UEi IRP-2 Bedienungsanleitung

Infrared Printer

IRP-2

Infrared Printer

Page 2

The IRP-2 is a portable printer using thermal paper that links to other

UEi products using an infrared link. It incorporates an ‘easy load’ paper

facility and allows NiMh batteries to be recharged in situ.

OPERATING THE PRINTER

BUTTON LAYOUT AND FUNCTIONS

Fig 1:

Fig 2:

ON / OFF

DARKEN CONTRAST

PAPER FEED

LIGHTEN CONTRAST

DC 5V

USB CHARGING

CABLE INPUT

The IRP-2 is a portable printer using thermal paper that links to other UEi products using

an infrared link. It incorporates an ‘easy load’ paper facility and allows NiMh batteries to

be recharged in situ.

OPERATINGTHE PRINTER

BUTTON LAYOUT AND FUNCTIONS

Page 2

The IRP-2 is a portable printer using thermal paper that links to other

UEi products using an infrared link. It incorporates an ‘easy load’ paper

facility and allows NiMh batteries to be recharged in situ.

OPERATING THE PRINTER

BUTTON LAYOUT AND FUNCTIONS

Fig 1:

Fig 2:

ON / OFF

DARKEN CONTRAST

PAPER FEED

LIGHTEN CONTRAST

DC 5V

USB CHARGING

CABLE INPUT

Page 2

The IRP-2 is a portable printer using thermal paper that links to other

UEi products using an infrared link. It incorporates an ‘easy load’ paper

facility and allows NiMh batteries to be recharged in situ.

OPERATING THE PRINTER

BUTTON LAYOUT AND FUNCTIONS

Fig 1:

Fig 2:

ON / OFF

DARKEN CONTRAST

PAPER FEED

LIGHTEN CONTRAST

DC 5V

USB CHARGING

CABLE INPUT

ON / OFF

PAPER FEED

USB CHARGING

CABLE INPUT

PAPER COVER

RELEASE LEVER

DARKEN CONTRAST

LIGHTEN CONTRAST

Fig 2

Fig 1

Page 2

The IRP-2 is a portable printer using thermal paper that links to other

UEi products using an infrared link. It incorporates an ‘easy load’ paper

facility and allows NiMh batteries to be recharged in situ.

OPERATING THE PRINTER

BUTTON LAYOUT AND FUNCTIONS

Fig 1:

Fig 2:

ON / OFF

DARKEN CONTRAST

PAPER FEED

LIGHTEN CONTRAST

DC 5V

USB CHARGING

CABLE INPUT

POWER SUPPLY

Power is supplied to the printer in the form of four AA Ni-MH batteries, which can be

re-charged by connecting the supplied USB lead (WIR00067) and battery charger

(PLU00066) to the IRP-2 USB charging socket. Fig 2. Four batteries are required. Types

cannot be mixed.

Note: The battery charger (PLU00066) cannot supply the full power requirement to the

IRP-2, the batteries must contain some charge before printing will be possible.

The battery charger supplied with the product is rated for indoor use only. Its voltage input

must be in the range 100 – 240 V AC at 50 – 60 Hz with a current capability of 0.2 A. The

chargers output voltage is 5V DC at a maximum of 1 A.

WARNING: Do NOT attempt to recharge non-rechargeable batteries as this can lead

to batteries leaking and over-heating.

WARNING: Do NOT use Alkaline AA batteries.

USINGTHE IRP-2

Switch the printer on using the power ON/OFF key as shown in ﬁg 1, the status indicator

will become illuminated (RED LIGHT).

Note: The printer will automatically switch off after around 10 minutes of inactivity. To

reactivate, simply press the ON/OFF key. If the battery power falls to low, the current print

will be suspended and the status indicator (RED light) will ﬂash 4 times, connect the pow-

er supply/charger to continue printing.

POSITIONINGTHE PRINTER AND INSTRUMENT

Ensure that there are no obstructions between the instrument emitter (at the top of the

instrument) and the IRP-2 receiver (By the status indicator).

Angle=0° Distance<=4.5m

Angle=45° Undeﬁned (Horizontal)

Angle=90° Undeﬁned (Vertical)

ADDITIONAL INFORMATION

SELFTEST

Power off the IRP-2, hold down the PAPER FEED key and press POWER ON/OFF key, the

output will be all the letters including the Latin format

PRINT CONTRAST

The contrast of the IRP-2 output can be adjusted both lighter and darker by pressing the

designated keys shown in ﬁg 1.

Page 4

REPLACING THE PAPER ROLL

To replace the paper roll in the IRP-2, release the paper cover by pressing down the

release lever.

Remove the old paper roll core and insert the new roll so that it sits as follows :-

DC 5V

REPLACINGTHE PAPERROLL

To replace the paper roll in the IRP-2, release the paper cover by pressing down the

release lever.

Remove the old paper roll core and insert the new roll so that it sits as follows :-

Page 4

REPLACING THE PAPER ROLL

To replace the paper roll in the IRP-2, release the paper cover by pressing down the

release lever.

Remove the old paper roll core and insert the new roll so that it sits as follows :-

DC 5V

PAPER COVER

RELEASE LEVER

Page 5

Lay the free end of paper over the printer head, past the serrated paper cutter onto the body

of the front of the printer’s case. Now close the paper cover and gently press down until it

locks into place. Start the paper feed sequence to confirm that the paper has been correctly

loaded. Tear off the excess paper by pulling it against the paper cutter.

WARNING. Never pull the paper through the printer always use “paper feed”.

Note: if the ‘paper out’ warning light is still flashing (see below) switch the printer off and then

on again.

STATUS INDICATOR (RED LIGHT)

PAPER OUT

The IRP -2 will automatically detect when the paper has run out, the STATUS

INDICATOR will repeatedly flash.

LOW BATTERY

Low battery is indicated by the STATUS INDICATOR flashing three times.

Connect the AACA4 to the charging socket shown in Fig 2.

HEAD THERMAL LIMIT

In the event of extensive printing periods the temperature of the thermal head of the

IRP-2 may rise to an unusable level, if this occurs the STATUS INDICATOR will flash twice

and printing will be suspended until the temperature falls to an acceptable level.

DC 5V

Lay the free end of paper over the printer head, past the serrated paper cutter onto the

body of the front of the printer’s case. Now close the paper cover and gently press down

until it locks into place. Start the paper feed sequence to conﬁrm that the paper has been

correctly loaded. Tear off the excess paper by pulling it against the paper cutter.

WARNING. Never pull the paper through the printer always use “paper feed”.

Note: if the ‘paper out’ warning light is still ﬂashing (see below) switch the printer off and

then on again.

STATUS INDICATOR (RED LIGHT)

PAPER OUT

The IRP-2 will automatically detect when the paper has run out, the STATUS INDICATOR

will repeatedly ﬂash.

LOW BATTERY

Low battery is indicated by the STATUS INDICATOR ﬂashing three times. Connect the USB

lead (WIR00067) and battery charger (PLU00066) to the charging socket shown in Fig 2.

HEADTHERMAL LIMIT

In the event of extensive printing periods the temperature of the thermal head of the IRP-2

may rise to an unusable level, if this occurs the STATUS INDICATOR will ﬂash twice and

printing will be suspended until the temperature falls to an acceptable level.

CONTROLLING THE PRINT HEAD

If you turn the printer off whilst printing, the print head may stop in the middle of the line.

To return the print head to the left side of the paper, turn the printer on, then off.

MISSING OR MISFORMED CHARACTERS

The character will show on the print out if the printer has detected incorrect data due to

interference with, or interruption to, the stream of incoming information.

Common causes for this error include incorrect positioning of printer with reference to the

instrument (this can either be due to the distance or the angle of operation), obstruction of

the infrared signal or even interference from another infrared emitting source.

ENVIRONMENTAL LIMITS

The IRP-2 is designed for indoor use only.

Operating temperature: 32°F to 104°F (0°C to 40°C)

Storage temperature: -4°F to 140°F (-20°C to 60°C)

Humidity: 5% to 95% relative at 104°F(40°C)non condensing

BATTERIES

This product is designed for only rechargeable NiMh AA batteries. Four batteries

are needed. Types cannot be mixed.

WARNING: Do NOT attempt to recharge non-rechargeable batteries as this can

lead to batteries leaking and over-heating.

WARNING: Do NOT use Alkaline AA batteries

The battery charger supplied with the product is rated for indoor use only. Its voltage

input must be in the range 100 – 240 V ac at 50 – 60 Hz with a current capability of 0.3 A.

The chargers output voltage is 9 V dc at a maximum of 0.66 A. The charger has no user

serviceable components.

Only a correctly speciﬁed and rated charger must be used with the product. part number

is USB lead (WIR00067) and battery charger (PLU00066).

CLEANING

The outer case and protective boot (if applicable) can be cleaned using a damp cloth and

non abrasive detergent. After cleaning leave the product in a warm dry place until the

surfaces are completely dry. Under no circumstance use solvent or hydrocarbon based

products as they can cause serious damage to plastic and rubber.

SERVICING

This product contains no user serviceable parts.

SAFETY

This product has been tested for compliance with EN 61010-1:2010 (Safety requirements

for electrical equipment for measurement, control and laboratory use.) and is certiﬁed to

be compliant.

END OF LIFE PRODUCT DISPOSAL

At the end of the product’s life it should be re-cycled in accordance with current

legislation and local guidelines.

BATTERY DISPOSAL

Always dispose of depleted batteries using approved disposal methods that protect the

environment.

ELECTROMAGNETIC COMPATIBILITY

European Council Directive 89/336/EEC requires electronic equipment not to generate

electromagnetic disturbances exceeding deﬁned levels and have adequate immunity

levels for normal operation. Speciﬁc standards applicable to this printer are stated below.

As there are electrical products in use pre-dating this Directive, they may emit excess

electromagnetic radiation levels and, occasionally, it may be appropriate to check the

printer before use by:

Use the normal start up sequence in the location where the printer will be used.

Switch on all localized electrical equipment capable of causing interference.

Check all readings are as expected. A level of disturbance is acceptable

If not acceptable, adjust the printer’s position to minimize interference or switch

off, if possible, the offending equipment during your test.

At the time of writing this manual (May 2016) UEi Test Instruments is not aware of any ﬁeld

based situation where such interference has occurred and this advice is only given to

satisfy the requirements of the Directive.

Please Note:

Batteries used in this instrument should be disposed of in accordance with current

legislation and local guidelines.

At the end of the product’s life it should be re-cycled in accordance with current

legislation and local guidelines.

www.ueitest.com

Email: [email protected]

1-800-547-5740

This product has been tested for compliance with the

following generic standards:

EN 61000-6-3 : 2011

EN 61000-6-1 : 2007

and is certiﬁed to be compliant

Speciﬁcation EC/EMC/KI/KANE IRP-2/1

details the speciﬁc test conﬁguration,

performance and conditions of use.

Inhaltsverzeichnis

Andere UEi Drucker Handbücher

UEi

UEi KMIRP2 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung