V-tech Vt2463 Bedienungsanleitung

When using your telephone equipment, basic safety precautions should

always be followed to reduce the risk of fire, electric shock and injury

to persons, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub,

kitchen sink, or swimming pool).

5. Do not place this product on an unstable cart, stand, or table. The

product may fall, causing serious damage to the product.

6. Slotsandopeningsinthecabinetandthebackorbottomareprovided

for ventilation. To protect it from overheating, these openings must

not be blocked by placing the product on the bed, sofa, rug, or other

similar surface. This product should never be placed near or over

a radiator or heat register. This product should not be placed in a

built-in installation where proper ventilation is not provided.

7. This product should be operated only from the type of power source

indicated on the marking label. If you are not sure of the type of

power supply to your home, consult your dealer or local power

company.

8. Do not allow anything to rest on the power cord. Do not locate this

product where the cord will be abused by persons walking on it.

9. Never push objects of any kind into this product through cabinet slots

as they may touch dangerous voltage points or short out parts that

could result in a risk of fire or electric shock. Never spill liquid of any

kind on the product.

10. Toreducetheriskofelectricshock,donotdisassemblethisproduct,

but take it to an authorized service facility. Opening or removing

cabinet parts other than specified access doors may expose you

to dangerous voltages or other risks. Incorrect reassemb-ling can

cause electric shock when the appliance is subsequently used.

11. Do not overload wall outlets and extension cords as this can result

in the risk of fire or electric shock.

IMPORTANT SAFETY INSTRUCTIONS

12. Unplug this product from the wall outlet and refer servicing to an

authorized service facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. Iftheproductdoesnotoperatenormallybyfollowingtheoperating

instructions. Adjust only those controls that are covered by the

operating instructions, because improper adjustment of other

controls may result in damage and will often require extensive

workbyanauthorizedtechniciantorestoretheproducttonormal

operation.

E. If the product has been dropped and the cabinet has been

damaged.

F. If the product exhibits a distinct change in performance.

13. Avoidusingatelephone(otherthanacordlesstype)duringanelectrical

storm. There may be a remote risk of electric shock from lighting.

14. Do not use the telephone to report a gas leak in the vicinity of the

leak.

SAVE THESE INSTRUCTIONS

Enhanced 2.4GHzTechnology -

DualBand

transmissioncombinesthebestof2.4GHz

and 900MHz technologies, providing enhanced performance over standard cordless

telephones.

About Caller Identification (Caller ID)

This product has a Caller ID with Call Waiting feature that works with

service from your local phone service provider.

Caller ID with CallWaiting lets you see who’s calling before you answer the phone, even

when you’re on another call.

You may need to change your phone service to use this feature. Contact your phone

service provider if:

• You have both Caller ID and Call Waiting, but as separate services

(you may need combined service)

• You have only Caller ID service, or only Call Waiting service.

• You don’t subscribe to any Caller ID or Call Waiting services.

You can use this product with regular Caller ID service, and you can use this product’s

other features without subscribing to either Caller ID or combined Caller ID with Call

Waiting service.

There are fees for Caller ID services, and they may not be available in all areas.

This product can provide information only if both you and the caller are in areas offering

BEFORE YOU BEGIN

Caller ID service, and if both telephone companies use compatible equipment.

Parts Check List:

1. Base Unit

3. AC Power Adapter

5. Battery Pack

2.Handset

4.Telephone Line Cond

6.Owner’s Manual

To purchase replacement battery packs, call 1-800-595-9511

Handset Base Unit T

AC Power Adaptor

Battery Pack

Owners Manual

INSTALLATION

BeforeYou Install

1 Choose a location for the Base near an electrical outlet and a telephone

jack.

This phone requires a modular telephone jack and a standard electrical

outlet (110v AC) not controlled by a wall switch.Plug the AC power adaptor

into the electrical outlet and the DC connector to the jack on the bottom of the

Base Unit.

2 Install the handset battery.

Use only battery pack provided or recommended by the manufacturer.

NOTE:

Install the base unit and spare handset charger away from electronic

equipment such as personal computers, television sets or microwave ovens.

Avoid excessive heat, cold, dust or moisture.

a) Remove battery

compartment cover by

pressing on the indenlation

and sliding downward.

b) Align the two holes in the plug

with the socket pins, then snap

the plug into place.

c) Place battery pack in the

compartment with the wires

in the lower left corner. Run

the wires under the guide

located directly below the

battery pack.

d) Replace cover by sliding

it up into place.

INSTALLATION

3. Charge the handset battery.

Place the handset in the base. Charge the battery for at least 12 hours the first time.

4. Check for dial tone

After the batteries are charged, connect the modular telephone cord between a live

phone jack and the jack located on the bottom of the Base Unit. Pick up the Handset

and press PHONE. You should hear a dial tone.

5. Set the dial mode.

If you have touch tone service, the phone is ready to use as soon as the batteries are charged.

If you have dial pulse (rotary) service, you’ll need to change the dial mode.

• Press PROG/CHANNEL on the handset to enter programming mode.

• Press or until the screen displays DIAL MODE:and the currently selected mode.

• Press SELECT.The current setting blinks.

• Press to select PULSE (or TONE).

• Press SELECT to save the displayed mode.

Table/Desk Installation

Connect the power cord

Connect the telephone

line cord

MODEL: 2463

DC 9V 500mA

CLASS 2 POWER SOURCE ONLY

Michael Graves

MANUFACTURED IN CHINA

CORDLESS TELEPHONE

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE;AND

2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN

USING THIS PHONE.

PRODUCT CONTAINS NICKEL-CADMIUM

BATTERY: MUST BE RECYCLED OR DISPOSED

OF PROPERLY. DO NOT BURN OR PUNCTURE

BATTERY. LIKE OTHER BATTERIES OF THIS

TYPE. IF IT IS BURNED OR PUNCTURED. IT

COULD RELEASE TOXIC MATERIAL WHICH

COULD CAUSE INJURY.

POWER JACK

COMPLIES WITH 47 CFR PART 68

REGISTRATION NO.: US: EW7W901B24280

RINGER EQUIVALENCE: 0.1B

USOC JACK: RJ11C/RJ11W

HAC

FCC ID: EW780-5125-B01

9V DC

TELEPHONE OPERATION

Answer a Call

Press any key

except OFF

HOLD

Press to put a call on hold;

press HOLD again to return

to the call,OR lift the Handset

of an extension phone.

Make a Call

Press TALK / FLASH,

then dial the number

OR Dial the number

(use to backspace

and correct digits),then

press TALK / FLASH

Press TALK/FLASH to

answer call waiting.

Handset Volume

While on a call,

adjust the volume

of what you hear

End a Call

Press OFF or place

Handset in Base

cradle

Exit

programming

Cancel a page

Redial

Press PHONE,

then press

REDIAL / PAUSE

to call last number

dialed(up to

32 digits)

Program/Channel

Switch to a clearer

channel while on a call

Enter programming

mode with Handset

idle(on hook)

Memory

Use MEM to program

and dial stored numbers.

SELECT

Use SELECT in

conjunction with

PROG/CHAN during

Handset programming

TELEPHONE OPERATION

Page / Handset Locator

Press to page the Handset for

up to 60 seconds. Press again to

cancel,or press OFF on Handset.

IN USE / CHARGE Indicator

Flashes when the Handset is in use,

and glows when the Handset is charging.

This indicator will also flash rapidly while

a call is on HOLD.

ON / OFF Indicator

This indicator glows

when the Answering

System is ON.

Handset Ringer Style/Battery Save

You can select from four different handset ringer styles, or turn the ringer off and

extend the battery life.

1Make sure the handset is off.

2Press

PROG/CHANNEL

to enter programming mode.

3Press until the screen displays RINGER:, and the current selection.

4Press

SELECT

.The screen displays the current setting.

5Press or to select 1, 2, 3, 4, or OFF.You will hear a sample of each

ring.

6Press

SELECT

to choose the displayed ringer setting.

TemporaryTone Dialing

If you have dial pulse (rotary) service, you can change from dial pulse to touch

tone dialing during a call by pressing

TONE.This is useful if you need to send

touch tone signals for access to telephone banking or long-distance services.

1Dial the number.

2Press

TONE. Buttons pressed after this send touch tone signals.

3After you hang up, the phone automatically returns to dial pulse (rotary)

service.

1Make sure the handset is off.

2 Press

PROG/CHANNEL

to enter programming mode.

3Press until the screen displays DATE/TIME.

4. Press

SELECT.

The MONTH is flashing. Use and to select the current

month. Press

SELECT;

The DAY is flashing. Use and to select the correct day. Press

SELECT;

The HOUR is flashing. Use and to select the current hour. Press

SELECT;

The MINUTE is flashing. Use and to select the correct minute. Press

SELECT;

AM or PM is flashing. Use or to choose between AM and PM. Press

SELECT,

DATE /TIME programming is complete.

Note:

The Date / Time will be updated automatically when there is incoming

TELEPHONE OPERATION

Setting Date /Time

Caller ID data.

TELEPHONE OPERATION

Display Screen Messages

Operating Range

This cordless telephone operates within the maximum power allowed by

the Federal Communications Commission (FCC). Even so, this handset and

base can communicate over only a certain distance — which can vary with the

locations of the base and handset, the weather, and the construction of your

home or office. For best performance, keep the base antenna fully upright.

If you receive a call while you are out of range, the handset might not

ring — or if it does ring, the call might not connect when you press

TALK

Move closer to the base, then press

TALK

to answer the call.

If you move out of range during a phone conversation, you might

hear noise or interference.To improve reception, move closer to the base.

If you move out of range without pressing

OFF

,your phone will be left

“off the hook.” To hang up properly, walk back into range, periodically

pressing

OFF

Screen Displays: When:

NO LINE

RINGING

CONNECTING...

PHONE ON

MESSAGES WAITING

**PAGING**

HOLD

EXTENSION IN USE

BATTERY LOW

The base is not connected to the telephone line,

or the line is not working.

There is a call coming in.

The handset is waiting for dial tone.

The handset is in use.

You have received telephone company voice mail.

There is a call on hold.

Another extension on this line is off hook.

The battery needs to be recharged.

The base is paging the handset.

Inhaltsverzeichnis

Andere V-tech Schnurloses Telefon Handbücher

V-tech

V-tech T2455 - 2.4GHz Dual Handset Cordless Phone... Bedienungsanleitung

V-tech

V-tech LS6117-18 Bedienungsanleitung

V-tech

V-tech IS6100 Bedienungsanleitung

V-tech

V-tech VTECH LS6426-3 Bedienungsanleitung

V-tech

V-tech ES1210 Bedienungsanleitung

V-tech

V-tech DS5151-2 Bedienungsanleitung

V-tech

V-tech DS4121-3 Bedienungsanleitung

V-tech

V-tech CS6199-4 Bedienungsanleitung

V-tech

V-tech IA5854 Benutzerhandbuch

V-tech

V-tech CS6124 Bedienungsanleitung

V-tech

V-tech Analog Contemporary Series Bedienungsanleitung

V-tech

V-tech 2151 Bedienungsanleitung

V-tech

V-tech Cordless Telephone Bedienungsanleitung

V-tech

V-tech DS3111-2 - DECT 6.0 Cordless Phone Bedienungsanleitung

V-tech

V-tech t2447 Bedienungsanleitung

V-tech

V-tech DS3101 Bedienungsanleitung

V-tech

V-tech T2440 - 2.4GHz Dual Handset Cordless System Bedienungsanleitung

V-tech

V-tech CS6114 Bedienungsanleitung

V-tech

V-tech gz2336 Benutzerhandbuch

V-tech

V-tech LS1650-B Bedienungsanleitung

V-tech

V-tech vt9127 Bedienungsanleitung

V-tech

V-tech t2350 Benutzerhandbuch

V-tech

V-tech 9119 Bedienungsanleitung

V-tech

V-tech t2429 - 2.4 GHz Analog Cordless Phone Benutzerhandbuch

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Furuno

Furuno FM-4721 Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

V-tech vt2463 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken