V-tech Bs2652 Bedienungsanleitung

When using your telephone equipment, basic safety precautions should always be

followed to reduce the risk of fire, electric shock and injury to persons, including the

following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen sink,

or swimming pool).

5. Do not place this product on an unstable cart, stand, or table. The product may

fall, causing serious damage.

6. Slots and openings in the Handset and Base Unit are provided for ventilation.

To protect it from overheating, these openings must not be blocked by placing

the product on a bed, sofa, rug, or other similar surface. This product should

never be placed near or over a radiator or heat register. This product should

not be placed in a built-in installation where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated

on the marking label. If you are not sure of the type of power supply to your

home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not install this product where

the cord might be damaged by anyone walking on it.

9. Never push objects of any kind into this product through holes and slots in the

Handset and Base Unit as they may touch dangerous voltage points or short

out parts that could result in a risk of fire or electric shock. Never spill liquid

of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product, but take

it to an authorized service facility. Opening or removing cabinet parts other than

specified access doors may expose you to dangerous voltages or other risks.

Incorrect reassembling can cause electric shock when the appliance is

subsequently used.

11. Do not overload wall outlets and extension cords as this can result in the risk

of fire or electric shock.

Important Safety Instructions

12. Unplug this product from the wall outlet and refer servicing to an authorized service

facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions, because improper adjustment of other controls may result in

damage and will often require extensive work by an authorized technician

to restore the product to normal operation.

E. If the product has been dropped and the cabinet has been damaged.

F. If the product exhibits a distinct change in performance.

13. Avoid using a telephone (other than a cordless type) during an electrical storm.

There may be a remote risk of electric shock from lightning.

14. Do not use the telephone to report a gas leak in the vicinity of the leak.

SAVE THESE INSTRUCTIONS

Important Safety Instructions

The 2652 is an advanced cordless telephone that operates in the 2.4 GHz frequency

range. Your 2652 is capable of supporting up to a maximum of 4 Handsets. Using

additional Handsets, up to three people can be conferenced on a call (2 Handsets

and the Base Speakerphone), or two extensions can be conferenced on a call, while

two other extensions can be talking internally, using the Intercom feature.

This manual is designed to familiarize you with the 2652 cordless telephone.

Introduction

IMPORTANT

Please record the Base ID code (BS ID) printed on the underside of the

2652 Base in the space below. Please be certain to include all 15 digits/

characters.

Base ID#

Parts Check List

5. Battery Pack

6. Belt Clip

7. User's Manual

1. Base Unit

2. Handset

3. AC Power Adapter

4. Telephone Cord

Handset

Base Unit

Battery Pack Belt Clip

Telephone Cord

AC Power Adapter

The Handset Layout

1. Antenna

2. Message Waiting Indicator

3. Earpiece

4. Headset Jack (2.5mm)

5. Scroll Keys

6. On/Flash

7. Dialing Key (0 - 9, *, #)

8. Handsfree Speakerphone

9. LCD Display

10. Select

11. Off/Clear

12. Intercom

13. Billed Services

14. Microphone

The Base Unit Layout

Page Key

Charge Indicator

Power Indicator

In Use Indicator

Erase Key

Skip Key

Redial Key

Flash Key

Hold Key

Mute Key

Play Key

Volume Keys

Dialing Keys (0 - , *, #)

Speaker Key

Auto Callback Key

3-Way Calling Key

Repeat Dialing Key

Voicemail Key

Charging Contacts

Phone Cord Jack

AC Power Jack

COMPLIES WTH 47 CFR PART 68

REGISTRATION NO.: EW7 CHN-34723-WI-E

RINGER EQUIVALENCE: 0.0B

USOC JACK: RJ11C/RJ11W

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MA

NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST

ACCEPT AN INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MA CAUSE UNDESIRED OPERATION.

PRIVAC OF COMMUNICATIONS MA NOT BE ENSURED WHEN USING

THIS PHONE.

FCC ID: EW780-5001-00

HAC

MODEL : 2652

MANUFACTURED IN CHINA

To AC outlet

To telephone

jack

To telephone

socket outlet

To AC power

jack

COMPLIES WTH 47 CFR PART 68

REGISTRATION NO.: EW7 CHN-34723-WI-E

RINGER EQUIVALENCE: 0.0B

USOC JACK: RJ11C/RJ11W

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MA

NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST

ACCEPT AN INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MA CAUSE UNDESIRED OPERATION.

PRIVAC OF COMMUNICATIONS MA NOT BE ENSURED WHEN USING

THIS PHONE.

FCC ID: EW780-5001-00

HAC

MODEL : 2652

MANUFACTURED IN CHINA

Setup

Plug the AC power adapter into an electrical outlet, and the DC connector into the

back of the Base Unit.

Connecting to phone line

Plug one end of the telephone line cord into the jack on the back of the Base Unit.

Plug the other end of this cord into the wall jack.

Checking for dial tone

After the battery is charged press ON on the Handset. The Phone icon will appear

on the Handset display, and you will hear dial tone. If not, see In Case of Difficulty.

Tone/Pulse selection

See BASE SETTINGS for details.

CAUTION: Use only the power supply provided with your 2652 Unit.

IMPORTANT:

For best performance the 2652

should be installed as follows:

In an elevated location, in the

center of the room, with no

obstructions nearby.

In a location that is away from

other electrical appliances such as

microwave ovens, personal

computers, or televisions.

Getting Started

Follow the steps below:

1. Remove battery compartment cover

by pressing on the indent and

sliding downward.

2. Place the new battery pack in the

Handset with the metal contacts

aligned with the charge contacts in

the battery compartment.

3. Replace the battery compartment

cover by sliding it upwards.

4. If the new battery pack is not

already charged, place the Handset

in the Base Unit, or a charging

stand, and allow it to charge for 10-

12 hours. After initial charge, a

maintenance charge of 8 hours

should be sufficient.

Installation of Battery Pack in Handset

The original Handset that is shipped with your 2652 system will be automatically

registered to the Base. This Handset is HANDSET 1.

As you register additional Handsets to the system, they will be assigned extension

numbers in the following order: HANDSET 2, HANDSET 3 and HANDSET 4.

Whenever a Handset battery pack is installed, the Handset will automatically begin

SEARCHING FOR BASE (if previously registered), or it will prompt you to ENTER BASE

ID to register the new Handset.

Getting Started

Spare Battery Charger/Power Backup Function

CAUTION: TO

REDUCE RISK OF FIRE,

USE ONLY VTECH

80-5017-00-00

CAUTION: TO

REDUCE RISK OF FIRE,

USE ONLY VTECH

80-5017-00-00

BATTERY

INSTALL

THIS

SIDE UP

CAUTION: TO

REDUCE RISK OF FIRE,

USE ONLY VTECH

80-5017-00-00

CAUTION: TO

REDUCE RISK OF FIRE,

USE ONLY VTECH

80-5017-00-00

BATTERY

INSTALL

THIS

SIDE UP

COMPLIES WTH 47 CFR PART 68

REGISTRATION NO.: EW7 CHN-34723-WI-E

RINGER EQUIVALENCE: 0.0B

USOC JACK: RJ11C/RJ11W

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MA

NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST

ACCEPT AN INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MA CAUSE UNDESIRED OPERATION.

PRIVAC OF COMMUNICATIONS MA NOT BE ENSURED WHEN USING

THIS PHONE.

FCC ID: EW780-5001-00

HAC

MODEL : 2652

MANUFACTURED IN CHINA

1. Open the spare battery charger by

pressing the release button, located

on the right-hand side of the Base

Unit. A drawer will open to reveal the

spare battery compartment.

2. Place a battery pack in the drawer

with the charge contacts facing up

and to the left.

3. Push the drawer closed.

The spare battery takes 24 hours to

fully charge a drained battery.

Getting Started

The 2652 can use the spare battery in the Base Unit to provide operational

backup in the event of a power failure. With a fully charged battery pack in

the spare battery charger, you will still be able to place and receive calls from

the Handset for up to 3 hours.

The spare battery pack can also be used to replace a drained Handset battery,

ensuring uninterrupted use.

A spare battery can be purchased from most retail stores that carry

electronic equipment.

NOTE :

When using the 2652 during Power Backup mode, audio quality may be

compromised due to reduced Power availability. The Base Unit can't be used

when power backup mode.

Getting Started

ChargingOfHandsetBatteryPack

The Handset of your 2652 cordless telephone is powered by a rechargeable battery

pack. It charges automatically whenever the Handset is in the Base Unit.

You should charge the battery pack for 12 hours when you first receive your

phone. You'll know the battery pack needs charging when:

CAUTION: to reduce the risk of fire or injury to persons by battery, read

and follow these instructions.

1. Use only the appropriate type and size battery pack specified in the instruction

manual provided for this product.

2. Do not dispose of the battery pack in a fire. The cell may explode. Check with

State and local codes for possible special disposal instructions.

3. Do not open or mutilate the battery pack. Released electrolyte is corrosive and

may cause damage to the eyes or skin. It may be toxic if swallowed.

4. Exercise care in handling battery in order not to short the battery with conducting

materials such as rings, bracelets, and keys. The battery or conductor may overheat

and cause burns.

5. Charge the battery pack provided with or identified for use with this product only

in accordance with the instructions and limitations specified in the instruction manual.

6. Observe proper polarity orientation between the battery pack and battery charger.

• The low battery message is

displayed:

• The Handset seems completely

dead, the LCD is completely clear

and does not activate when you

press the keys.

Andere Handbücher für bs2652

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere V-tech Schnurloses Telefon Handbücher

V-tech

V-tech MI6807 Bedienungsanleitung

V-tech

V-tech MI6821 - Cordless Telephone With Caller Id Benutzerhandbuch

V-tech

V-tech CS6529-14 Bedienungsanleitung

V-tech

V-tech vt9241 Bedienungsanleitung

V-tech

V-tech Cordless Telephone Bedienungsanleitung

V-tech

V-tech CS6124 Bedienungsanleitung

V-tech

V-tech i6767 - 5.8 Digital GHz Two Handset Cordless Phone... Einrichtungshandbuch

V-tech

V-tech DS6151 - 6.0 Expandable Cordless Phone Bedienungsanleitung

V-tech

V-tech CS1200-B Bedienungsanleitung

V-tech

V-tech ip5850 Bedienungsanleitung

V-tech

V-tech 2431 - VT Cordless Phone Bedienungsanleitung

V-tech

V-tech DECT 6.0 LS6315 Series Bedienungsanleitung

V-tech

V-tech i 5871 Bedienungsanleitung

V-tech

V-tech ia5865 Bedienungsanleitung

V-tech

V-tech LS6205 - Cordless Extension Handset Bedienungsanleitung

V-tech

V-tech Cordless Phone with Digital Answering System and Caller... Bedienungsanleitung

V-tech

V-tech 6031 Bedienungsanleitung

V-tech

V-tech VT5875 Bedienungsanleitung

V-tech

V-tech T2351 Benutzerhandbuch

V-tech

V-tech DS6673-6C Bedienungsanleitung

V-tech

V-tech Three Handset Connect to CELL™ Answering System with Caller... Bedienungsanleitung

V-tech

V-tech 9117 Bedienungsanleitung

V-tech

V-tech CS6919 Bedienungsanleitung

V-tech

V-tech gz 2334 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Furuno

Furuno FM-4721 Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

V-tech bs2652 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken