UUGear PiGear Nano Bedienungsanleitung

UUGear is a trade name of Dun Cat B.V.

PiGear Nano:

Nano-ITX Raspberry Pi Compute Module 4 Carrier Board

User Manual (revision 1.04)

UUGear is a trade name of Dun Cat B.V.

Table of Contents

1. Product Overview ...............................................................................................................1

2. Specification / Technical Details..........................................................................................3

3. Package Content................................................................................................................4

4. Connect Raspberry Pi Compute Module 4 to the Board......................................................5

5. Installing Operating System................................................................................................7

5.1 For Raspberry Pi CM4 with eMMC...........................................................................7

5.2 For Raspberry Pi CM4 Lite (without eMMC).............................................................8

6. Powering PiGear Nano.......................................................................................................9

7. Software Installation / Update.............................................................................................9

8. Jumper Settings................................................................................................................11

9. Software Usage................................................................................................................14

9.1 Realtime Clock.......................................................................................................15

9.2 Analog Inputs (ADC)..............................................................................................16

9.3 Digital Inputs..........................................................................................................17

9.4 Digital Outputs .......................................................................................................18

9.5 Configurable Digital Inputs/Output..........................................................................19

9.6 Programmable LED Test........................................................................................19

9.7 Buzzer Test............................................................................................................19

9.8 UWI Usage ............................................................................................................20

10. 2x16 Quick Cable Connector.........................................................................................21

10.1 Serial Port..............................................................................................................22

10.2 Controller Area Network (CAN) Bus.......................................................................24

10.3 1-Wire Interface .....................................................................................................25

10.4 Analog Inputs (A/D Converter) ...............................................................................26

10.5 Digital Inputs..........................................................................................................30

UUGear is a trade name of Dun Cat B.V.

10.6 Digital Outputs .......................................................................................................31

10.7 Configurable Digital Inputs/Outputs........................................................................32

11. PCIE .............................................................................................................................35

11.1 NVME SSD............................................................................................................36

11.2 4G LTE Module......................................................................................................36

11.3 USB3.0 ..................................................................................................................38

12. Realtime Clock (RTC) ...................................................................................................39

13. DSI and CSI..................................................................................................................40

14. SD Card Slot.................................................................................................................41

15. LED Indicators ..............................................................................................................41

16. Buzzer...........................................................................................................................41

17. Fan Connector ..............................................................................................................42

18. Power and Reset Button Connectors ............................................................................42

19. Case Kit for PiGear Nano..............................................................................................42

20. Revision History............................................................................................................43

1. Product Overview

PiGear Nano is a high performance Nano-ITX (12x12cm) carrier board for Raspberry Pi Compute

Module 4. PiGear Nano is mainly designed for industrial applications, but you can also use it as office

computer, family media center, gaming console etc.

PiGear Nano offers a wide range of resources and interfaces. Please see below the diagram for

details:

There are also an NVME SSD M.2 connector and a SIM card slot underneath the board.

You can place PiGear Nano into a Nano-ITX computer case. Below is a mechanical drawing of the board.

2. Specification / Technical Details

Network

Gigabit-Ethernet RJ45 socket x 1

MINI PCIE LTE/4G/GPRS interface x 1

On-board SIM card slot x 1

USB

USB 3.0 Type-A connector x 8

USB 2.0 Type-C connector x 1 (for flashing CM4, or powering the board with light load)

Analog & Digital I/O

18-bit ADC input x 4

Digital input x 4

Digital output x 4

Configurable digital I/O x 4

Signal Interface

RS232 x 2

RS485 x 2

CAN x 1

Wire interface x 1

Storage

NVME SSD M.2 interface x 1

Micro SD card slot x 1 (for Compute Module 4 Lite only)

Display

HDMI Type-A connector x 1

MIPI DSI interface x 1

Camera

MIPI CSI interface x 1

Other

Real-time clock x 1 (with supper capacitor for off-power time keeping)

Buzzer x 1

Power Indicator x 1

Programmable LED indicator x 1

5V fan interface (PH2.0 connector)

Power button x 1 (with extension connector)

Reset button x 1 (with extension connector)

Power Supply

DC 7V~30V (with reverse polarity protection)

or DC 5V (via USB Type-C connector)

Quiescent Current

~1mA

Board Size and Weight

NANO-ITX 12 x 12 cm, 150g

Operating Environment

Temperature -30°C~80°C (-22°F~176°F)

Humidity 0~80%RH, no condensing

No corrosive gas

3. Package Content

Each package of PiGear Nano contains:

PiGear Nano board x 1

6x6x5 heat sink x 1 (for VL805 chip on the back of the board)

M3x8 metal standoff x 4

M3 screws x 4

M2 screws x 3

2.54-2P jumper cap x 5

4. Connect Raspberry Pi Compute Module 4 to the Board

Before starting, it is recommended to install four metal standoffs underneath so the board can lay flat

on the desk. You can find four metal standoffs and four screws in the package. Just place the

standoff under the mounting hole and use a screw to secure it.

Connect Raspberry Pi Compute Module 4 to the board by simply aligning it with the two connectors

on board (or alternatively you can align the CE marks on CM4 and the board), and then give it a good

squeeze. It will crunch into place (and you can hear it).

If you will use the device in a vibrating environment, you may want to secure your Raspberry Pi

Compute Module 4 on the board with four M2.5 screws (not included in the package).

It is also recommended to put the small heatsink (included in the package) on the VL805 chip on the

back of the board. Because this chip could get rather hot if the board is processing many USB data

translation.

You can peel off the paper on the heatsink and directly stick it on the chip VL805, as shown below:

5. Installing Operating System

5.1 For Raspberry Pi CM4 with eMMC

If your Raspberry Pi Compute Module has eMMC, you can flash the OS into its eMMC. If you want,

you can have this done with the official I/O board. However using the official I/O board is not

necessary because you can get this done on PiGear Nano board directly.

Before proceeding, please make sure to short the "bypass power switch" jumper. This is to bypass

the e-latch power switch, so your PiGear Nano board will be powered even without the operating

system. The "bypass switch" jumper is on the left of Raspberry Pi CM4 (above the "Default On"

jumper), as shown in picture below:

You will also need to short the "Disable eMMC Boot" jumper, so the eMMC on your Raspberry Pi

CM4 will boot in USB mass storage mode, and you can flash the disk image into it.

Now connect a USB Type-C cable to PiGear Nano, and connect the other end of the cable to your

computer. This USB cable will power your PiGear Nano during the installation process, and there is

no need to connect any other power supply.

Inhaltsverzeichnis

Andere UUGear Steuereinheit Handbücher

UUGear

UUGear Witty Pi 3 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung