Uni-Mig RAZOR MULTI 175 Bedienungsanleitung

MULTI

U11007K / U11008K |Operating Manual

RAZOR MULTI 175/220

OPERATING MANUAL

1. Safety 3

2. Machine Features 7

3. Package Contents 8

4. Machine Speciﬁcations 9

4.1RAZOR MULTI 175 9

4.2RAZOR MULTI 220 9

5. Machine Layout 10

5.1Front Panel Layout 10

5.2Rear Panel Layout 10

5.3Interior Layout 11

5.4Geared Wire Drive System 12

6. Control Panel Layout 13

7. Control Panel Details 14

8. Advanced Settings Menu 16

9. MIG MANUAL MODE 17

10. SYNERGIC MODE 17

11. MIG: Machine Setup 18

12. MIG Welding Further Explained 25

13. TIG: Machine Setup 32

14. TIG Welding Guide 36

15. MMA: Machine Setup 40

16. MMA: Welding Guide 43

17. MIG Trouble Shooting 45

18. TIG Troubleshooting 47

19. MMA (STICK) Troubleshooting 48

20. Factory Reset 50

21. Indicator Lights 50

22. Error Codes 50

23. Wiring Diagrams 51

24. Machine Breakdown and Parts List 52

RAZOR MULTI 175/220

OPERATING MANUAL

1. Safety

Welding and cutting equipment can be dangerous to both the operator and people in or near the surrounding working

area if the equipment is not correctly operated. Equipment must only be used under the strict and comprehensive

observance of all relevant safety regulations.

Read and understand this instruction manual carefully before the installation and operation of this equipment.

Machine operating safety

• Do not switch the function modes while the machine is operating. Switching of the function modes during welding can

damage the machine. Damage caused in this manner will not be covered under warranty.

• Disconnect the electrode-holder cable from the machine before switching on the machine, to avoid arcing should the

electrode be in contact with the workpiece.

• Operators should be trained and or qualiﬁed.

Electric shock: it can kill

• Touching live electrical parts can cause fatal shocks or severe burns. The electrode and work circuit is electrically live

whenever the output is on. The input power circuit and internal machine circuits are also live when power is on. In MIG/

MAG welding, the wire, drive rollers, wire feed housing, and all metal parts touching the welding wire are electrically live.

Incorrectly installed or improperly grounded equipment is dangerous.

• Connect the primary input cable, according to Australian and New Zealand standards and regulations.

• Avoid all contact with live electrical parts of the welding/cutting circuit, electrodes and wires with bare hands.

• The operator must wear dry welding gloves while he/she performs the welding/cutting task.

• The operator should keep the workpiece insulated from himself/herself.

• Keep cords dry, free of oil and grease, and protected from hot metal and sparks.

• Frequently inspect input power cable for wear and tear, replace the cable immediately if damaged, bare wiring is dangerous

and can kill.

• Do not use damaged, undersized, or badly joined cables.

• Do not drape cables over your body.

• We recommend (RCD) safety switch is used with this equipment to detect any leakage of current to earth.

Fumes and gases are dangerous

• Smoke and gas generated while welding or cutting can be harmful to people’s health. Welding produces fumes and gases.

Breathing these fumes and gases can be hazardous to your health.

• Do not breathe the smoke and gas generated while welding or cutting, keep your head out of the fumes.

• Keep the working area well ventilated, use fume extraction or ventilation to remove welding/cutting fumes and gases.

• In conﬁned or heavy fume environments always wear an approved air-supplied respirator.

• Welding/cutting fumes and gases can displace air and lower the oxygen level, causing injury or death. Be sure the breathing

air is safe.

• Do not weld/cut in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with

vapours to form highly toxic and irritating gases.

• Materials such as galvanised, lead, or cadmium plated steel, containing elements that can give o toxic fumes when welded/

cut. Do not weld/cut these materials unless the area is very well ventilated, and or wearing an air-supplied respirator.

Arc rays: harmful to people’s eyes and skin

• Arc rays from the welding/cutting process produce intense visible and invisible ultraviolet and infrared rays that can burn

eyes and skin.

• Always wear a welding helmet with the correct shade of ﬁlter lens and suitable protective clothing, including welding gloves

while the welding/cutting operation is performed.

• Measures should be taken to protect people in or near the surrounding working area. Use protective screens or barriers to

protect others from ﬂash, glare and sparks; warn others not to watch the arc.

RAZOR MULTI 175/220

OPERATING MANUAL

Fire hazard

• Welding/cutting on closed containers, such as tanks, drums, or pipes, can cause them to explode. Flying sparks from the

welding/cutting arc, hot workpiece, and hot equipment can cause ﬁres and burns. Accidental contact of the electrode

to metal objects can cause sparks, explosion, overheating, or ﬁre. Check and be sure the area is safe before doing any

welding/cutting.

• The welding/cutting sparks & spatter may cause ﬁre, therefore remove any ﬂammable materials well away from the working

area. Cover ﬂammable materials and containers with approved covers if unable to be moved from the welding/cutting area.

• Do not weld/cut on closed containers such as tanks, drums, or pipes, unless they are correctly prepared according to the

required Safety Standards to ensure that ﬂammable or toxic vapours and substances are totally removed, these can cause

an explosion even though the vessel has been “cleaned”. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

• Do not weld/cut where the atmosphere may contain ﬂammable dust, gas, or liquid vapours (such as petrol)

• Have a ﬁre extinguisher nearby and know how to use it. Be alert that welding/cutting sparks and hot materials from welding/

cutting can easily go through small cracks and openings to adjacent areas. Be aware that welding/cutting on a ceiling, ﬂoor,

bulkhead, or partition can cause a ﬁre on the hidden side.

Gas cylinders

• Shielding gas cylinders contain gas under high pressure. If damaged, a cylinder can explode. Because gas cylinders usually

are part of the welding/cutting process, be sure to treat them carefully. CYLINDERS can explode if damaged.

• Protect gas cylinders from excessive heat, mechanical shocks, physical damage, slag, open ﬂames, sparks, and arcs.

• Ensure cylinders are held secure and upright to prevent tipping or falling over.

• Never allow the welding/cutting electrode or earth clamp to touch the gas cylinder, do not drape welding cables over the cylinder.

• Never weld/cut on a pressurised gas cylinder, it will explode and kill you.

• Open the cylinder valve slowly and turn your face away from the cylinder outlet valve and gas regulator.

Gas build-up

• The build-up of gas can cause a toxic environment, deplete the oxygen content in the air resulting in death or injury. Many

gases use in welding/cutting are invisible and odourless.

• Shut o shielding gas supply when not in use.

• Always ventilate conﬁned spaces or use approved air-supplied respirator.

Electronic magnetic ﬁelds

• MAGNETIC FIELDS can aect Implanted Medical Devices.

• Wearers of Pacemakers and other Implanted Medical Devices should keep away.

• Implanted Medical Device wearers should consult their doctor and the device manufacturer before going near any electric

welding, cutting or heating operation.

Noise can damage hearing

• Noise from some processes or equipment can damage hearing.

• Wear approved ear protection if noise level is high.

Hot parts

• Items being welded/cut generate and hold high heat and can cause severe burns.

• Do not touch hot parts with bare hands. Allow a cooling period before working on the welding/cutting gun. Use insulated

welding gloves and clothing to handle hot parts and prevent burns.

RAZOR MULTI 175/220

OPERATING MANUAL

Caution

Working environment

• The environment in which this welding/cutting equipment is installed must be free of grinding dust, corrosive chemicals,

ﬂammable gas or materials etc., and at no more than a maximum of 80% humidity.

• When using the machine outdoors, protect the machine from direct sunlight, rainwater and snow, etc.; the temperature

of the working environment should be maintained within -10°C to +40°C.

• Keep this equipment 30cm distant from the wall.

• Ensure the working environment is well ventilated.

Safety tips

• Ventilation: This equipment is small-sized, compact in structure, and of excellent performance in amperage output.

The fan is used to dissipate heat generated by this equipment during the welding/cutting operation. Important: Maintain

good ventilation of the louvres of this equipment. The minimum distance between this equipment and any other objects

in or near the working area should be 30 cm. Good ventilation is of critical importance for the normal performance and

service life of this equipment.

• Thermal Overload Protection: Should the machine be used to an excessive level, or in a high-temperature

environment, poorly ventilated area or if the fan malfunctions the Thermal Overload Switch will be activated, and the

machine will cease to operate. Under this circumstance, leave the machine switched on to keep the built-in fan working

to bring down the temperature inside the equipment. The machine will be ready for use again when the internal

temperature reaches a safe level.

• Over-Voltage Supply: Regarding the power supply voltage range of the machine, please refer to the “Main parameter”

table. This equipment is of automatic voltage compensation, which enables the maintaining of the voltage range within

the given range. In case that the voltage of input power supply amperage exceeds the stipulated value, it is possible to

cause damage to the components of this equipment. Please ensure your primary power supply is correct.

• Do not come into contact with the output terminals while the machine is in operation. An electric shock may occur.

Maintenance

Exposure to extremely dusty, damp, or corrosive air is damaging to the welding/cutting machine. To prevent any possible

failure or fault of this welding/cutting equipment, clean the dust at regular intervals with clean and dry compressed air of

required pressure.

Please note that: lack of maintenance can result in the cancellation of the guarantee; the guarantee of this welding/

cutting equipment will be void if the machine has been modiﬁed, attempt to take apart the machine or open the factory-

made sealing of the machine without the consent of an authorized representative of the manufacturer.

Troubleshooting

Caution: Only qualiﬁed technicians are authorized to undertake the repair of this welding/cutting equipment. For your

safety and to avoid Electrical Shock, please observe all safety notes and precautions detailed in this manual.

RAZOR MULTI 175/220

OPERATING MANUAL

Attention! - Check For Gas Leakage

At initial set up and at regular intervals we recommend to check for gas leakage

Recommended procedure is as follows:

1. Connect the regulator and gas hose assembly and tighten all connectors and clamps.

2. Slowly open the cylinder valve.

3. Set the ﬂow rate on the regulator to approximately 8-10 L/min.

4. Close the cylinder valve and pay attention to the needle indicator of the contents pressure gauge on the regulator,

if the needle drops away towards zero there is a gas leak. Sometimes a gas leak can be slow and to identify it

will require leaving the gas pressure in the regulator and line for an extended time period. In this situation it is

recommended to open the cylinder valve, set the ﬂow rate to 8-10 L/min, close the cylinder valve and check after a

minimum of 15 minutes.

5. If there is a gas loss then check all connectors and clamps for leakage by brushing or spraying with soapy water,

bubbles will appear at the leakage point.

6. Tighten clamps or ﬁttings to eliminate gas leakage.

IMPORTANT! - We strongly recommend that you check for gas leakage prior to operation of your machine. We

recommend that you close the cylinder valve when the machine is not in use.

Welding Guns Of Australia PTY LTD, authorised representatives or agents of Welding Guns Of Australia PTY LTD

will not be liable or responsible for the loss of any gas.

RAZOR MULTI 175/220

OPERATING MANUAL

2. Machine Features

HD Backlit Interface

Experience a new level of convenience with our next-

generation interface panel. With its vibrant and easy-to-read

display, you'll be able to eortlessly navigate and customise

your welding settings in any lighting condition.

Synergic MIG Control

Say goodbye to complicated and time-consuming setup

with our innovative Synergic MIG control. This cutting-edge

technology automatically adjusts your welding settings based

on your wire type, gas, wire size, and material thickness,

ensuring precise and ecient results every time.

Digital Control MIG Torch

The ultimate solution for welders seeking unprecedented

control and precision in their work. No more hassle of

constantly adjusting your settings on a separate control panel.

With our leading technology, you can easily ﬁne-tune your

amps, wire speed, and voltage right on the MIG torch itself.

Spool Gun Ready

You have the option of attaching a Spool Gun to run softer

core wires such as aluminium MIG wire. You don’t even need

to change the setup of your existing torch or drive roller.

Gas & Gasless MIG

Our welding machine supports both gas-shielded and gasless

MIG wire, allowing you to tackle a wide variety of welding

projects with ease. Whether you're working with mild steel,

stainless steel, aluminium, or ﬂux-cored wire, our machines

have got you covered.

Geared Wire Drive

Experience smooth and consistent wire feed with our

advanced geared roller drive unit. This feature ensures that

your wire is fed consistently and accurately, even when using

longer MIG torches.

Multi-Process Welding

Get the job done quickly and eciently with our versatile

three-in-one welding machine. With the ability to perform MIG,

TIG, and STICK welding all in one unit, you can save valuable

time and eort without sacriﬁcing quality.

Foot Control Ready

Enjoy greater control and precision with our optional foot

control accessory. This handy feature allows you to easily

adjust your TIG amperage on the ﬂy, without interrupting your

torch movement.

Trigger Controlled DC Lift Arc TIG

With Trigger Controlled DC Lift Arc ignition, starting your

welding projects has never been easier. Our Lift Arc TIG

technology ensures that your tungsten tip won't stick to the

work piece, preventing costly tip breakages.

Smart Fan

Our advanced Smart Fan technology reduces noise, saves

power, and minimises contaminants, making it the perfect

choice for any welding environment.

Advanced MMA Features

The RAZOR MULTI 175/220 features adjustable Arc Force

and Hot Start functionality. These features are designed for

improving weld quality and ease of use.

Optional Remote Control

Upgrade your machine with a handy remote control. Both a

wired and wireless controller are available.

Generator Compatible

Minimum 11 kVA (175), or 12 kVA (220) recommended.

RAZOR MULTI 175/220

OPERATING MANUAL

Includes:

• 0.8-0.9mm "V GROOVE" 30/22

• 0.8-0.9mm "F GROOVE" 30/22

• 1.0-1.2mm "U GROOVE" 30/22

3. Package Contents

RAZOR MULTI 175/200 4m Electrode Holder

4m 300 AMP Earth Clamp

Twin Gauge Argon Regulator

Drive Roller

15A Plug Fitted

4m M24 Digital MIG Torch

RAZOR MULTI 175/220

OPERATING MANUAL

4. Machine Speciﬁcations

4.1 RAZOR MULTI 175 4.2 RAZOR MULTI 220

Technical Data

Parameter Values

SKU U11007K

Primary Input Voltage 240V Single Phase

Supply Plug 15 AMP

Ie (A) 15

Rated Output 30A/15.5V - 175A/22.8V

No Load Voltage (V) 60

Protection Class IP23S

Insulation Class H

Minimum Generator (kVA) 11.0

Dinse Connector 35/50

Standard AS/NZ60974-1

Warranty (Years) 5

MIG Speciﬁcations

MIG Welding Current Range 30-175A

MIG Duty Cycle @ 40°C 25% @ 175A

60% @ 101A

100% @ 78A

MIG Welding Thickness Range 1-8mm

TIG Speciﬁcations

TIG Function Type DC Lift Arc

TIG Welding Current Range 5-175A

TIG Duty Cycle @ 40°C 25% @ 175A

60% @ 113A

100% @ 88A

TIG Welding Thickness Range 1-6mm

STICK Speciﬁcations

STICK Welding Current Range 20-160A

STICK Duty Cycle @ 40°C 20% @ 160A

60% @ 93A

100% @ 72A

STICK Welding Thickness Range 2-10mm

Size & Weight

Dimensions (mm) 560×220×40

Weight (kg) 15.0

Technical Data

Parameter Values

SKU U11008K

Primary Input Voltage 240V Single Phase

Supply Plug 15 AMP

Ie (A) 14.7

Rated Output 30A/15.5V - 220A/25V

No Load Voltage (V) 60

Protection Class IP23S

Insulation Class H

Minimum Generator (kVA) 12.0

Dinse Connector 35/50

Standard AS/NZ60974-1

Warranty (Years) 5

MIG Speciﬁcations

MIG Welding Current Range 30-220A

MIG Duty Cycle @ 40°C 15% @ 220A

60% @ 110A

100% @ 85A

MIG Welding Thickness Range 1-10mm

TIG Speciﬁcations

TIG Function Type DC Lift Arc

TIG Welding Current Range 5-220A

TIG Duty Cycle @ 40°C 15% @ 220A

60% @ 110A

100% @ 85A

TIG Welding Thickness Range 1-8mm

STICK Speciﬁcations

STICK Welding Current Range 20-180A

STICK Duty Cycle @ 40°C 15% @ 180A

60% @ 90A

100% @ 70A

STICK Welding Thickness Range 2-12mm

Size & Weight

Dimensions (mm) 560×220×400

Weight (kg) 15.1

Capable Welding Material Types By Welding Process

Mild Steel, Stainless Steel, Cast IronMild Steel, Stainless Steel, Copper,

Silicon Bronze

Mild Steel, Stainless Steel, Aluminium,

Silicon Bronze

MIG: TIG: MMA:

RAZOR MULTI 175/220

OPERATING MANUAL

5. Machine Layout

5.1 Front Panel Layout

1. Interface Panel

2. “+” Output Terminal

3. “-” Output Terminal

4. Euro Connect Torch Port

5. Wired Remote Connection Port

6. Polarity Cable

7. Wireless Remote Indicator

5.2 Rear Panel Layout

8. On/O Switch

9. Gas Input

10. Input Power Cord

Dieses Handbuch passt für folgende Modelle

Andere Uni-Mig Schweißsystem Handbücher

Uni-Mig

Uni-Mig KUMJRRW175MIG Bedienungsanleitung

Uni-Mig

Uni-Mig ARC 170DC Bedienungsanleitung

Uni-Mig

Uni-Mig KUMJR200AC/DC Bedienungsanleitung

Uni-Mig

Uni-Mig Arclite KUMJRAL140 Bedienungsanleitung

Uni-Mig

Uni-Mig RAZOR TIG 200 AC/DC Bedienungsanleitung

Uni-Mig

Uni-Mig UNI-PLAS 50/80 Bedienungsanleitung

Uni-Mig

Uni-Mig KUMJRRW200DC Bedienungsanleitung

Uni-Mig

Uni-Mig KMM180 Bedienungsanleitung

Uni-Mig

Uni-Mig RAZOR ARC140 Bedienungsanleitung

Uni-Mig

Uni-Mig Workshop 270SWF Bedienungsanleitung

Uni-Mig

Uni-Mig KUMJRRW140 Bedienungsanleitung

Uni-Mig

Uni-Mig KUMJRDP210 Bedienungsanleitung

Uni-Mig

Uni-Mig 390 Bedienungsanleitung

Uni-Mig

Uni-Mig PRO-CRAFT240 MIG Bedienungsanleitung

Uni-Mig

Uni-Mig WORKSHOP 390SWF Bedienungsanleitung

Uni-Mig

Uni-Mig 425SWF Bedienungsanleitung

Uni-Mig

Uni-Mig RAZOR ARC 140 Bedienungsanleitung

Uni-Mig

Uni-Mig KUMJRRW165MIG Bedienungsanleitung

Uni-Mig

Uni-Mig RAZOR 320 AC/DC Bedienungsanleitung

Uni-Mig

Uni-Mig CUT40 Bedienungsanleitung

Uni-Mig

Uni-Mig RAZORCut 45 Bedienungsanleitung

Uni-Mig

Uni-Mig RAZOR CUT 45 PFC Bedienungsanleitung

Uni-Mig

Uni-Mig 270 Compact Bedienungsanleitung

Uni-Mig

Uni-Mig 500SWF Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung