Ubee DVW324 Einrichtungshandbuch

DVW324 D3.0 Advanced Wireless Voice Gateway Safety and Installation Product Insert

◆ Federal Communications Commission

(FCC) Interference Statement

This device has been tested and found to comply

with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

device generates, uses, and can radiate radio

frequency energy. If not installed and used in

accordance with the instructions, the device may

cause harmful interference to radio communications.

There is no guarantee, however, that interference

will not occur in a particular installation. If this device

causes harmful interference to radio or television

reception, which can be determined by turning it off

and on, the user can try to correct the interference

by one of the following measures:

•Increase the separation between the device and

the equipment with which it is interfering (for

example, a television or radio).

•Connect the device to an electrical outlet on a

different circuit than the interfered device is

connected.

•Consult the dealer or an experienced radio/TV

technician for help.

◆ FCC Regulatory Information

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference

received, including interference that may cause

undesired operation. (3) There are two statements

for this product:

•Only the type of Metal PIFA antenna tested may

be used.

•The device must carry a label stating “FCC ID:

XCNDVW324.”

FCC Caution: Any changes or modifications not

expressly approved by the party responsible for

compliance could void the user's authority to operate

this device.

IEEE 802.11b or 802.11g operation of this device in

the U.S.A. is firmware-limited to channels 1 through

11.

For operation within 5.15 ~ 5.25GHz frequency

range, it is restricted to indoor environment. This

device meets all the other requirements specified in

Part 15E, Section 15.407 of the FCC Rules.

◆ FCC Radiation Exposure Statement

This device complies with FCC radiation exposure

limits set forth for an uncontrolled environment. This

device should be installed and operated at a

minimum distance of 20 cm between itself and your

body.

This device must not be co-located or operating in

conjunction with any other antenna or transmitter.

◆ Safety Notices

Read these instructions carefully before operating

the device. It is important to be aware of these safety

instructions. Install the device according to these

instructions and keep this guide for future reference.

•Do not use this device in a humid space, in the

rain, or near splashing water.

•Do not install during thunder or lightening storms.

•Do not cover any ventilation openings in the

device case.

•Do not place the device near heat sources such

as radiators or stoves.

•Clean the device only with a clean, dry cloth. Do

not use liquid or chemical cleaners.

•Avoid static discharge when touching the device

by first touching the coaxial connector of the

coaxial cable.

•The cable distribution system must be grounded

in accordance with ANSI/NFPA 70 and the

National Electrical Code (NEC), in particular

section 802.93, Grounding of the Outer

Conductive Shield of a Coaxial Cable.

◆ Installation Instructions

Use the following guidelines to install the device.

•For table mounting, place the device horizontally

on a stable surface.

•For wall mounting, use the mounting holes on the

bottom of the device, as shown in Figure 1.

Fasten two screws horizontally to the wall at a

distance of 19.4 cm (7.63”). Allow screws to

project from the wall so the device hangs securely

on the screws. See Figure 2 for recommended

screw size (D=5.0-5.5, H=1.8-2.2, L=8.2-9.0,

E=2.9-3.0).

Figure 1. Distance Between Mounting Holes

Figure 2: Screw Size

•Place the device near an outlet so the AC power

adapter can be plugged in directly to the wall

outlet without an extension. Observe the

maximum load of the electrical outlet. Please only

use the power adapter provided with the unit.

To install the device:

Connect the device according to the installation

instructions in Figure 3.

1. Connect one end of the RF coaxial cable (not

included) to the RF port on the device. Connect

the other end to the cable wall outlet or a cable

splitter. (Use a cable splitter, not included, to

connect the device and a television to the same

cable wall outlet.) Be sure not to bend or over

tighten the cables as this may strain the

connector and cause damage.

Figure 3: Connection Diagram

2. Connect one end of the Ethernet cable (included)

to one of the Ethernet ports (ETH1 – ETH4) on

the device. Connect the other end to the Ethernet

port on a PC. Note: Use Category 5e or 6 cables

with RJ45 connectors when connecting Ethernet

devices to the LAN ports. This ensures Gigabit

Ethernet speeds when the computer supports it.

