free-

standing or built-in installation. When built-in, your unit

does not require additional air space for top, sides or rear.

However, the front grille must NOT be obstructed and

clearance is required for water and electrical connections

in the rear.

Note: Unit can NOT be installed behind a closed cabinet

door.

Cut-Out Dimensions

Follow the cut-out drawing in Figure 1. The 21-1/16"

width allows 1/4" for ease in installation and removal of

the unit. 24" is the counter depth in most installations.

The unit is 24" deep including the door and handle (see

Figure 2).

IMPORTANT

It is extremely important that the unit sits on a level

surface, as it does not have feet levelers. If it is not level,

the ice mold will not fill evenly.

Product Dimensions

Door Swing/Clearances Information

Units have a zero clearance for the door to open

90° (see Figure 3). U-Line recommends a minimum door

clearance of 1/4" to accommodate the handle if the unit is

right-hand hinged and installed next to a wall or similar

type of structure.

Units require a minimum of 1" door clearance if installed

flush with cabinet or wall and 9" clearance if installed

adjacent to cabinet or wall if the unit is left-hand hinged

for easy removal of ice bin. See Figure 3.

3 Prepare Site

24"

Minimum

21-1/16"

See Electrical

Specifications

for Power Supply

Typical

Counter

Height

34-1/4"

35-1/8"

Cut-Out

Height

28-5/8"

28-7/8"

Filler Panel (Not Provided by U-Line) –

May Be Added Above or Below Unit

to Enclose for a Built-In Look

Figure 1

24"

Including

Handle

28-1/2"

20-13/16"

Figure 2

02/2005 5www.U-LineService.com

CO29A and CO29FF Ice Maker/Refrigerators

Reversing the Door

All units may be left- or right-hand opening.

Note: The grille should not yet be installed. If it has been

installed, remove it for door reversing. See Page 10.

To reverse the door:

1. Remove top hinge from cabinet (three screws). See

Figure 4. Hold door to keep it from falling.

2. Lift the door off the bottom hinge.

3. Remove bottom hinge from cabinet (two screws). See

Figure 5

. Remove screws on opposite side of cabinet

(

Figure 6

). Note that there may be a nut behind one or

both screws on either side.

4. Install hinge on opposite side, bottom of cabinet. See

Figure 7

. Replace nut on back side where installed.

Align hinge outer edge with cabinet before tightening

screws.

145°

Door Swing

Door

Swing

1/4" Min.

Wall

Left-Hand Hinge –

Flush with Cabinet or Wall

Left-Hand Hinge –

Adjacent to Cabinet or Wall

Wall or

Cabinet

Wall or Cabinet

Wall or

Cabinet

Wall or

Cabinet

90°

Door Swing

9”

Min.

1”

Min.

21-7/16"

22-3/8"

Right-Hand Hinge

Figure 3

Figure 4 Figure 5

Figure 6 Figure 7

www.U-LineService.com 602/2005

CO29A and CO29FF Ice Maker/Refrigerators

5. Relocate plastic spacer/

bushing on bottom of

door to opposite side,

and place door on

bottom hinge pin. See

Figure 8

. Clean out

bushing hole in door

bottom with a

screwdriver if necessary.

6. Remove plastic hole

plug from door handle

and relocate on

opposite side. See

Figure 9

7. Remove pivot screw from top hinge, invert screw and

reinstall pivot screw in top hinge. See

Figure 9

8. Remove three plastic

screw plugs from hinge

holes, top of cabinet,

opposite side. Be careful

not to scratch cabinet.

See

Figure 10

9. Place door on lower

hinge pin. Invert and

install upper hinge on

door.

10. Fasten upper hinge to

unit (three screws).

Partially tighten screws.

See

Figure 11

11. Adjust door to assure

proper seal. Tighten

upper and lower hinge

screws securely.

12. Replace three plastic

plugs removed in Step 8

into holes on top of

unit. Replace screws in

holes in bottom of unit

on opposite side.

Other Site Requirements

Power Supply

The unit requires a grounded and polarized 115 VAC,

60 Hz, 15A circuit (normal household current). See

Electrical Specifications on Page 9.

Water Supply

The unit requires a 1/4-inch OD water supply line and a

shut-off valve. For more information see Page 8.

Environmental Requirements

The surrounding air temperature must be at least 50°F

(10°C) but must not exceed 110°F (40°C). Units may be

installed outdoors in a covered area. The unit must not be

located near heat-generating equipment or in direct

sunlight.

Bushing

Figure 8

Plastic

Plug Hole

Plastic

Plug Hole

Hinge

Screw

Right Side

Door Swing

Right Side

Hinge

Invert

Screw

Invert

Hinge

Left Side

Door Swing

Figure 9

Figure 10

Figure 11

02/2005 7www.U-LineService.com

CO29A and CO29FF Ice Maker/Refrigerators

Units will accept a Custom 1/4" Thick Insert to harmonize

with or accent the surrounding decor.

If this treatment is not included in this installation, go on

to 5 Adjust Door.

Custom 1/4" Thick Door Panel Insert

Door Panel Preparation

A custom door panel can be inserted into the doorframe.

Custom door panels can be flat or raised, as long as the

maximum panel thickness where inserted into the door

reveal (channel) is 1/4"-thick. For raised panels, the depth

of the reveal is 1/4" on all four sides.

IMPORTANT

Raised panels will reduce the door’s 90° swing/zero

clearance if the unit is installed next to a wall or similar

type of structure (see Page 4).

Cut the panel insert to the following dimensions.

Custom 1/4" Dimensions:

Width: 19-13/16"

Height: 21-13/32"

The door panel must not weigh more than 20 lbs.

Door Panel Installation

Install the insert as follows:

CAUTION

Use care when handling the insert. Insert edges may be

sharp.

Remove top hinge screw pin with a Phillips head

screwdriver. Remove door by tilting forward and lifting

off bottom hinge pin.

2. Pull door gasket out of

groove (top edge of door

only). Start in the middle

and pull outward, moving

toward the edge (see

Figure 13

). This may take

some force.

3. Remove two outside

screws holding door

handle. Slightly separate

door handle from door

(see

Figure 14

4. Pull handle up and off.

5. Slide custom door panel insert into 1/4-inch channel in

door front.

6. Holding door gasket out of the way, replace handle on

door, making sure it is seated properly on insert and

that screw holes line up.

7. Install two small screws removed in

Step 3

8. Starting at the corners and working inward, push door

gasket into place on door.

9. Place door on bottom hinge pin and install upper hinge

screw.

10. Go on to

5 Adjust Door

4 Prepare and Install Door Panel

Figure 12 Figure 13

Figure 14

www.U-LineService.com 802/2005

CO29A and CO29FF Ice Maker/Refrigerators

Checking Door Alignment

The unit’s door is aligned at the factory before shipment.

However, its alignment could have been disturbed during

shipment or during door panel installation.

IMPORTANT

Properly aligned, the door's gasket should be firmly in

contact with the cabinet all the way around the door (no

gaps).

1. Carefully examine the door's gasket to assure that it is

firmly in contact with the cabinet.

Note: When inspecting door alignment, make sure the

door gasket is not pinched on the hinge side of the door.

2. If the door is properly aligned, go on to

6 Prepare

Plumbing

. If it is not, use the following procedure.

Adjusting Door Alignment

1. Loosen (do not remove)

top and bottom hinge

screws. See Figure 15.

2. Align door squarely with

cabinet. Make sure gasket

is firmly in contact with

cabinet all the way around

the door (no gaps).

3. Tighten bottom hinge

screws.

4. Tighten top hinge screws.

Go on to

6 Prepare

Plumbing

CAUTION

Plumbing installation must observe all state and local

codes. All water connections MUST BE made by a licensed/

qualified plumbing contractor. Failure to follow

recommendations and instructions may result in damage

and/or harm.

WARNING

To prevent accidental electrocution, make certain

that the floor surfaces surrounding the unit are

dry whenever power is removed from, or applied

to, the unit.

Water Supply Connection

When connecting the water supply, follow these

guidelines:

• Review the local plumbing codes before you install the

unit.

• Connect to the cold water supply.

• The water pressure should be between 20 and 120 psi.

• Install a shut-off valve in the 1/4 inch OD water supply

line.

• Connect sufficient tubing to the unit so that tubing

may be looped, allowing the unit to be removed for

cleaning and servicing (see Figure 18). However, make

certain that the tubing is not pinched or damaged

during installation.

• U-Line recommends the use of copper tubing for

installation.

To connect to water supply:

1. Install the 1/4 inch OD copper water line from the

main water source.

5 Adjust Door

Figure 15

6 Prepare Plumbing

02/2005 9www.U-LineService.com

CO29A and CO29FF Ice Maker/Refrigerators

2. Locate the compression fitting and ferrule packed with

the unit. Slide the compression fitting and ferrule over

the 1/4-inch OD water supply line. Do not use thread

sealing compound or tape. Using two wrenches,

tighten the compression fitting on the supply line (see

Figure 16).

