Viper Cut 30 Manual | 7
Electrode
Air Diffuser
Tip
Plasma Stream
Electrode Insert
Shield Cup
Plasma cutters work by passing an electric arc through a gas that is passing through a constricted opening. The gas can be air, nitrogen, argon, oxygen.
etc. The electric arc elevates the temperature of the gas to the point that it enters a 4th state of matter. We all are familiar with the rst three: i.e., Solid,
liquid, and gas. Scientists call this additional state plasma. As the metal being cut is part of the circuit, the electrical conductivity of the plasma causes the
arc to transfer to the work. The restricted opening (Tip) the gas passes through causes it to squeeze by at a high speed, like air passing through a venturi in
a carburettor. This high speed gas cuts through the molten metal. Plasma cutting was invented as the result of trying to develop a better welding process.
Many improvements then led to making this technology what it is today. Plasma cutters provide the best combination of accuracy, speed, and affordability
for producing a variety of at metal shapes. They can cut much ner, and faster than oxy-acetylene torches.
HOW A PLASMA CUTTER WORKS:
Basic plasma cutters use electricity to superheat air into plasma (the 4th state of matter), which is then blown through the metal to be cut. Plasma cutters
require a compressed air supply and AC power to operate.
Operation:
1. When the trigger is squeezed, DC current ows through the torch lead into the tip.
2. Next, compressed air ows through the torch head, through the air diffuser that spirals the air ow around the electrode and through the hole of the
cutting tip.
3. A xed gap is established between the electrode and the tip. (The power supply increases voltage in order to maintain a constant current through the
joint.) Electrons arc across the gap, ionizing and super heating the air creating a plasma stream.
4. Finally, the regulated DC current is switched so that it no longer ows to the tip but instead ows from the electrode to the work piece. Current and
airow continue until cutting is stopped.
NOTES:
The nozzle and electrode require periodic replacement. The electrode has an insert of tough high conductive material such as hafnium and cerium. This
insert erodes with use, also the tip orice will erode with use. Quality of the air used is paramount to longer life of electrodes and tips, in short clean dry air
gives longer parts life, the cleaner and dryer the better. We recommend use of a Plasma Air Filter.
What kinds of materials can the plasma cut?
Virtually any metal can be plasma cut including steel, stainless steel, aluminium, brass, copper, etc. Any thickness from 30 gauge through 30mm can be
cut, depending on the power of the plasma cutter used.
How Does Plasma Cutting Compare to Oxy-fuel (gas) cutting?
Plasma cutting can be performed on any type of conductive metal - mild steel, aluminium and stainless are some examples. With mild steel, operators will
experience faster, thicker cuts than with alloys.
Oxy-fuel cuts by burning, or oxidizing the metal it is severanceing. It is therefore limited to steel and other ferrous metals which support the oxidizing
process. Metals like aluminium and stainless steel form an oxide that inhibits further oxidization, making conventional oxy-fuel cutting impossible. Plasma
cutting however does not rely on oxidation to work and thus it can cut aluminium, stainless and any other conductive material. While different gasses can
be used for plasma cutting, most people today use compressed air for the plasma gas. In most shops, compressed air is readily available, and thus plasma
does not require fuel gas and compressed oxygen for operation.
Plasma cutting is typically easier for the novice to master, and on thinner materials, plasma cutting is much faster than oxy-fuel cutting. However, for heavy
sections of steel (25mm and greater), oxy-fuel is still preferred since oxy-fuel is typically faster and, for heavier plate applications high powered plasma
machines are required for plasma cutting applications.
What are the limitations to Plasma Cutting? Where is Oxyfuel preferred?
The plasma cutting machines are typically more expensive than oxy/acetylene. Also, oxy/acetylene does not require access to electrical power or
compressed air which may make it a more convenient method for some users. Oxyfuel can generally cut thicker sections (>25mm) of steel more quickly
than plasma.
AIR PLASMA CUTTING TECHNOLOGY
