Uni-Mig RWX 6000 Bedienungsanleitung

UMCWH

2 YEAR

WARRANTY

0356 RWX6000 Helmet Manual MAY19.indd 1 8/05/2019 3:53:51 PM

SAFETY 3

FEATURES 4

HELMET BREAKDOWN 5

FILTER DISPLAY ICONS 6

OPERATING INSTRUCTIONS 7

TROUBLESHOOTING 10

NOTES 11

RECOMMENDED SHADE SETTINGS 12

CONTENTS

2 | RWX6000 Welding Helmet Manual

0356 RWX6000 Helmet Manual MAY19.indd 2 8/05/2019 3:53:51 PM

SAFETY

Please read and understand all instructions before using.

• Be sure that the dark shade of the lens in the welding helmet is on the correct shade number for

your application.

• The helmet and lenses are not suitable for “overhead” welding application, laser welding, or laser

cutting applications.

• Welding helmets are designed to protect the eyes and face from sparks, spatter, and harmful

radiation under normal welding conditions.

• This helmet will not protect against explosive devices or corrosive liquids. Machine guards or eye

splash protection must be used when these hazards are present.

• Impact resistant, primary eye protection, spectacles or goggles that meet current ANSI

speciﬁcations, must be worn at all times when using this welding helmet.

• Avoid work positions that could expose unprotected areas of the body to sparks, spatter, direct

and/or reﬂected radiation. Use appropriate protection if exposure cannot be avoided.

• Before each use, check that the protection plates are clean and that no dirt is covering the sensors

on the front of the lens.

• Inspect all operating parts before each use for signs of wear or damage. Any scratched, cracked,

or pitted parts should be replaced immediately.

• Do not make any modiﬁcations to either the welding lens or helmet, other than those speciﬁed

in this manual. Do not use any replacement parts other than those speciﬁed in this manual.

Unauthorised modiﬁcations and replacement parts will void the warranty and expose the user to

the risk of personal injury.

• If this lens does not darken when striking arc, stop welding immediately and check the helmet

is in Weld Mode and not Grind Mode. If the issue persists, contact your local UNIMIG Service

Department.

• Do not immerse this lens in water.

• Do not use any solvents on any lens or helmet components.

• The recommended operating temperature range for this welding lens is -10°C to 65°C (14°F-149°F ).

Do not use this device beyond these temperature limits.

• Failure to follow these warnings and/or failure to follow all of the operating instructions could result

in severe personal injury.

RWX6000 Welding Helmet Manual | 3

0356 RWX6000 Helmet Manual MAY19.indd 3 8/05/2019 3:53:51 PM

FEATURES

The RWX6000 Welding Helmet is equipped with an automatic darkening ﬁlter. The ﬁlter is transparent

before welding so that the operator may observe the work surface clearly. When striking the arc, the

ﬁlter darkens automatically immediately. When the arc goes out, the ﬁlter will become transparent

again. The switching time from light to dark is 0.08 ms. The switching time from dark to light may be

set up within 0.1-0.9 second.

The helmet is equipped with a continuous darkness-adjusting unit so that the operator may select an

arbitrary dark shade number ranging from 5-9 or 9-13. The helmet also features 3 memory states to

save desired settings.

The RWX6000 Welding Helmet gives the operator permanent complete protection against UV/IR,

even in the transparent state. The UV/IR protection level is up to DIN15. The power is provided by

solar cells and a replaceable battery.

The helmet is equipped with four photosensors to sense arc light. In addition, the helmet contains an

outer protection shell made of high polymer materials. The plate is wear-resistant, thermostable, and

has no dregs-sticking, giving a very long service life.

The RWX6000 Welding Helmet is a TRUE COLOUR VIEW welding helmet. With advanced TRUE

COLOUR VIEW technology, the users can weld with improved clarity due to new Blue Optical Coating

technology, grind with precision while in grind mode and ﬁnally see the job performance in the light

state in the full spectrum of colours. There is now no need to remove the helmet to see clearly!

TECHNICAL DATA

SKU UMRWXWH

Filter Dimensions 114 x 133 x 9.5 mm

View Size 100 x 83.4 mm

Classiﬁcation 1/1/1/1

Light State 4

Dark State 5-9 / 9-13

UV/IR Protection DIN15

Time from Light to Dark 0.08ms

Time from Dark to Light 0.1-0.9s

TECHNICAL DATA

Sensitivity Delay Adjustable (1-5 for low-high)

Power Supply Solar Cells & CR2450

Replaceable Battery

Warranty 2 Years

Operating Temperature -10˚C to 65˚C

Storage Temperature -20˚C to 85˚C

Shade Control Ye s

Grind Mode Ye s

Standards CE EN379, ANSI Z87.1,

CSA Z94.3,

4 | RWX6000 Welding Helmet Manual

0356 RWX6000 Helmet Manual MAY19.indd 4 8/05/2019 3:53:51 PM

# Description

1 Helmet shell

2 Positioning point for the segmental plate

3 Outer protection lens

4 ADF cradle

5 Magnifying lens holder

6 Retainer lock

7 Auto ﬁlter

8 Battery holder

9 Battery

10 Inner protection lens

11 Display screen

12 Memory buttons(3)

13 Weld/Grind button

# Description

14 Delay button

15 Sensitivity button

16 Shade button

17 Headgear slider (with 3 slots)

18 Headgear screw (Short, on left)

19 Headband tightness adjusting knob

20 Headgear connector

21 Headgear screw (Long, on right)

22 Block washer (on right)

23 Headband adjusting buttons

24 Segmental positioning plate (on right)

25 Sweatband

26 Block nut (2pcs, left & right)

HELMET BREAKDOWN

RWX6000 Welding Helmet Manual | 5

0356 RWX6000 Helmet Manual MAY19.indd 5 8/05/2019 3:53:52 PM

1. Battery Status 2. Welding Indication 3. Grinding Indication 4. Shade Range 5-9 5. Shade Range 9-13

6. Sensitivity indication:

1 (low) to 5(high)

7. Delay indication:

1 (short 0.1s) to 5 (long 0.9s) 8. Shade reading 9. Memory selection

FILTER DISPLAY ICONS

Note: Buttons on the left of the screen need to be pressed twice to start any settings. Otherwise they will not operate.

6 | RWX6000 Welding Helmet Manual

0356 RWX6000 Helmet Manual MAY19.indd 6 8/05/2019 3:53:53 PM

OPERATING INSTRUCTIONS

VARIABLE SHADE CONTROL

• If the Shade is in the range of 5-9, press WELD/GRIND button (13) repeatedly until both Icon 2 and

Icon 4 appears on the screen. Then press SHADE button (16) repeatedly until the desired Shade

shown in Icon 8.

• If the Shade is in the range of 9-13, press WELD/GRIND button (13) repeatedly until both Icon 2 and

Icon 5 appears on the screen. Then press SHADE button (16) repeatedly until the desired Shade

shown in Icon 8.

Note:

• Choose an optimum Shade number for the required welding process or application.

• If this lens does not darken when striking arc, stop welding immediately and check the helmet

is in Weld Mode and not Grind Mode. If the issue persists, contact your local UNIMIG Service

Department.

SENSITIVITY CONTROL

The responsiveness to dierent light levels in various welding processes can be adjusted in the

range 1-5(from low to high).

Press the SENSITIVITY button (15) twice to start the setting, Icon 6 will ﬂash on the screen (from 1 to

5). Repeatedly press the SENSITIVITY button until the desired level shown in Icon 6.

• Turn to 1 (low): The photosensitivity changes to be lower.

– Suitable for high amperage welding and welding in bright light conditions (lamp light or sunlight).

• Turn to 5 (high): The photosensitivity changes to be higher.

– Suitable for low amperage welding and using in poor light conditions.

– Suitable for use with steady arc process such as TIG welding.

– Under normal use, a higher sensitivity setting is recommended.

DELAY CONTROL

The length of time delay for the ADF to return to the light state after welding can be adjusted in the

range 1-5 (for 0.1-0.9s). The time delay is for protection of the welder’s eyes from strong residual rays

after welding.

Press the DELAY button (14) twice to start the setting, Icon 7 will ﬂash on the screen (from 1 to 5).

Repeatedly press the DELAY button until the desired length of time delay shown in Icon 7.

RWX6000 Welding Helmet Manual | 7

0356 RWX6000 Helmet Manual MAY19.indd 7 8/05/2019 3:53:53 PM

• Turn to 1 (0.1s): The time the ADF takes to lighten after welding becomes shorter. The shortest time

is about 0.1s depending on the welding point temperature and shade setting. This setting is ideal

for track welding or production welding with short welds.

• Turn to 5 (0.9s): The time the ADF takes to lighten after welding becomes longer. The longest time

is about 0.9s depending on the welding point temperature and shade setting. This setting is ideal

for welding at high amperage where there is an afterglow from the weld.

GRIND SELECTION

Press WELD/GRIND button (13) repeatedly until Icon 3 appears on the screen and the red light on the

button ﬂashes. Additionally, Icon 8 will show shade 4.

Note: Do not weld in the Grind mode, the ADF will not darken.

MEMORY SETTING

The three most frequently used settings can be stored and reactivated easily by using the 3 MEMORY

buttons (12) on the right side of the screen.

Upon use of this helmet, the last ADF settings will be stored automatically (stored about 5 minutes

after). The next time when you start to weld, the last settings will be automatically re-activated.

• If you want to store a complete welding setting, press and hold one of the memory buttons and

release when the Icon 9 stops ﬂashing.

• To activate the stored memory, press the memory button.

Note: Only in welding mode you can activate the memory. Change to welding mode if you are

currently using the grinding function.

HEADGEAR ADJUSTMENTS

The harness can be adjusted for better comfort during operation. The Headband Adjustment Button

(23) adjusts the size of the headband. The Segmental Positioning Plate (24) adjusts the viewing

angle. The Headband Tightness Knob (19) adjusts the tightness of the headband.

BATTERY INDICATOR

Icon 1 indicates battery status. Replace the battery when it is low; otherwise, the ADF switching time

will become slower, and shade accuracy will be compromised.

POWER SUPPLY AND REPLACING THE BATTERY

The power of the auto-darkening helmet is provided by solar cells and a CR2450 lithium battery. To

change the battery, open the Battery holder (8) at the side of the ADF and replace the battery (9).

OPERATING INSTRUCTIONS

8 | RWX6000 Welding Helmet Manual

0356 RWX6000 Helmet Manual MAY19.indd 8 8/05/2019 3:53:53 PM

ADDITIONAL INSTRUCTIONS

• Be sure that the helmet is used in the correct condition and according to the SAFETY content.

• There is a liquid crystal-valve in the ﬁlter, although it has inner and outer protection plate, it is

important to avoid heavy knocks to the helmet.

• The outer protective shell of the helmet should be periodically inspected and cleaned. In the case

of a break, crack, pitting or other damage, the helmet shell must be replaced.

• To operate more eciently and safely, please select the correct dark shade number.

• The arc light must be visible completely by the sensor. If not, the ﬁlter will be transparent or

unstable in darkness.

• Please use the automatic ﬁlter at a temperature between -10°C-65°C (14°F-149°F )

• Do not disassemble the ﬁlter. If any problems arise, please contact your local UNIMIG service

department.

REPLACEABLE PARTS

• Outer Lens - UMRBOP

• Inner Lens - UMRWXIP

• Harness - UMRWXHR

• Sweat Band - UMSB

OPERATING INSTRUCTIONS

RWX6000 Welding Helmet Manual | 9

0356 RWX6000 Helmet Manual MAY19.indd 9 8/05/2019 3:53:53 PM

TROUBLESHOOTING

PROBLEM SOLUTION

The ADF does not darken when welding

• Stop welding or cutting immediately.

• Make sure the sensors are facing the arc

and there are no obstructions.

• Check the mode is on WELD, not GRIND.

• Review sensitivity recommendations and

adjust sensitivity if possible.

• Replace the battery if necessary.

The ADF stays dark after welding or there is no arc

present

• Adjust the sensitivity to a lower level.

• If the work-site is too bright, it is recommended

to reduce the surrounding light level.

The ADF switches during the welding

• Increase the sensitivity if possible.

• Make sure the sensors are facing the arc

and there are no obstructions.

• Increase Delay 0.1 − 0.3 seconds may also

reduce switching.

Inconsistent shade number on the corner of ADF

• It is a natural feature and will not be

dangerous for the eyes.

• To get maximum comfort, try to keep a view

angle at around 90°.

WARRANTY

UNIMIG auto-darkening welding helmets are covered for warranty for up to two years from the date

of purchase. The duration of use depends on various factors such as use, cleaning storage and

maintenance. Frequent inspections are recommended.

10 | RWX6000 Welding Helmet Manual

0356 RWX6000 Helmet Manual MAY19.indd 10 8/05/2019 3:53:53 PM

Inhaltsverzeichnis

Andere Uni-Mig Motorradzubehör Handbücher

Uni-Mig

Uni-Mig Core Series Bedienungsanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

SW-Motech

SW-Motech SBL.01.971.10000/B Bedienungsanleitung

GÜDE

GÜDE GSH 180-TC-2 Bedienungsanleitung