3. Carefully bend the water supply line into position and

connect the line to the solenoid valve (see

Figure 17

Avoid kinking the water supply line.

IMPORTANT

Normal operation creates some vibration. A water supply

line contacting cabinet wall may cause excessive noise

during operation or damage to the line.

4. For recessed installations, allow extra water supply line

length to provide slack for easy removal from the

recessed area (see

Figure 18

). This will also safeguard

against kinking the line.

5. Go on to

7 Prepare Power Supply

Electrical Specifications

CAUTION

Electrical installation must observe all state and local

codes. This unit requires connection to a grounded (three-

prong), polarized receptacle that has been placed by a

qualified electrician.

The unit requires a grounded and polarized 115 VAC,

60 Hz, 15A power supply (normal household current).

An individual, properly grounded branch circuit or circuit

breaker is recommended. GFCI (ground fault circuit

interrupter) is usually not required for fixed location

appliances and is not recommended for your unit because

a GFCI could be prone to nuisance tripping. However, be

sure to consult your local codes.

See Figure 19 for recommended receptacle location.

WARNING

SHOCK HAZARD — Electrical Grounding Required.

• Never remove the round grounding prong from

the plug and never use a two-prong grounding

adapter.

• Never use an extension cord to connect power to

the unit.

Go on to 8 Level the Unit.

Water

Connection

Figure 17Figure 16

Figure 18

7 Prepare Power Supply

24"

Minimum

1-1/2"

Figure 19

www.U-LineService.com 10 02/2005

CO29A and CO29FF Ice Maker/Refrigerators

Leveling Information

IMPORTANT

It is extremely important that the unit sits on a level

surface, as it does not have feet levelers. If it is not level,

the ice mold will not fill evenly.

Use a level to check the

levelness of the unit from

front to back and from side

to side. Level should be

placed along top edge and

side edge as shown (see

Figure 20). Go on to

9 Install the Unit.

Installation of the CO29A/CO29FF

1. Open the water supply valve in the main water source.

2. Plug in the power cord.

3. Gently push the unit into position. Be careful not to

kink the water supply line or entangle the electrical

cord.

4. Re-check the leveling, from front to back and side to

side. Make any necessary adjustments. The unit’s top

surface should be approximately 1/8" below the

countertop.

Grille Installation

1. Locate and remove the grille screw from the cabinet,

using a standard blade screwdriver (or a 1/4"

nutdriver). See Figure 21

2. Remove the control knob by pulling it away from the

cabinet.

3. Identify the grille screw hole on the grille itself. It is

located toward the top of the middle recessed section

of the grille.

4. Place the two hook-hinges (located on the rear bottom

side of the grille) onto the front lip of the unit base.

Swing the grille up into position, aligning the grille

screw hole on the grille to the grille screw hole on the

cabinet. See

Figure 22

8 Level the Unit

Check

Level

Figure 20

9 Install the Unit

Grille Screw

Figure 21

Andere Handbücher für Combo CO29

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere U-Line Kühlschrank Handbücher

U-Line

U-Line U-ADA24R13B Installationshandbuch

U-Line

U-Line 2175WC Bedienungsanleitung

U-Line

U-Line UHRE124-SS01A Installationshandbuch

U-Line

U-Line 1000 SERIES Installationshandbuch

U-Line

U-Line CLRCO2175 Bedienungsanleitung

U-Line

U-Line 3036RR Bedienungsanleitung

U-Line

U-Line 1115R Bedienungsanleitung

U-Line

U-Line 2175DWRR Bedienungsanleitung

U-Line

U-Line U-3036RRS-00B Bedienungsanleitung

U-Line

U-Line Wine Captain UHWD524IS01A Installationshandbuch

U-Line

U-Line UHRI124BS01A Installationshandbuch

U-Line

U-Line UHRI124-SS01A Installationshandbuch

U-Line

U-Line 2175R Betriebsanleitung

U-Line

U-Line 1224R Bedienungsanleitung

U-Line

U-Line UHRE124-SG81A Installationshandbuch

U-Line

U-Line 2224R Bedienungsanleitung

U-Line

U-Line UHWC524SG41AU Installationshandbuch

U-Line

U-Line Origins 75R Bedienungsanleitung

U-Line

U-Line U-1224RSOD-00B Installationshandbuch

U-Line

U-Line pmn Bedienungsanleitung

U-Line

U-Line U-1224FZRINT-00A Installationshandbuch

U-Line

U-Line WINE CAPTAIN 2115R Bedienungsanleitung

U-Line

U-Line U-2245RINT-00B Installationshandbuch

U-Line

U-Line U-ss01a Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung