UEi C161KIT Bedienungsanleitung

C161 QuiCk Start Guide

C161

Status

Aux

O2/Eff CO/CO2 Temp

Exch Test

BACKED BY

1-800-547-5740 • Fax: (503) 643-6322

www.ueitest.com • Email: [email protected]

C161 OVERVIEW

C161

Status

Aux

O2/Eff CO/CO2 Temp

Exch Test

T2 T1

Protective boot with

built-in magnets

Log & Print

Temperature screen

LED Water Trap Full

Indication

Water Trap Window

K-type temperature inputs

Combustion hose input

Water trap drain plug

Power button

Display lines

1 through 6

Status bar line

Navigation

USB charging port

O2/Eff screens

CO/CO2 screens

Pump

Auxiliary screen

Status screen

Menu screen

Press ”Power” Button for 2 seconds. The analyzer will

perform a 60 second purge. This should be done in fresh

air.

Rotate Selector Dial to MENU to set up or customize

your settings.

Selected parameter are centered, highlighted with arrow

icons on either side.

Use and buttons to scroll menu options,

Press to select and edit a parameter.

Press and buttons to change contents of a ﬁeld.

Press button to scroll ﬁelds.

Press to enter content and move to next ﬁeld.

C161

Status

Aux

O2/Eff CO/CO2 Temp

Exch Test

MENU SCREEN - C161 START UP

STATUS SCREEN

Rotate Selector Dial to STATUS to view parameters.

Selected Fuel

Ti = Ambient Temperature

ATM = Atmospheric Pressure (measured in mbar)

CAL = Days remaining until calibration

Press and buttons to scroll Status Bar

options.

Time, Pump Status, Battery Status

Fuel Type

Date

Change Fuel Type in STATUS SCREEN

Press and buttons to the currently selected fuel.

Press and Hold button until arrows indicate fuel

edit mode is activated.

The and to scroll fuel types.

Press to select desired fuel.

C161

Status

Aux

O2/Eff CO/CO2 Temp

Exch Test

Status

Aux

O2/Eff CO/CO2 Temp

Exch Test

C161

Status

Aux

O2/Eff CO/CO2 Temp

Exch Test

C161

COMBUSTION ANALYSIS

T2 T1

Insert ﬂue probe into stack.

Adjust cone so the probe tip is

approximately at the center of

the stack.

Insert ﬂue probe into combustion

input. Insert K-type temperature

probe into input T1.

Rotate function rotary dial

to O2/Eff for Test Screen 1

parameters.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

O2/Eff displays CO2, O2, Gross

Efﬁciency, Flue temperature,

Inlet temperature.

Rotate the function rotary dial

to CO/CO2 for Test Screen 2

parameters.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

CO/CO2 displays CO (ppm),

Losses calculated, Excess air %.

Make any adjustments needed

for proper Combustion and wait

for analyzer to display change in

readings. (Repeat as necessary).

BEFORE TESTING

Remove the rubber boot and red

drain plug. Allow the water to

drain out. Re-insert the rubber

plug and replace boot cover.

Remove protective rubber boot.

Remove water trap from analyzer.

Remove particle ﬁlter from

spigot and replace with new

one. Reattach trap and boot.

CHECKLIST

oClean particle ﬁlter

oWater trap and probe line are

free of water

oAll hose and thermocouple

connections are properly

secured

oWater trap is ﬁtted correctly

oPower on and zero

oFlue gas probe is sampling

ambient FRESH air

NOTE: If there is no hole, check with service and installation instructions of appliance for best testing

method or check with your local authority on best practice

TEMPERATURE TEST

The AUX screen allows you to assign any of the following parameters on any display line.

O2, CO, Display Fuel Type, CAL, XAIR, LOSS, Efgc, ATM, Ti, ∆T, T2, T1, CO2, COa, or COn

CHANGE FUEL TYPE

Status

Aux

O2/Eff CO/CO2 Temp

Exch Test

C161

Rotate the dial to either AUX,

O2/Eff, CO/CO2 or TEMP

setting.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

Press button until the Fuel

Type displays on the Status Bar.

Press and Hold until two

arrow icons display.

Press and buttons to

scroll fuel selections.

Press to select fuel.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

AUXILIARY SCREEN

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

Status

Aux

O2/Eff CO/CO2 Temp

Exch Test

C161

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

AUX displays 5 lines of editable

parameters. To edit line values

Press button until Edit?

displays on the Status Bar.

Press and Hold until the

Status Bar reads LINE 1.

When performing a combustion

Test, Rotate function rotary dial

to AUX to view the Auxiliary

Test Screen’s custom param-

eters.

Press and buttons to

scroll parameter selections.

Press to select a parameter

and advance to the next Line.

Continue until cursor is back to

Status Bar to exit.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

Status

Aux

O2/Eff CO/CO2 Temp

Exch Test

C161

Rotate function rotary dial to

TEMP for Temperature Test

Screen.

TEMP displays T1, T2 and

Differential Temperature.

T2 T1

Insert K-type temperature

probes into input T1 and T2.

VIEW SAVED LOGS

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

Rotate the dial to MENU.

Press button until the LOGS

is selected between two arrow

icons. Press to select.

Screen displays all saved LOGS.

With VIEW selected in the Status

Bar, Press to select.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

Press and buttons to

scroll Test Report categories.

Press to select a category.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

Line 1 displays the LOG number

on screen.

To view another LOG, Press

and buttons to NEXT.

Press to advance to next log.

Repeat until you reach desired LOG.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

To print the LOG, Press

and buttons until PRINT

is selected between two arrow

icons. Press to select to start

printing.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

To EXIT, Press and

buttons until EXIT is selected

between two arrow icons. Press

to EXIT screen.

Repeat until return to MENU screen.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

PRINTING & LOGGING

To Print: Align printer (sold

separately) above Analyzer.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

During testing, Press to start

printing.

Press again to abort.

To Log: During testing, Press and

Hold to log a report.

To view these Logs, see View

Saved Logs section.

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

STATUS

FLUE 1

AUX

FLUE 2

TEMP

C161

WARRANTY

The C161 combustion analyzer is warranted for one year including sensors. If within the warranty period

your instrument should become inoperative from such defects, the unit will be repaired or replaced at

UEi’s option. This warranty covers normal use and does not cover damage which occurs in shipment or

failure which results from alteration, tampering, accident, misuse, abuse, neglect or improper mainte-

nance (calibration). Batteries and consequential damage resulting from failed batteries are not covered

by warranty. Any implied warranties, including but not limited to implied warranties of merchantability

and ﬁtness for a particular purpose, are limited to the express warranty. UEi shall not be liable for loss

of use of the instrument or other incidental or consequential damages, expenses, or economic loss, or

for any claim or claims for such damage, expenses or economic loss. A purchase receipt or other proof

of original purchase date will be required before warranty repairs will be rendered. Instruments out of

warranty will be repaired (when repairable) for a service charge. Warranty only covers hardware and

does not extend to software applications. Contact UEi for speciﬁc warranty and service information.

UEi Test Instruments • 1-800-547-5740 • [email protected]

This warranty gives you speciﬁc legal rights. You may also have other rights which vary from state to state.

Download the full

Owners Manual at

UEiTEST.COM or

SCAN THIS CODE

POST TESTING

BATTERIES

The analyzer is ﬁtted with 3

(AA) size rechargeable batter-

ies. Observe correct polarity

when replacing.

Always check operation

immediately after battery

replacement.

Do not leave batteries in unit for

extended periods of non-use.

WARNING

Do not recharge with Alka-

line batteries ﬁtted. Alkaline

batteries are not rechargeable.

Attempting to recharge alkaline

batteries may result in product

damage and create a ﬁre risk.

Time and Date will need to be

reset after changing batteries.

Always dispose batteries using

approved disposal methods that

protect the environment.

Remove the probe from the ﬂue

and allow analyzer to purge with

fresh air until readings return to

zero. O2 to 20.9%, CO to Zero

CAUTION: probe tip will be HOT.

POWERING OFF

When you power off the C161, there is a 10 second purge.

CAUTION

Make sure you do not exceed the analyzer’s operating speciﬁcations.

• Do not exceed the ﬂue probes maximum temperature (1112˚F)

• Do not exceed the analyzer’s internal temperature range 112°F (50°C)

• Do not put the analyzer on a hot surface

• Do not exceed the water trap’s level

• Do not let the particle ﬁlter become dirty and blocked

ANNUAL RECERTIFICATION SERVICES

WWW.UEITEST.COM USA 1.800.547.5740

CANADA 1.877.475.0648

UEi will:

10 Year Warranty: All UEi combustion analyzers have a standard 1-year

warranty. Each recertiﬁcation extends the warranty for 1 more year for up

to 10 years from the date of purchase.

Contractors who book recertiﬁcation of a C160 series analyzer

at www.ueitest.com/service within 12 months from either

the date of purchase or the date of the last recertiﬁcation

will receive reduced service pricing1that lowers the cost of

ownership and 2 additional beneﬁts:

Same Day Service: All qualifying analyzers received for recertiﬁcation

through UEi Service+ are returned on the same business day.*

Free Shipping: UEi Service+ offers free shipping both to and from our

service center. When customers book their recertiﬁcation, they receive a

prepaid UPS Ground shipping label.

BACKED BY

Complete care for your C160 series combustion analyzer.

When you:

Request Recertiﬁcation or Service Online

Within 1 Year of Purchase or Service

Registering you analyzer online is quick and easy. Just log in or setup an account, it only takes

a couple of minutes. Once logged in you can register you analyzer by providing some product

information and uploading a proof-of-purchase.

When it’s time to request recertifcation, just log into your account, select the analyzer, select

the service and place your order.

*Analyzers that include the additional NO (Nitric Oxide) sensor requires 48-hour turnaround.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung