Ublox Fastrax IT500 Series Bedienungsanleitung

NMEA Manual based on MediaTek

chipset

For u-blox, Fastrax IT500 series GPS/GNSS modules

Manual

Abstract

This document provides NMEA command manual for u-blox, Fastrax

IT500 series GPS/GNSS modules based on MediaTek chipset. This

NMEA command manual serves as a reference tool.

locate, communicate, accelerate

www.u-blox.com

NMEA Manual based on MediaTek chipset - Manual

FTX-HW-13002-A

Page 2 of 39

Document Information

Title NMEA Manual based on MediaTek chipset

Subtitle For u-blox, Fastrax IT500 series GPS/GNSS modules

Document type Manual

Document number FTX-HW-13002-A

Document status Preliminary

Document status information

Objective

Specification

This document contains target values. Revised and supplementary data will be published

later.

Advance

Information

This document contains data based on early testing. Revised and supplementary data will

be published later.

Preliminary This document contains data from product verification. Revised and supplementary data

may be published later.

Released This document contains the final product specification.

This document applies to the following products:

Name ROM/FLASH version PCN reference

IT530M Flash N/A

IT530 Flash N/A

UC530M Flash N/A

UC530 Flash N/A

UP501 Flash N/A

UP501B Flash N/A

UP501D Flash N/A

UP501R Flash N/A

IT520 Flash N/A

IT500 Flash N/A

This document and the use of any information contained therein, is subject to the acceptance of the u-blox terms and conditions. They

can be downloaded from www.u-blox.com.

u-blox makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make

changes to specifications and product descriptions at any time without notice.

u-blox reserves all rights to this document and the information contained herein. Reproduction, use or disclosure to third parties without

u-blox®is a registered trademark of u-blox Holding AG in the EU and other countries.

NMEA Manual based on MediaTek chipset - Manual

FTX-HW-13002-A Preliminary

Page 3 of 39

Contents

Contents..............................................................................................................................3

1NMEA default output messages..................................................................................5

1.1 GGA - Global Positioning System Fix Data ............................................................................................ 5

1.2 GLL – Geographic Position – Latitude/Longitude ................................................................................... 5

1.5 RMC - Recommended Minimum Specific GNSS Data. ........................................................................... 6

1.6 GSV - Satellites in view ......................................................................................................................... 6

1.7 GSA - DOP and Active Satellites............................................................................................................ 7

1.8 VTG – Course Over Ground and Ground Speed.................................................................................... 8

1.9 ZDA – Time and Date............................................................................................................................ 8

2NMEA commands .........................................................................................................9

2.1 PMTK000 TEST ................................................................................................................................... 10

2.2 PMTK001 ACK ................................................................................................................................... 10

2.3 PMTK010 Startup message................................................................................................................. 11

2.4 PMTK011 Output System Text ............................................................................................................ 11

2.5 PMTK101 CMD HOT START................................................................................................................ 11

2.6 PMTK102 CMD WARM START ........................................................................................................... 11

2.7 PMTK103 CMD COLD START ............................................................................................................. 12

2.8 PMTK104 CMD FULL COLD START ..................................................................................................... 12

2.9 PMTK120 CLEAR FLASH AID............................................................................................................... 12

2.10 PMTK127 CLEAR EPO FILE .................................................................................................................. 12

2.11 PMTK161 ENTER STANDBY MODE ..................................................................................................... 13

2.12 PMTK183 LOCUS QUERY LOGGING STATUS ...................................................................................... 13

2.13 PMTK184 LOCUS ERASE FLASH.......................................................................................................... 14

2.14 PMTK185 LOCUS START/STOP LOGGER ............................................................................................. 14

2.15 PMTK186 LOCUS LOG NOW .............................................................................................................. 14

2.16 PMTK622 LOCUS QUERY DATA ......................................................................................................... 15

2.17 PMTK869 ENABLE EASY ..................................................................................................................... 16

2.18 PMTK220 SET POS FIX ........................................................................................................................ 16

2.19 PMTK223 SET ALWAYS LOCATE DEFAULT CONFIGURATION ............................................................. 17

2.20 PMTK225 SET PERIODIC MODE .......................................................................................................... 17

2.21 PMTK251 SET NMEA BAUD RATE....................................................................................................... 18

2.21.1 Setting 5 Hz navigation ............................................................................................................... 19

2.21.2 Setting 10 Hz navigation ............................................................................................................. 19

2.22 PMTK286 ENABLE AIC........................................................................................................................ 19

2.23 PMTK300 Set Fix Interval .................................................................................................................... 20

2.24 PMTK301 API SET DGPS MODE .......................................................................................................... 20

2.25 PMTK313 API SET SBAS ENABLED ...................................................................................................... 20

2.26 PMTK314 API SET NMEA OUTPUT ...................................................................................................... 21

2.27 PMTK330 API SET DATUM.................................................................................................................. 22

NMEA Manual based on MediaTek chipset - Manual

FTX-HW-13002-A Preliminary

Page 4 of 39

2.28 PMTK331 API SET DATUM ADVANCE................................................................................................. 22

2.29 PMTK335 API SET RTC TIME ............................................................................................................... 23

2.30 PMTK351 SET QZSS NMEA FORMAT .................................................................................................. 23

2.31 PMTK352 SET QZSS SUPPORT............................................................................................................. 23

2.32 PMTK353 API SET GNSS SEARCH MODE ............................................................................................ 24

2.33 PMTK386 API SET STATIC NAV THD MT333X..................................................................................... 24

2.34 PMTK397 API SET STATIC NAV THD MT332X..................................................................................... 25

2.35 PMTK390 API SET USER OPTION......................................................................................................... 25

2.35.1 Setting 4800 baud rate permanently ........................................................................................... 26

2.36 PMTK740 SET UTC TIME..................................................................................................................... 26

2.37 PMTK741 SET INITIAL POSITION AND TIME......................................................................................... 26

3Query commands .......................................................................................................28

3.1 PMTK400 API Q FIX CTL ..................................................................................................................... 28

3.2 PMTK401 API Q DGPS MODE ............................................................................................................. 28

3.3 PMTK413 API Q SBAS ENABLED ......................................................................................................... 28

3.4 PMTK414 API Q NMEA OUTPUT ......................................................................................................... 28

3.5 PMTK430 API Q DATUM .................................................................................................................... 29

3.6 PMTK431 API Q DATUM ADVANCE ................................................................................................... 29

3.7 PMTK490 API GET USER OPTION........................................................................................................ 29

4Firmware STATUS.......................................................................................................30

4.1 PMTK605 QUERY FIRMWARE INFO..................................................................................................... 30

4.2 PMTK607 QUERY EPO STATUS ........................................................................................................... 30

4.3 PMTK660 Q AVAILABLE SV EPH ......................................................................................................... 30

4.4 PMTK661 Q AVAILABLE SV ALM ........................................................................................................ 31

5FIX Valid Flag ..............................................................................................................32

6Appendix A.................................................................................................................33

Table 1: Map datums........................................................................................................37

Related documents...........................................................................................................37

Revision history................................................................................................................38

Contact..............................................................................................................................39

NMEA Manual based on MediaTek chipset - Manual

FTX-HW-13002-A Preliminary

Page 5 of 39

1NMEA default output messages

IT500 series receivers support standard NMEA0183 messages.

In the default configuration, output messages are GGA, RMC, GSV and GSA messages. The receiver can be

configured to have a user defined set of output messages, by command PMTK314 as described in chapter 2.12.

Output messages are utilized in Fastrax Workbench 5 to visualize the GPS/GNSS data. Default output messages

cover most of the applications.

1.1 GGA - Global Positioning System Fix Data

Time, position and fix related data for a GPS receiver.

Example:

$GPGGA,114353.000,6016.3245,N,02458.3270,E,1,10,0.81,35.2,M,19.5,M,,*50

Format:

$GPGGA,hhmmss.dd,xxmm.dddd,<N|S>,yyymm.dddd,<E|W>,v,ss,d.d,h.h,M,g.g,M,a.a,xxxx*hh<CR><LF>

Type Description

hhmmss.dd UTC time of the fix.

hh=hours; mm=minutes; ss=seconds; dd=decimal part of seconds

xxmm.dddd Latitude coordinate.

xx=degrees; mm=minutes; dddd=decimal part of minutes

<N/S> Character denoting either N=North or S=South.

yyymm.dddd Longitude coordinate.

yyy=degrees; mm=minutes; dddd=decimal part of minutes

<E/W> Character denoting either E=East or W=West.

v Fix valid indicator

1 = GPS fix (SPS)

2 = DGPS fix

3 = PPS fix

4 = Real Time Kinematic

5 = Float RTK

6 = estimated (dead reckoning) (2.3 feature)

7 = Manual input mode

8 = Simulation mode

ss Number of satellites used in position fix, 00-12. Notice: Fixed length field of two letters.

d.d HDOP - Horizontal Dilution Of Precision.

h.h Altitude (mean-sea-level, geoid)

MLetter M.

g.g Difference between the WGS-84 reference ellipsoid surface and the mean-sea-level altitude.

MLetter M.

a.a -

xxxx -

1.2 GLL – Geographic Position – Latitude/Longitude

Latitude and Longitude, UTC time of fix and status.

Example:

$GPGLL,6012.5674,N,02449.6545,E,072022.000,A,A*50

Format:

$GPGLL,xxmm.dddd,<N|S>,yyymm.dddd,<E|W>,hhmmss.ddd,S,M*hh<CR><LF>

NMEA Manual based on MediaTek chipset - Manual

FTX-HW-13002-A Preliminary

Page 6 of 39

Type Description

xxmm.dddd Latitude coordinate.

xx=degrees; mm=minutes; dddd=decimal part of minutes

<N|S> Character denoting either N=North or S=South.

yyymm.dddd Longitude coordinate.

yyy=degrees; mm=minutes; dddd=decimal part of minutes

<E|W> Character denoting either E=East or W=West.

hhmmss.ddd UTC time of the fix.

hh=hours; mm=minutes; ss=seconds; ddd=decimal part of seconds

S Status indicator.

A=valid; V=invalid

M Mode indicator.

A=autonomous; N=data not valid

1.5 RMC - Recommended Minimum Specific GNSS Data.

Time, date, position, course and speed data.

Message start as “$GNRMC” in IT530M default mode both GPS and Glonass constellation.

Example:

$GPRMC,114353.000,A,6016.3245,N,02458.3270,E,0.01,0.00,121009,,,A*69

Example IT530M hybrid mode:

$GNRMC,105440.000,A,6012.5669,N,02449.6536,E,0.00,0.00,061112,,,D*70

Format:

$GPRMC,hhmmss.dd,S,xxmm.dddd,<N|S>,yyymm.dddd,<E|W>,s.s,h.h,ddmmyy,d.d, <E|W>,M*hh<CR><LF>

Type Description

hhmmss.dd UTC time of the fix.

hh=hours; mm=minutes; ss=seconds; dd=decimal part of seconds

S Status indicator.

A=valid; V=invalid

xxmm.dddd Latitude coordinate.

xx=degrees; mm=minutes; dddd=decimal part of minutes

<N|S> Character denoting either N=North or S=South.

yyymm.dddd Longitude coordinate.

yyy=degrees; mm=minutes; dddd=decimal part of minutes

<E|W> Character denoting either E=East or W=West.

s.s

Speed in knots.

h.h

Heading

ddmmyy UTC Date of the fix.

dd=day of month; mm=month; yy=year

d.d

Magnetic variation in degrees, not supported

<E|W>

Letter denoting direction of magnetic variation. Either E=East or W=West. Not supported

M Mode indicator

A=autonomous; N=data not valid

1.6 GSV - Satellites in view

Number of satellites in view, satellite ID (PRN) numbers, elevation, azimuth and SNR value. The information for

four satellites is a maximum per one message, additional messages up to maximum of eight are sent if needed.

The satellites are in PRN number order.

NMEA Manual based on MediaTek chipset - Manual

FTX-HW-13002-A Preliminary

Page 7 of 39

Message starting with “$GNGSV” will be output in IT530M default mode, including both GPS and

Glonass constellation satellite data.

Example:

$GPGSV,3,1,11,29,68,228,47,30,59,151,47,31,44,284,45,02,38,062,44*7C

$GPGSV,3,2,11,12,28,130,41,10,14,102,35,05,12,110,35,04,11,040,34*70

$GPGSV,3,3,11,21,05,196,29,16,05,297,28,13,02,021,30*4E

Format:

$GPGSV,n,m,ss,xx,ee,aaa,cn,…………. ,xx,ee,aaa,cn*hh<CR><LF>

Type Description

Total number of messages, 1 to 9

Message number, 1 to 9

Total number of satellites in view

Satellite ID (PRN) number

Satellite elevation, degrees 90 max

aaa

Satellite azimuth, degrees True, 000 to 359

ch Signal-to-noise ration (C/No) 00-99 dB-Hz. Value of zero means that the satellite is predicted to

be on the visible sky but it isn't being tracked.

1.7 GSA - DOP and Active Satellites

GPS receiver operating mode, satellites used in the navigation solution reported by the GGA sentence, and DOP

values.

Message starting with “$GNGSA” will be output in IT530M default mode including both GPS and

Glonass constellation satellite data.

Example:

$GPGSA,A,3,02,21,30,04,16,05,10,12,31,29,,,1.33,0.81,1.06*02

Example IT530M hybrid mode:

$GNGSA,A,3,26,21,16,22,18,06,19,15,30,03,07,08,1.03,0.55,0.87*1D

$GNGSA,A,3,78,71,80,86,65,79,88,87,72,,,,1.03,0.55,0.87*19

Format:

$GPGSA,a,b,xx,xx,xx,xx,xx,xx,xx,xx,xx,xx,xx,xx,p.p,h.h,v.v*hh<CR><LF>

Type

Description

Mode:

M = Manual, forced to operate in 2D or 3D mode.

A = Automatic, allowed to automatically switch 2D/3D.

Mode:

1 = Fix not available,

2 = 2D,

3 = 3D

ID (PRN) numbers of GPS satellites used in solution

p.p

PDOP

h.h

HDOP

v.v VDOP

NMEA Manual based on MediaTek chipset - Manual

FTX-HW-13002-A Preliminary

Page 8 of 39

1.8 VTG – Course Over Ground and Ground Speed

Course and speed.

Example:

$GPVTG,0.00,T,,M,0.00,N,0.00,K,A*3D

Format:

$GPVTG,h.hh,T,m.m,M,s.ss,N,s.ss,K,M*hh<CR><LF>

Type Description

h.hh

Heading in degrees.

Letter 'T' denoting True heading in degrees.

m.m

Magnetic heading in degrees.

Letter 'M' denoting Magnetic heading in degrees.

s.ss

Speed in knots.

Letter 'N' denoting speed in knots.

s.ss

Speed, km/h.

Letter 'K' denoting speed in km/h.

M Mode indicator.

A=autonomous; N=data not valid

1.9 ZDA – Time and Date

Current UTC time and date.

Example:

$GPZDA,071850.000,31,08,2011,,*55

Format:

$GPZDA,hhmmss.ddd,dd,mm,yyyy,xx,yy*hh

Type Description

hhmmss.ddd

UTC time in hours, minutes, seconds and fractions of a second.

UTC day of month

UTC month

yyyy

UTC year

Local zone hours. Not implemented

Local zone minutes. Not implemented

NMEA Manual based on MediaTek chipset - Manual

FTX-HW-13002-A Preliminary

Page 9 of 39

2NMEA commands

NMEA commands are used to change or query settings of the module.

Command Length:

The maximum length of each packet is restricted to 255 bytes.

Command Contents:

Preamble: One byte character. ‘$’

NMEA ID: This will identify for the NMEA parser that it will receive commands for MediaTek.

Four bytes character string. “PMTK”

Command Number: Three-byte character string.

An identifier, from “000” to “999”, is used to tell the decoder how to decode the command.

DataField:

The DataField has a variable length depending on the command type.

A comma symbol ‘,’ must be inserted before each data field to help the decoder process the DataField.

*: 1 byte character.

The star symbol is used to mark the end of DataField.

CHK1, CHK2: Two-byte character string.

CHK1 and CHK2 are the checksum of the data between Preamble and ‘*’.

CR, LF: Two bytes binary data.

The two bytes are used to identify the end of a command.

Sample Command:

$PMTK000*32<CR><LF>

You can use your preferred terminal emulator to enter commands. For example, you can use TeraTerm,

whichcan be downloaded from here: http://en.sourceforge.jp/projects/ttssh2/releases/

Remember to set the CR+LF for sending the command from the terminal program.

Figure 1: Tera Term terminal setup

Other possible terminal emulators to use include Putty and HyperTerminal.

NMEA Manual based on MediaTek chipset - Manual

FTX-HW-13002-A Preliminary

Page 10 of 39

Figure 2: HyperTerminal setup

2.1 PMTK000 TEST

Command purpose:

Test the communication between the receiver and host.

Command number:000

DataField: None

Example:

$PMTK000*32<CR><LF>

Reply: see next chapter.

2.2 PMTK001 ACK

Command purpose:

Acknowledge a PMTK000 command.

Command number:001

DataField:

PMTK001,Cmd,Flag

Cmd: The command / packet type to be acknowledged.

Flag: 0 = Invalid command / packet.

1= Unsupported command / packet type

2= Valid command / packet, but action failed

3= Valid command / packet, and action succeeded

Example:

$PMTK001,604,3*32<CR><LF>

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ublox Steuereinheit Handbücher

Ublox

Ublox TOBY-L1 series Kurzanleitung zur Einrichtung

Ublox

Ublox TOBY-L2 series Kurzanleitung zur Einrichtung

Ublox

Ublox VERA-P173 Bedienungsanleitung

Ublox

Ublox NINA-B31 Series Bedienungsanleitung

Ublox

Ublox NEO-M8P Kurzanleitung zur Einrichtung

Ublox

Ublox ODIN-W260 Kurzanleitung zur Einrichtung

Ublox

Ublox NINA-B222-04B Kurzanleitung zur Einrichtung

Ublox

Ublox LISA-C2 Series Kurzanleitung zur Einrichtung

Ublox

Ublox NORA-B1 Series Kurzanleitung zur Einrichtung

Ublox

Ublox EVK-JODY-W2 Bedienungsanleitung

Ublox

Ublox LEXI-R422 Kurzanleitung zur Einrichtung

Ublox

Ublox SAM-M8Q Gebrauchs- und Pflegehandbuch

Ublox

Ublox ZED-F9P Gebrauchs- und Pflegehandbuch

Ublox

Ublox ZED-F9P Gebrauchs- und Pflegehandbuch

Ublox

Ublox SARA-R42 Bedienungsanleitung

Ublox

Ublox NEO-M8N Kurzanleitung zur Einrichtung

Ublox

Ublox ZOE-M8B Series Kurzanleitung zur Einrichtung

Ublox

Ublox NEO-M8P-2 Kurzanleitung zur Einrichtung

Ublox

Ublox SARA-R4 Series Kurzanleitung zur Einrichtung

Ublox

Ublox NINA-B1 Series Bedienungsanleitung

Ublox

Ublox MPCI-L2 series Kurzanleitung zur Einrichtung

Ublox

Ublox NINA-B2 series Kurzanleitung zur Einrichtung

Ublox

Ublox C027-U20 Bedienungsanleitung

Ublox

Ublox MAX-8 Series Kurzanleitung zur Einrichtung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung