G36D Zero Clearance Direct Vent Gas Fireplace
Check all clearances to combustibles. Refer
to the following sections:
a) Locating Your Gas Stove
Assemble Top Standoffs and Top Facing
Support and Side Nailing Strips, Refer to the
"Unit Aseembly Prior to Installation" section.
(NOTE: must be done before installing unit
Install vent. Refer to the "Venting"
Install standard and optional features.
Refer to the following sections where
c. Option 1: Remote Control
e. Option 3: Wall Thermostat
f. Installating the Optional Fan
Before leaving this unit with the customer,
the installer must ensure that the appliance is
operation fully explained
Fireplace must be installed in accordance
with these instructions. Carefully read all the
instructions in this manual fi rst. Consult the
"authority having jurisdiction" to determine the
need for a permit prior to starting the installation.
It is the responsibility of the installer to ensure
this fi replace is installed in compliance with
manufacturer's instructions and all applicable
Safe installation and operation of this appliance
requires common sense, however, we are
required by the Canadian Safety Standards
The appliance installation must conform
with local codes or, in the absence of local
codes, with the current Canadian or National
Gas Codes, CAN1-B149 or ANSI Z223.1
The appliance when installed, must be
electrically grounded in accordance with
local codes, or in the absence of local codes
with the current National Electrical Code,
ANSI/NFPA 70 or CSA C22.1 Canadian
See general construction and assembly
instructions. The appliance and vent should
This appliance must be connected to the
specifi ed vent and termination cap to the
outside of the building envelope. Never vent
to another room or inside a building. Make
sure that the vent is fi tted as per Venting
Inspect the venting system annually for
blockage and any signs of deterioration.
Venting terminals shall not be recessed into
Any safety glass removed for servicing
must be replaced prior to operating the
To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
Wear gloves and safety glasses for protection
while doing required maintenance.
Be aware of electrical wiring locations in
walls and ceilings when cutting holes for
Under no circumstances should this
appliance be modifi ed. Parts that have to
be removed for servicing should be replaced
prior to operating this appliance.
Installation and any repairs to this appliance
should be done by a qualifi ed service person.
A professional service person should be
called to inspect this appliance annually.
Make it a practice to have all of your gas
appliances checked annually.
Do not slam shut or strike the glass door.
Under no circumstances should any solid
fuels (wood, paper, cardboard, coal, etc.)
be used in this appliance.
The appliance area must be kept clear and
free of combustible materials, (gases and
other fl ammable vapours and liquids).
INSTALLATION AND REPAIR SHOULD
BE DONE BY A QUALIFIED SERVICE
PERSON. THE APPLIANCE SHOULD
AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVE
THAT CONTROL COMPARTMENTS,
BURNERS AND CIRCULATING AIR
PASSAGEWAYS OF THE APPLIANCE
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE
CHILDREN AND ADULTS SHOULD
BE ALERTED TO THE HAZARDS OF
HIGH SURFACE TEMPERATURES,
ESPECIALLY THE FIREPLACE GLASS,
AND SHOULD STAY AWAY TO AVOID
BURNS OR CLOTHING IGNITION.
CAREFULLY SUPERVISED WHEN
THEY ARE IN THE SAME ROOM AS
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
