V-Tec DT37MG Bedienungsanleitung

2 WIRE INTERCOM SYSTEM

USER MANUAL

DT-ENG-37MG/TD7-V1

ENGLISH

Please read this manual carefully before using the product, and keep it well.

1. Parts and Functions

Digital TFT LCD Screen

Connection Port

Speaker

Mounting Hook

Unlock Button

Microphone

Talk/MON Button

Menu Button

SD card

1 2 3

ON DIP

4 5 6

Key functions

Terminal Description

-1-

LCD screen Display the visitors' image

Unlock button Press to release the door

Menu button Press to open the menu shortcuts

Talk/Mon button Press to communicate hands free with visitor

Press to view the outdoor condition in standby mode

Microphone Receive voice from the user

Mounting hook Use to hang up the monitor

Connection port Bus terminal

Speaker Send out vioce from the visitor

1 2 3

ON DIP

4 5 6

1 2 3

ON DIP

4 5 6

SW+

SW-

Ring

GND

L1,L2: Bus terminal.

SW+,SW-: Door bell call button connection port.

Ring,GND: Extra buzzer connection port.

NC: Reserved.

DIP switches: Total 6 bits can be congured.

Bit1~Bit5: Used to User Code setting.

Bit6: Set to ON if the monitor is at the end of the line;

Otherwise, set to OFF.

2. Monitor Mounting

145~160 cm

3. Main Menu

Touch the touch button anywhere in

standby mode, the main menu page will

be shown as follows:

-2-

4. Basic Door Release Operation

1. Press CALL button on outdoor station, the

Monitor rings, at the same time, the screen

displays the visitors' image.

2. Press TALK/MON Button on monitor

or touch icon on screen, you can

communicate hands free with the visitor for

90 seconds.After nishing communication,press TALK/MON button again or

touch icon to end the communication. If nobody answers the phone, the screen

will be turned off automatically after 30 seconds.

00:30 Front Door

It will display the

call source string

1. Use the screws to x the Mounting Bracket on the mounting box.(tting accesories

includes a Bracket (Two pieces of 4X25 screws are needed to fasten the Mounting

Bracket), Special 2 wire connectors to connect with Monitor)

2. Wire the system correctly(refer to connection chapter) then hang the Monitor on

the Mounting Bracket rmly.

1. During talking state, Press UNLOCK Button or touch icon to open the

door for the visitor.(if two locks are connected to door camera,touch unlock

2nd icon to release the second lock )

2. When the monitor is in standby mode, press TALK/MON Button, The screen

can display the view of outside. Or touch Monitor icon on main menu to get

into the door camera switching mode, if multi door stations are installed, you can

press the door 1/2/3/4 to monitor the door station or CCTV camera you want.press

icon to exit and enter main menu page.

Note: if the system connect 2 wire camera via camera controller, press the camera

1/2/3/4 to monitor the camera you want.press icon to exit and enter main menu

page.

5. Intercom Function

1. Inner Broadcast: If multi slave monitors are installed in the same apartment, select

Inner Broadcast, all the other monitors will mandatory receive broadcast content at

the same time, whichever slave monitor doesn't need to answer the broadcast, and

whichever slave monitor also doesn't need to open the scrccn.

2. Inner Call: If multi slave monitors are installed in the same apartment, select Inner

-3-

Touch Intercom icon on main menu to get into the intercom mode , you have 4 item

to select:Inner Broadcast, Inner Call, Name List Call and Call Guard Unit.

Call, all the other Monitors will ring at the same time, whichever Monitor answers

the call, conversation is started.and the other monitors will stop ringing at the same

time.

3. Name List Call: User in one apartment can call other apartments in the system.

Touch Name List Call icon (the namelist will be created automatically by the

system) on intercom mode menu page, Select a name on the screen then touch

icon to call.Press / icon to enter last/next name list page. (Touch Dial

Number icon again to redial)

9. Call Guard Unit: A Monitor can be assigned as Guard Unit Monitor; when the Guard

Unit Monitor answers the call, conversation with the guard person is started..

6. Video/Picture Memory

-4-

[ 01 ] Jim. Zhang

[ 02 ] Calo. Liu

[ 03 ] Jacko. Zhang

[ 04 ] Philips. Chen

[ 05 ] Hebe. Zhang

[ 06 ] Tony. Li

Name List

Video/Picture Playback

Touch Playback icon on main menu, the recorded videos/pictures will be played on

screen, please note that touch icon to Start/Pause the videos recorded.

Video/Picture Recording

Both Auto-Recording and Manual-Recording are available.And Auto-Recording is

default. If receive a call , after 3s, the monitor will record one video/picture for each

calling automatically. Or you can touch icon to record the visitor's video/image

manually when the monitor is in monitoring or calling.

Note: The video/picture memory function is built into the monitor.

-5-

Image:008/020 2014/06/23 14:36:55

7. Call Record Function

Call Record:All the calls concerning the montior, including Door-station-to-monitor call,

monitor-to-monitor call, will be recored and can be reviewed afterwards.

Touch Call Record icon on main menu to get into the call record mode.When there

are unread call records, arrow color red. Press the unread call record, and then touch

icon to play it.

Call Record 01/05

06-23 15:22 Calo.Liu

06-18 20:54 Smith

06-12 11:06 Vincent.Yang

05-29 08:39 Allen.Chen

05-27 21:43 Hebe.Zhang

04-20 13:16 Ben.Wu

Call Record 01/05

06-23 15:22 Calo.Liu

06-18 20:54 Smith

06-12 11:06 Vincent.Yang

05-29 08:39 Allen.Chen

05-27 21:43 Hebe.Zhang

04-20 13:16 Ben.Wu

Note: 1.Automatic limited number of

records.

2.Do not need to delete any a

record.

Note: When the system without SD card: 1.118 pictures in inner memory

2.Manage each picture.

When the system with SD card:1.A brand new SD card needs to be formated

by the monitor, then can it be used for video recording.

2.Up to 32G Micro SD card.

3.Video & Audio record.

4.Manage each video clips.

5.Can be copied.

-6-

8. Do Not Disturb Function

Touch Do Not Disturb icon on main menu to get into the don't disturb mode ,

you have 4 item to select:Normal, For 1 Hour, For 8 Hours and Always. You can select

the appropriate item according to your needs.

Do Not Disturb

Normal

For 1 Hour

For 8 Hours

Always

Note: When you select "For 1 Hour" or "For 8 Hours", bottom of the screen will display

the remaining time.

Refuse Call In: 00:58:32

9. Divert Function

Touch Divert icon on main menu to get into the transfer mode. Touch the empty

place ,and then input the telephone number by pressing the digital keypad.And it has 3

types of divert modes:

1:Don't Transfer----calls from outdoor station will not be diverted.

2:If No Answer----outdoor station calls indoor monitor firstly,if nobody answer

the call within 30 seconds,the call will be diverted to the telephone number

you set. At this mode,the monitor will shut off immediately when TPC/GSM/

TPS divert sucessfully,while it won't affect the communication between TPC/

GSM/TPS and outdoor station.Otherwise, the monitor can do the operation of

monitoring,talking,and unlocking.

3:Simutaneously----calls from outdoor station will be diverted to your telephone

immediately.At this mode,the monitor won't shut off when TPC/GSM/TPS divert

sucessfully,but if the monitor answers the call at this time,TPC/GSM/TPS will quit

absolutely.

Transfer Options

Don't Transfer

If No Answer

Simutaneously

-7-

Note:1.Touch icon to detect the transfer device info.

2.Touch icon to send message.

10. Staircase Light

Note: the staircase light function will be activated only when the system connect light

via SC6V module, otherwise, this function is unvalid in normal. For more information,

please refer to SC6V user instruction in detail.

On main menu page or in monitoring,touch Light icon to open the staircase light, the

staircase light will be turned off automatically.

11. Basic Setup Instructions

Sounds Settings

Touch icon on main menu page(or on door camera switching mode page), then select

"Sounds" item to enter the sounds settings page.You can set a variety of ring tones on

this page.(touch icon to exit the setting and return main menu page.

Transfer Options

Don't Transfer

If No Answer

Simutaneously

Transfer Device Info

Device -

SIM -

Network -

Signal Level -

Note: Door Ring have 2 mode:United

and Seperate.If select "United",it means

Door1/2/3/4 as a whole to adjust the ring

tones.

-8-

Date & Time Settings

Touch icon on main menu page(or on door camera switching mode page), then select

"Date & Time"item to enter the date & time settings page.You can set the date &

time on this page.(touch icon to exit the setting and return main menu page.

Note: You can set your own time, you

can also synchronize the system time.

Rename & Monitor Time Settings

Touch icon on main menu page(or on door camera switching mode page), then select

"More..."item to enter the Rename & monitor time settings page.You can set door

station rename, camera rename, monitor time on this page.(touch icon to exit the

setting and return main menu page.

-9-

Note: If you want to rename, please touch the place of name, then it will turn keypad

page ,you can input your new name in this page.

DOOR3 RENAME abc

DS-3_

During monitoring or talking state, touch icon,the Adjust page will be displayed.

1. The Scene mode selection: Total 4 screen

modes can be selected in sequence:

Normal,

Brightly, Soft

and

User.

Whenever you modify

Brightness

colour, Scene

item will be set to

User

mode automatically.

2. Note that all the modications will be performed immediately after the operation.

Touch the window of image to exit the adjust page.

Screen and Volume Adjustment

The restore to default function allows the user to recover the settings to factory setting.

Note that the restore to default operation will not change the setting and datas.

Enter main menu page,and touch icon, then select "About" item (or touch logo

position) to enter the about settings page, touch icon, the default settings will be

loaded.

touch icon to enter the Memo Information page, touch and icon to copy the

pictures to SD card. Touch and icon to format SD card and restart.

12. Restore to Default

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere V-Tec Gegensprechanlage Handbücher

V-Tec

V-Tec 27SDTD7-V1 Bedienungsanleitung

V-Tec

V-Tec DT24 Series Bedienungsanleitung

V-Tec

V-Tec 27TD7-V1 Bedienungsanleitung

V-Tec

V-Tec DT16D3 Bedienungsanleitung

V-Tec

V-Tec 37TD7-V1 Bedienungsanleitung

V-Tec

V-Tec Livila VT27 Bedienungsanleitung

V-Tec

V-Tec DT596/KP Bedienungsanleitung

V-Tec

V-Tec VT596/KP Bedienungsanleitung

V-Tec

V-Tec DT-DJ5A Bedienungsanleitung

V-Tec

V-Tec DMR11 Bedienungsanleitung

V-Tec

V-Tec 2Easy DMR18s Bedienungsanleitung

V-Tec

V-Tec DMR18S Bedienungsanleitung

V-Tec

V-Tec VIDEO DOOR PHONE SYSTEM Bedienungsanleitung

V-Tec

V-Tec DJ4A Bedienungsanleitung

V-Tec

V-Tec DT31M Bedienungsanleitung

V-Tec

V-Tec DMR11 Series Bedienungsanleitung

V-Tec

V-Tec AT27TD7 Bedienungsanleitung

V-Tec

V-Tec AT16/C5 Bedienungsanleitung

V-Tec

V-Tec 2-WIRE Bedienungsanleitung

V-Tec

V-Tec DT591 Bedienungsanleitung

V-Tec

V-Tec C5-AT25/D4 Bedienungsanleitung

V-Tec

V-Tec DT-DJ4A Bedienungsanleitung

V-Tec

V-Tec DT-DJ4S Bedienungsanleitung

V-Tec

V-Tec dt-dj5a Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung