UnionTech Martrix Series Bedienungsanleitung
UT-PM-LCD-UM-2022-Mar
Martrix Series
User Manual
UT-PM-LCD-UM-2022-Mar
UT-PM-LCD-UM-2022-Mar
Thank you for using our products!
Third-party registered trademark: Shanghai Union Technology Corporation
(UNIONTECK) declares that all trademarks are the property of their legal owners.
Shanghai Union Technology Corporation hereby declares that, all the information
provided in this document is correct at the time of printing, and subject to change due
to improvements in performance and quality of the product without prior notice.
Shanghai Union Technology Corporation declares that it assumes no responsibility for
possible mistakes in this Manual.
The content of this document shall be strictly kept confidential, and its owner is
responsible for using it for its own purpose.
This Manual cannot be given, leased or copied in whole or in part to others without
written authorization of Shanghai Union Technology Corporation.
Shanghai Union Technology Corporation
Shanghai Headquarters
Room 102, Building 40, No. 258 Xinzhuan Rd.,Songjiang High Science & Technology
Park, Caohejing Developing Zone, Shanghai (201612)
Tel: 021-64978786
Fax: 021-64978786-8180
Website: www.uniontech3d.cn
UT-PM-LCD-UM-2022-Mar
Foreword
This Manual is a user manual designed for Martrix520/Martrix190 3D printer.
It comprehensively describes main principles, technical, structural and design
characteristics, precautions, and post processing of 3D printer, and contains guidelines
for application and maintenance of equipment.
Besides of hardware structure of equipment, this Manual also contains information
about control system, data preparation software and optional post processing tools.
UT-PM-LCD-UM-2022-Mar
Contents
1. Safety Alert ................................................................................................................ 1
2. Introduction ................................................................................................................2
2.1 Product Overview ............................................................................................ 2
2.2 Packing list .......................................................................................................3
3. The Touchscreen User interface .................................................................................5
3.1 Print Interface .................................................................................................. 5
3.2 Control Interface .............................................................................................. 5
3.3 Functional Interface ......................................................................................... 7
3.4 Hardware Interface .......................................................................................... 7
4. Workspace Preparation and Initial Setup ................................................................... 9
4.1 Resin Tank Membrane Change and Installation Instructions .......................... 9
4.2 Leveling ......................................................................................................... 10
5. Onboarding and First Print ...................................................................................... 13
5.1 Data processing software ............................................................................... 13
5.1.1 Installation of Polydevs DLP ..............................................................13
5.1.2 Introduction to polydevs DLP function modules ................................14
5.1.3 Introduction to the usage process ........................................................16
5.2 On-board process ........................................................................................... 24
5.3 Disembarkation process ................................................................................. 25
6. Machine screen change operation method ...............................................................28
6.1 Remove the fixing screws ..............................................................................28
6.2 Replace the cable ........................................................................................... 28
6.3 Mounting screws ............................................................................................28
6.4 Pallet leveling ................................................................................................ 29
6.5 Adjust software parameters ............................................................................29
6.6 Check the screen ............................................................................................ 30
6.7 Install the resin tank .......................................................................................30
6.8 Replace the process package ..........................................................................30
7. FAQ ..........................................................................................................................30
7.1 Troubleshooting of printer ..........................................................................30
7.2 Troubleshooting of building part ................................................................32
8. Care & Maintenance ................................................................................................ 34
UT-PM-LCD-UM-2022-Mar
8.1 Regular maintenance procedure .....................................................................34
8.2 Precautions for daily operation and use .....................................................34
9. After-sales service & warranty .................................................................................36
FCC WARNING .......................................................................................................... 37
UT-PM-LCD-UM-2022-Mar
1
1. Safety Alert
1) Receipt to determine the appearance and mechanical structure of the machine.
2) When removing the printed model from the platform with a shovel, be careful not
to put your hand in the forward direction of the shovel.
3) In case of emergency, turn off the power of the machine directly.
4) Do not touch the moving parts of the machine when the machine is in motion to
prevent pinching.
5) Wear gloves and goggles when filling resin and post-processing the model.
6) The printer and consumables should be placed out of the reach of children to
prevent pinching and accidental drinking of resin.
7) Please use the printer in a well-ventilated environment and place the machine on
a level platform.
8) When not in use for a long time, the resin in the machine should be emptied, and
the machine should be kept out of moisture when it is sealed.
9) When printing, it is recommended to control the ambient temperature between
10°C-40°C and the humidity between 20%-40%. Exceeding the recommended range
may cause some printing problems.
10) When there is a problem with the machine hardware, please contact the
after-sales service, and do not disassemble the machine without permission.
UT-PM-LCD-UM-2022-Mar
2
2. Introduction
2.1 Product Overview
The overall appearance of the machine is shown in Figure 2.1 below:
Figure 2.1 Overall appearance of the machine
The structure of the back of the machine is introduced as shown in Figure 2.2
below:
Figure 2.2 Machine back structure
Cooling fan
Power cord interface
main switch
Cooling fan
Cable interface
WIFI interface
UT-PM-LCD-UM-2022-Mar
3
The internal structure of the Martrix machine is shown in Figure 2.3 below:
Figure 2.3 Internal structure
2.2 Packing list
Name
Quantity
Application/Remark
Martrix LCD Printer
1PC
Martrix 520 or 190
Silicone scraper
1PC
For cleaning residual resin in resin tanks
Plastic tweezers
1PC
Used to strip debris and clean up flakes
produced
0.1mm Feeler gauge
1PC
For adjusting pallet level
Spatula
1PC
Blade width 15mm, for shovel samples
Magnetic door switch
Pallet
Filter fan
Heating fan
Filter fan
Resin tank fixing handle
Screen and mounting plate
USB interface
Flashlight
Thermomete
Camera
Display
Power-on touch key
UT-PM-LCD-UM-2022-Mar
4
Metric Allen Wrench
Six-Piece Set
1Unit
1.5/2.5/3/4/5#, for leveling pallets, changing
screens, etc
200 mesh filter
1PC
For filter resin
Gloves
1Box
To stay safe and clean
U disk
1PC
For test documents & model storage
Tool Box
1PC
For tools storage
Watering Can
1PC
For alcohol cleaning use（250ml）
Screen film
5PCS
For LCD screen protection
Diagonal pliers
1PC
Used to strip debris and clean up flakes
produced
Release film
5PCs
Used to replace damaged membranes on
resin tanks
Table 2.1 Packing list
Inhaltsverzeichnis
