Unit UT90A Bedienungsanleitung
Model UT90A: OPERATING MANUAL=VC220
1
Table of Contents
Title Page
Overview
Unpacking Inspection
Safety Information
Rules For Safe Operation
International Electrical Symbols
The Meter Structure
LCD Indicators
Rotary Switch
Functional Buttons
Measurement Operation
A. AC/DC Voltage Measurement
B. AC/DC Current Measurement
C. Resistance Measurement
D. Diodes Measurement
E. Continuity Measurement
F. Power Voltage Measurement
General Specifications
Accuracy Specifications
A. DC Voltage
B. AC Voltage
C. DC Current
D. AC Current
E. Resistance
F. Diodes Test
G. Continuity Test
Fuse Replacement
Maintenance
Model UT90A: OPERATING MANUAL
2
Overview
This Operating Manual covers information on
safety and cautions. Please read the relevant
information carefully and observe all the
Warnings and Notes strictly.
Warning
To avoid electric shock or personal injury,
read the “Safety Information” and “Rules for
Safety Operation” carefully before using the
Meter.
The Model UT90A(hereafter referred to as “the
Meter”) is a 1999 counts low power waste
electrical tester with and stabilize functions,
safety operations, and reliable performance.
In addition to the conventional measuring
function, such as DC/AC voltage, resistance,
diode and continuity and power voltage test, it is
also a highly applied digital electrical tester of
good performance with big size full functions
symbols indication, full overload protection and
special appearance.
Unpacking Inspection
Open the package case and take out the Meter.
Check the following items carefully to see any
missing or damaged part:
Item
Description
Qty
1
Operating Manual
1
piece
2
Test Lead
1
pair
Model UT90A: OPERATING MANUAL
3
3
certificate
1 piece
In the event you find any missing or damage,
please contact your dealer immediately.
Safety Information
This Meter complies with GB4793 standard for
safety electrical measuring and test equipment,
and IEC61010-1: in pollution degree 2,
overvoltage category (CAT II 1000V, CAT III
600V) and double insulation.
Use the Meter only as specified in this operating
manual, otherwise the protection provided by the
Meter may be impaired.
In this manual, a Warning identifies conditions
and actions that pose hazards to the user, or
may damage the Meter or the equipment under
test.
A Note identifies the information that user should
pay attention on.
International electrical symbols used on the
Meter and in this Operating Manual are
explained on page XXX.
Rules For Safe Operation
Warning
To avoid possible electric shock or personal
injury, and to avoid possible damage to the
Meter or to the equipment under test, adhere
Model UT90A: OPERATING MANUAL
4
to the following rules:
lBefore using the Meter inspect the
case. Do not use the Meter if it is
damaged or the case (or part of the
case) is removed. Look for cracks or
missing plastic. Pay attention to the
insulation around the connectors.
lInspect the test leads for damaged
insulation or exposed metal. Check the
test leads for continuity. Replace
damaged test leads with identical
model number or electrical
specifications before using the Meter.
lWhen using the test leads, keep your
fingers behind the finger guards.
lDo not apply more than the rated
voltage, as marked on the Meter,
between the terminals or between any
terminal and grounding.
lWhen the Meter working at an effective
voltage over 60V in DC or 30V in AC,
special care should be taken from there
is danger of electric shock.
lUse the proper terminals, function, and
range for your measurements.
lThe rotary switch should be placed in
the right position and no any
changeover of range shall be made
during measurement is conducted to
prevent damage of the Meter.
lDisconnect circuit power and discharge
all high-voltage capacitors before
testing resistance, diodes or continuity.
lCharge as soon as the Meter indicator
appears to keep precision of the
Model UT90A: OPERATING MANUAL
5
readings.
lRemove test leads from the test circuit
before changeover of range. Turn the
Meter power off before connect the
Meter to circuit and check the fuse
before measuring current.
lWhen servicing the Meter, use only the
same model number or identical
electrical specifications replacement
parts.
lThe internal circuit of the Meter shall not
be altered will to avoid damage of the
Meter and any accident.
lSoft cloth and mild detergent should be
used to clean the surface of the Meter
when servicing. No abrasive and solvent
should be used to prevent the surface of
the Meter from corrosion, damage and
accident.
lTurn off the Meter when it is not in use
for a long time.
lDo not use or store the Meter in an
environment of high temperature,
humidity, explosive, inflammable and
strong magnetic field. The performance
of the Meter may deteriorate after
dampened.
International Electrical Symbols
AC (Alternating Current).
DC (Direct Current).
Grounding.
Double Insulated.
Model UT90A: OPERATING MANUAL
6
Deficiency of Built-In Battery.
Warning. Refer to the Operating
Manual.
China Technology Supervision
Bureau, license for measuring
instrument Manufacture
Conforms to Standards of European
Union.
The Meter Structure (see figure 1)
?LCD Display.
?Impedance changeover button.
?Rotary Switch.
?Input Terminals.
?Power Button.
LCD indicators(see figure 2)
?~appear at AC measurement, disappear
at DC measurement.
?display the minus readings.
?high voltage indicator.
?battery deficiency indicator.
?continuity measurement indicator.
?diodes measurement indicator.
?Connect Terminal terminal connect indicator.
?
O?KO?MOResistance unit
MV?VVoltage unit
µA?mA?ACurrent unit
Rotary Switch
Model UT90A: OPERATING MANUAL
7
Below table indicated for information about the
rotary switch positions.
Rotary
Switch
Positio
n
Function
V DC voltage measurement range
from 200.0mV to 1000V.
VAC voltage measurement range
from 2.000V to 750.0V.
OOResistance measurement range
from 200.0Oto 20.00MO.
Diode test.
Continuity test.
ADC current measurement range
from 200.0mA to 20.00A.
AAC current measurement range
from 200.0µA to 20.00A.
Power voltage measurement
Turn on/off the Meter.
Functional Buttons
Below table indicated for information about the
functional button operations.
Button Measur
ing
Functi
on
Operation Performed
Model UT90A: OPERATING MANUAL
8
Impeda
nce
change
over
button
AC/DC
voltage
range
It is used to inspect
the resistance of
supply power under
250V
MAX.(??????)
Any
rotary
switch
position
Turn the power of the
Meter on or off.
Measurement Operation
A.AC/DC Voltage Measurement (see figure
3)
Warning
To avoid harms to you or damages to the
Meter from electric shock, please do not
attempt to measure voltages higher than
1000V DC/750V AC although readings may be
obtained.
Impedance Changeover Button turn on time
should=3 seconds. To avoid damages to the
Meter, please do not use the Impedance
Changeover Button when the measured
voltage is higher than 250V.
The DC voltage ranges are: 200.0mV, 2.000V,
20.00V, 200.0V, 1000V; The AC voltage ranges
are: 2.000V, 20.00V, 200.0V, 750.0V. To measure
Model UT90A: OPERATING MANUAL
9
AC/DC voltage, connect the Meter as follows:
1. Insert the red test lead into the“VO)”
terminal and the black test lead into the
COM terminal.
2. Set the rotary switch to“V”or“V”,and
Connect the test leads across with the
power or load being measured.
3. The measured value shows on the
display,which is an effective value of sine
wave (mean value response).
4. In each range, the Meter has an input
impedance of 10MO. This loading effect
can cause measurement errors in high
impedance circuits. If the circuit impedance
is less than or equal to 10kO, the error is
negligible (0.1% or less).
5. Manual Impedance Changeover
Button“10MO/400kO”can be used to check
inside impedance of supply power under
250V MAX.
Note
lWhenAC/DC voltage measurement has
been completed, disconnect the connection
between the testing leads and the circuit
under test.
lPay attention to avoid harms to you from
electric shock during high voltages
measurement.
B.AC/DC Current Measurement (see figure
4)
Warning
Model UT90A: OPERATING MANUAL
10
To avoid damages to the built-in fuse and the
Meter, please do not attempt parallel connect
the test leads with any circuit while the test
leads are inserted into the current terminal.
For the safety requirement, when measure
high current, every measure time should<10
seconds and the time between two
measurements should >15 minutes.
The measurement ranges of DC current are:
200mA,2mA,20mA,200mA,20A; The
measurement ranges of AC current are:
200.0µA,2.000mA,20.00mA,200.0mA and
20.00A. To measure current, do the following:
1Insert the red test lead into the“µA
mA ”or“20A”terminal and the black test
lead into the COM terminal.
2Set the rotary switch to“A”or“A”,and
Connect the test leads across with the
circuit being measured.
3. The measured value shows on the display,
it is an effective value of sine wave (mean
value response).
Note
lTurn off the power of circuit being
measured before series connection
between the Meter and the circuit.
lUse proper terminals and ranges for the
measurement.
lPlease use the ranges from high to low if
the current not being confirmed.
lWhen current measurement has been
Andere Handbücher für UT90A
2
Inhaltsverzeichnis
Andere Unit Multimeter Handbücher
Unit
Unit UT58A Bedienungsanleitung
Unit
Unit UT232 Bedienungsanleitung
Unit
Unit UT207A Bedienungsanleitung
Unit
Unit UT39B Bedienungsanleitung
Unit
Unit UT70D Bedienungsanleitung
Unit
Unit UT60H Bedienungsanleitung
Unit
Unit UT51 Bedienungsanleitung
Unit
Unit UT205A Bedienungsanleitung
Unit
Unit UT501 Bedienungsanleitung
Unit
Unit UT202A Bedienungsanleitung
Unit
Unit UT51-55 Bedienungsanleitung
Unit
Unit UT131A Bedienungsanleitung
Unit
Unit UT8806E Bedienungsanleitung
Unit
Unit UT90B Bedienungsanleitung
Unit
Unit UT-33D+ Bedienungsanleitung
Unit
Unit UT57 Bedienungsanleitung
Unit
Unit UT71B Bedienungsanleitung
Unit
Unit UT106 Bedienungsanleitung
Unit
Unit UT71A Bedienungsanleitung
Unit
Unit UT58D Bedienungsanleitung
Beliebte Multimeter Handbücher anderer Marken
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Bedienungsanleitung
PeakTech
PeakTech 4000 Gebrauchs- und Pflegehandbuch
YOKOGAWA
YOKOGAWA 90050B Bedienungsanleitung
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung
Fluke
Fluke 8846A Bedienungs- und Wartungshandbuch
Tempo Communications
Tempo Communications MM200 Bedienungsanleitung
