Ublox C101-D9C Bedienungsanleitung

UBX-21009111 - R02

C1-Public www.u-blox.com

C101-D9C

Application board (rev. C)

User guide

Abstract

This document explains the use of C101-D9C application board. The C101-D9C board enables

customers to evaluate QZSS L6 correction services with the NEO-D9C correction data receiver.

C101-D9C - User guide

UBX-21009111 - R02 Document information Page 2 of 17

C1-Public

Document information

Title C101-D9C

Subtitle Application board (rev. C)

Document type User guide

Document number UBX-21009111

Revision and date R02 17-Jan-2022

Disclosure restriction C1-Public

This document applies to the following products:

Product name Type number Firmware version PCN reference

C101-D9C C101-D9C-0-00 FW QZS 1.01 N/A

u-blox or third parties may hold intellectual property rights in the products, names, logos and designs included in this

document. Copying, reproduction, modification or disclosure to third parties of this document or any part thereof is only

permitted with the express written permission of u

-blox.

The information contained herein is provided “as is” and u

-blox assumes no liability for its use. No warranty, either express or

implied, is given, including but not limited

to, with respect to the accuracy, correctness, reliability and fitness for a particular

purpose of the information. This document may be revised by u

-blox at any time without notice. For the most recent

documents, visit www.u

-blox.com.

-blox AG.

C101-D9C - User guide

UBX-21009111 - R02 Contents Page 3 of 17

C1-Public

Contents

Document information .............................................................................................................................2

Contents .......................................................................................................................................................3

1Introduction ..........................................................................................................................................4

1.1 Package contents .......................................................................................................................................4

2C101-D9C product overview............................................................................................................5

2.1 Components.................................................................................................................................................5

2.2 Jumpers........................................................................................................................................................6

3C101-D9C standalone operation....................................................................................................7

4C101-D9C operation with C099-F9P.............................................................................................9

4.1 C101-D9C/C099-F9P via Arduino shield..............................................................................................10

Appendix .................................................................................................................................................... 12

AGlossary .............................................................................................................................................. 12

BAntenna specification (L1/L2/E5b/L6)...................................................................................... 12

CC101-D9C schematics.................................................................................................................... 13

Related documentation......................................................................................................................... 16

Revision history ....................................................................................................................................... 16

Contact....................................................................................................................................................... 17

C101-D9C - User guide

UBX-21009111 - R02 Introduction Page 4 of 17

C1-Public

1Introduction

The C101-D9C board is a convenient tool that allows customers to become familiar with the u-blox

NEO-D9C QZSS L6 receiver. The board provides facilities for evaluating the product and

demonstrating its key features.

NEO-D9C is a QZSS L6 receiver that brings QZSS Centimeter Level Augmentation Service (CLAS)

support to u-blox GNSS modules, enabling centimeter-level navigation. The receiver can also track

the experimental MADOCA service transmitted on the QZSS L6 signal.

The C101-D9C application board offers:

•NEO-D9C module for use as QZSS L6 correction data receiver

•USB connection for communication and power supply

•L6 antenna connection for receiving the satellite data stream

•Arduino shield connection

1.1 Package contents

The delivered package contains:

•C101-D9C board

•Multiband antenna (L1/L2/E5b/L6)

•Antenna ground plane (12 cm circular)

•USB interconnect cable

•Jumper connectors

Prior to using the board, it is useful to download the appropriate evaluation software and keep handy

the documents listed in the Related documents section.

C101-D9C - User guide

UBX-21009111 - R02 C101-D9C product overview Page 5 of 17

C1-Public

2C101-D9C product overview

2.1 Components

C101-D9C houses the NEO-D9C QZSS L6 receiver. The board is powered from the USB cable

connection or via Arduino shield. The main components of the board are listed below and shown in

Figure 1 and Figure 2:

•Native USB port

•FTDI USB bridge

•SMA RF connector and antenna supply capability (L-band)

•UART2 interface through Arduino shield

•NEO-D9C RESET button

•NEO-D9C SAFEBOOT button

Figure 1: C101-D9C block diagram

C101-D9C - User guide

UBX-21009111 - R02 C101-D9C product overview Page 6 of 17

C1-Public

Figure 2: C101-D9C quick start basic overview

2.2 Jumpers

The board is delivered with the following default jumpers:

•J6: This jumper provides 3.3 V power supply to an external active antenna plugged to the SMA RF

connector. The current limit circuit is also enabled up to 60 mA.

•J8: This jumper switches the communication from the UART2 of the NEO-D9C to the UART1 or

UART2 of the C099-F9P, when connected via the Arduino shield (refer to section 4.1 for further

details).

Figure 3: C101-D9C jumpers overview

For further details, see the C101-D9C schematic in Appendix C.

C101-D9C - User guide

UBX-21009111 - R02 C101-D9C standalone operation Page 7 of 17

C1-Public

3C101-D9C standalone operation

This section provides some quicksteps to enable NEO-D9C standalone operation and connecting via

u-center (see u-center user guide [3]).

•Connect the supplied L6 band antenna to the RF SMA connector.

•Connect the USB to a Windows PC, this will power the board. The FTDI and USB drivers will be

installed automatically from Windows Update when you connect the board for the first time.

•The power LED will turn on in blue color.

•Start the Device Manager utility from Windows. Two new ports will be visible under the Ports tab:

the USB Serial Device is the Native USB port and the USB Serial Port is the FTDI USB bridge port,

as shown in Figure 5.

Figure 4: Windows Device Manager Ports identifications

Figure 5: FTDI USB bridge and USB ports properties

•Start u-center and connect to one of the COM ports. If you are using the FTDI USB bridge, make

sure the baud rate in u-center is set to 9600.

•Poll UBX-MON-VER message and check the content as shown in Figure 6 .

Figure 6: UBX-MON-VER message

C101-D9C - User guide

UBX-21009111 - R02 C101-D9C standalone operation Page 8 of 17

C1-Public

•Poll or enable the UBX-RXM-QZSSL6 message to check the received correction data.

Figure 7: UBX-RXM-QZSSL6 message

For further details regarding the UBX-RXM-QZSSL6 message, see the related Interface description

[4].

C101-D9C - User guide

UBX-21009111 - R02 C101-D9C operation with C099-F9P Page 9 of 17

C1-Public

4C101-D9C operation with C099-F9P

It is possible to use the C101-D9C board together with C099-F9P. Figure 9 shows how to interface

the C101-D9C board with the C099-F9P board. Two types of connections are available:

•USB interface (through PC)

•Arduino shield interface (UART2 direct connection)

When the USB connection is used, the corrections are provided through the host computer. Security

checks and data conversion are the responsibility of the user application, as well as the forwarding of

the corrections to the ZED-F9P.

Figure 8: C101-D9C - C099-F9P interfacing scheme

The provided multiband antenna can be used in combination for ZED-F9P and NEO-D9C, RF signal

splitter is needed. For further details, see the antenna specification in Appendix B.

C101-D9C - User guide

UBX-21009111 - R02 C101-D9C operation with C099-F9P Page 10 of 17

C1-Public

4.1 C101-D9C/C099-F9P via Arduino shield

Figure 9 shows the placement of the Arduino connectors on the C101-D9C board and Figure 10 shows

how to physically connect the C099-F9P board to the C101-D9C board via the Arduino shield. Jumper

J18 on the C099 board is needed for the ZED-F9P to receive the correction data on UART1 port. See

the C099 application board User guide [5] for further details.

Figure 9: C101-D9C Arduino connectors

Figure 10: Connecting C101-D9C to C099-F9P

Inhaltsverzeichnis

Andere Ublox Steuereinheit Handbücher

Ublox

Ublox ZED-F9P Bedienungsanleitung

Ublox

Ublox ZED-F9P Gebrauchs- und Pflegehandbuch

Ublox

Ublox C94-M8P Bedienungsanleitung

Ublox

Ublox TIM-5H Kurzanleitung zur Einrichtung

Ublox

Ublox NINA-B2 series Kurzanleitung zur Einrichtung

Ublox

Ublox NORA-W2 Series Kurzanleitung zur Einrichtung

Ublox

Ublox NEO-M8N Kurzanleitung zur Einrichtung

Ublox

Ublox NINA-B31 Series Bedienungsanleitung

Ublox

Ublox Fastrax IT500 Series Bedienungsanleitung

Ublox

Ublox M8 Series Kurzanleitung zur Einrichtung

Ublox

Ublox LISA-U100 Gebrauchs- und Pflegehandbuch

Ublox

Ublox NORA-B1 Series Kurzanleitung zur Einrichtung

Ublox

Ublox EVK-W16 Bedienungsanleitung

Ublox

Ublox NEO-M8P-2 Kurzanleitung zur Einrichtung

Ublox

Ublox ZED-F9H Gebrauchs- und Pflegehandbuch

Ublox

Ublox EVK-NORA-B1 Bedienungsanleitung

Ublox

Ublox EVK-MAYA-W1 Bedienungsanleitung

Ublox

Ublox NINA-B112 Kurzanleitung zur Einrichtung

Ublox

Ublox SARA-N2 Series Kurzanleitung zur Einrichtung

Ublox

Ublox LEA-M8S Kurzanleitung zur Einrichtung

Ublox

Ublox ZOE-M8B Series Kurzanleitung zur Einrichtung

Ublox

Ublox ZED-F9K Gebrauchs- und Pflegehandbuch

Ublox

Ublox NEO-6 Gebrauchs- und Pflegehandbuch

Ublox

Ublox NINA-B1 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung