ULTRA TEC G3000 Bedienungsanleitung
www.ultratecfx.com
VER. 01.11.12
G3000
Service Manual
www.ultratecfx.com
2
• Make sure the main power cord is disconnected from power
before attempting to remove the outer cover
• Make sure unit has cooled sufciently to perform the operation
1. Make sure the machine is unplugged.
2. Using a #2 Phillips Screw Driver remove the 12 screws on the lid. Carefully lift the
case off and carefully detach the grounding wire screwed to the lid.
3. Disconnect the copper tubes from the pumps by loosening the 7/16” brass nut on
the pump. This line may be under high pressure if the tube was plugged. Slowly
loosen the pump that connects to the copper 1/4 tube inlet tting to release any
pressure.
Heat Exchanger Replacement
4. Remove the two slot screws (or ¼” hex)
from the front edge of the block cover.
Slide the cover backward to release the
two back tangs from the lower cover. Lift
the cover off.
5. Remove the insulation on top.
www.ultratecfx.com 3
6. Using a ½” socket, loosen the ve nuts. Remove all 5 nuts and washers (these
will not be reused). Be careful not to damage any exposed wiring. Remove the
upper steel plate by gently lifting the plate up out of the way.
7. Remove the ¼” aluminum plate
cautiously to avoid damage to
the thermocouple. Examine the
thermocouple wires for moisture as
this may cause failures.
8. Remove the aluminum wear plate
that is positioned above the coil (this
will not be reused).
9. Remove the used copper tube from
the block (this part will not be
reused).
www.ultratecfx.com
4
10. Remove the second thin wear plate
(this part will not be reused).
11. Lift the thick aluminum plate up
cautiously to avoid damage to the
heaters.
12. Remove the third thin wear plate
(this part will not be reused).
13. Remove the second coil from
the block (this part will not be
reused).
www.ultratecfx.com 5
14. Remove the forth thin wear plate
(this part will not be reused).
15. When replacing the parts, ensure all mating surfaces are clean to promote good
thermal conduction.
16. Place a new narrow aluminum wear
plate on the block. Note: All plates
can only be installed one way due
to the offset bolt pattern. There are
two sizes of wear plates (narrow and
wide)
17. Place the new copper tube on the
wear plate. Adjust the runs of the
tube so they do not touch the bolts.
The bends in the coil must be facing
DOWNWARDS.
www.ultratecfx.com
6
18. Place a new wide aluminum wear
plate on the coil.
19. Place the thick aluminum plate onto
the wear plate.
20. Place a new wide aluminum wear
plate on the thick aluminum plate.
21. Place the second copper tube on
the wear plate. Adjust the runs of the
tube so they do not touch the bolts.
The bends in the coil must be facing
UPWARDS.
www.ultratecfx.com 7
22. Place a new narrow aluminum wear
plate on the coil.
23. Place the 1/4” aluminum plate on the
wear plate.
24. Add the upper steel plate while
checking that the wires are not
pinched or shorted. Thread the ve
new nuts and washers on nger
tight. Check the alignment of the
layers. Tighten the center nut down
snug with a ½” socket. Repeat
with the other four nuts. Move to
the center nut and pull tighter by a
quarter turn. This will give 5-7lbs of
torque. Repeat this on the remaining
four nuts.
25. Attach the tubes by screwing in the 7/16” brass nut at the pumps.
Tighten securely.
26. Reinstall the top insulation. Power up the G3000 and allow it to heat up fully.
Run fog through the fog machine until it reaches its lowest output. Turn off the
fog machine and disconnect from the power source. Retighten bolts if necessary.
27. Reconnect the grounding wire to the case and slide the lid into place and fasten
the machine screws. Plug the machine in and allow it to heat up completely. Now
you’re ready to fog.
Note: For a detailed visual and indentifcation of parts, visit the service section of the G3000
on www.ultratecfx.com and view the “G3000 Heater Block Parts Identication Sheet”.
Andere Handbücher für G3000
6
Inhaltsverzeichnis
Andere ULTRA TEC Nebelmaschine Handbücher
ULTRA TEC
ULTRA TEC IceJet III Bedienungsanleitung
ULTRA TEC
ULTRA TEC 9D Bedienungsanleitung
ULTRA TEC
ULTRA TEC Stage Fogger DMX Bedienungsanleitung
ULTRA TEC
ULTRA TEC Silent Storm Bedienungsanleitung
ULTRA TEC
ULTRA TEC LSG PFI-9D Bedienungsanleitung
ULTRA TEC
ULTRA TEC Ultra Handy Fogger Bedienungsanleitung
ULTRA TEC
ULTRA TEC CLF2460 Bedienungsanleitung
ULTRA TEC
ULTRA TEC G3000 Bedienungsanleitung
ULTRA TEC
ULTRA TEC LSX Bedienungsanleitung
ULTRA TEC
ULTRA TEC Radiance Hazer Bedienungsanleitung
Beliebte Nebelmaschine Handbücher anderer Marken
Antari
Antari ICE Bedienungsanleitung
Boost
Boost BOOST-FOG400LED-BK Bedienungsanleitung
Home Accents Holiday
Home Accents Holiday FM1000-ASH Bedienungsanleitung
EuroLite
EuroLite ZEITGEIST FOG-1200 Bedienungsanleitung
Dyna-Fog
Dyna-Fog CYCLONE ULTRA 2734 Bedienungsanleitung
PROEL
PROEL DRAGO HEAVY PLFD150HY Bedienungsanleitung