3. Connect one end of an RJ11 phone cable to the

telephone port (TEL1, TEL2) on the device that

has been provisioned for voice service as

specified by the service provider. Connect the

other end to the phone port of the telephone.

Note: Telephone service will not be available if

voice service has not been provisioned through

the service provider.

4. Connect the power adapter to the POWER port

on the device. Plug the other end of the power

adapter into the AC wall outlet. Important: Use

only the power adapter that is shipped with the

device.

◆ Additional Rear Panel Buttons

•RESET button: To reset the device to the factory

defaults, insert a small object into the small, reset

opening and hold for more than 10 seconds. The

device resets to factory defaults and reboots.

Note: Not all parameters are reset to factory

defaults. Refer to the user guide for more

information.

•USB Ports: One USB port with host controller is

available.

•WPS (on the side of the device): The Wi-Fi

Protected Setup (WPS) method used to connect

PIN-protected Wi-Fi equipment to this device.

◆ LEDs on Front Panel

The following table describes LED behavior.

LED COLOR DESCRIPTION

PWR Green

LED remains on when device

has completed internal power‐on

tests successfully. LED blinks if

power‐on test fails.

DS Green

Blue

LED blinks during firmware

upgrade. LED is on when device

has locked to downstream

channel.

•Green - one channel bonded.

LED COLOR DESCRIPTION

•

Blue - more than one channel

bonded.

US Green

Blue

LED blinks during firmware

upgrade. LED is on when device

has locked to upstream channel.

•Green - one channel bonded.

•Blue - more than one channel

bonded.

RDY Green

LED blinks when obtaining IP

address and configuration file

and remains on when

successful.

Tel1/Tel2 Green

LED is on when telephone is on-

hook. LED blinks when

telephone is off-hook and during

firmware upgrade.

WLAN Green LED is on when connected and

blinks when traffic is passed.

WPS Green

LED blinks for 4 minutes after

WPS button is pushed until PIN

is entered from a wireless client.

LED remains on for 5 minutes

when client is connected, and

then turns off.

ETH1 –

ETH4 Green

Blue

LED is on with connectivity

between Ethernet port on the

device and Ethernet port on the

PC. LED blinks when traffic is

passed.

•Green indicates 10/100

Ethernet connection.

•Blue indicates 1000 Ethernet

connection.

USB Green LED is green when a USB

device is connected and blinks

when data is passed.

Figure 4: Front Panel LEDs

Inhaltsverzeichnis

Andere Ubee Tor Handbücher

Ubee

Ubee DVW32CB Bedienungsanleitung

Ubee

Ubee DVW328 Einrichtungshandbuch

Ubee

Ubee DDW36C Bedienungsanleitung

Ubee

Ubee UBC1329AA00 Bedienungsanleitung

Ubee

Ubee DDW3611 Bedienungsanleitung

Ubee

Ubee DDW3611 Bedienungsanleitung

Ubee

Ubee DDW366 Einrichtungshandbuch

Ubee

Ubee DDW366 Bedienungsanleitung

Ubee

Ubee DDW36C Bedienungsanleitung

Ubee

Ubee UBC1301-AA00 Bedienungsanleitung

Ubee

Ubee DDW365 Bedienungsanleitung

Ubee

Ubee UBC1310BA10 Bedienungsanleitung

Ubee

Ubee DVW325 Bedienungsanleitung

Ubee

Ubee DVW326 Bedienungsanleitung

Ubee

Ubee DVW326B Einrichtungshandbuch

Ubee

Ubee DVW32G6 Einrichtungshandbuch

Ubee

Ubee DVW32CB Bedienungsanleitung

Ubee

Ubee UBC1301-AA00 Bedienungsanleitung

Ubee

Ubee DVW3201B Bedienungsanleitung

Ubee

Ubee UBC1330AAOO Bedienungsanleitung

Ubee

Ubee UBC1303 Bedienungsanleitung

Ubee

Ubee DDW36C Bedienungsanleitung

Ubee

Ubee EVW32C Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung