V-tech vt2468 Bedienungsanleitung
1
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub,
kitchen sink, or swimming pool).
5. Do not place this product on an unstable cart, stand, or table. The
product may fall, causing serious damage to the product.
6. Slotsandopeningsinthecabinetandthebackorbottomareprovided
for ventilation. To protect it from overheating, these openings must
not be blocked by placing the product on the bed, sofa, rug, or other
similar surface. This product should never be placed near or over a
radiatororheatregister. Thisproductshouldnotbeplacedinabuilt-
in installation where proper ventilation is not provided.
7. This product should be operated only from the type of power source
indicatedonthemarkinglabel.Ifyouarenotsureofthetypeofpower
supply to your home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this
product where the cord will be abused by persons walking on it.
9. Never push objects of any kind into this product through cabinet slots
astheymaytouchdangerousvoltagepointsorshortoutpartsthatcould
result in a risk of fire or electric shock. Never spill liquid of any kind
on the product.
10. Toreducetheriskofelectricshock,donotdisassemblethisproduct,
but take it to an authorized service facility. Opening or removing
cabinet parts other than specified access doors may expose you
to dangerous voltages or other risks. Incorrect reassemb-ling can
cause electric shock when the appliance is subsequently used.
11. Do not overload wall outlets and extension cords as this can result
in the risk of fire or electric shock.
IMPORTANT SAFETY INSTRUCTIONS
2
12. Unplug this product from the wall outlet and refer servicing to an
authorized service facility under the following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. Iftheproductdoesnotoperatenormallybyfollowingtheoperating
instructions. Adjust only those controls that are covered by the
operating instructions, because improper adjustment of other
controls may result in damage and will often require extensive
workbyanauthorizedtechniciantorestoretheproducttonormal
operation.
E. If the product has been dropped and the cabinet has been
damaged.
F. If the product exhibits a distinct change in performance.
13. Avoidusingatelephone(otherthanacordlesstype)duringanelectrical
storm. There may be a remote risk of electric shock from lighting.
14. Do not use the telephone to report a gas leak in the vicinity of the
leak.
VTECH COMMUNICATIONS INC
SERVICEDEPT.at 1-800-595-9511.InCanada, callVTechElectronics Ltd
at1-800-267-7377.
SAVE THESE INSTRUCTIONS
3
About Caller Identification (Caller ID)
This product has a Caller ID with Call Waiting feature that works with
servicefrom yourlocalphone service provider.
Caller ID with Call Waiting lets you see who’s calling before you answer
thephone, even whenyou’re onanother call.
You may need to change your phone service to use this feature.Contact
yourphoneservice providerif:
• You have both Caller ID and CallWaiting, but as separate services
(you may need combined service)
• You have only Caller ID service, or only CallWaiting service.
• You don’t subscribe to any Caller ID or Call Waiting services.
You canuse this productwith regular CallerID service,and you canuse this
product’s other features without subscribing to either Caller ID or combined
CallerIDwithCallWaitingservice.
There are fees for Caller ID services, and they may not be available in all
areas.
Thisproductcanprovideinformationonlyifbothyouandthecallerareinareas
offeringCallerID service,andif bothtelephonecompaniesuse compatible
equipment.
BEFORE YOU BEGIN
4
Before You Install
1 Choose a location for the base near an electrical outlet and a
telephonejack.
Thisphonerequires amodulartelephone jackanda standardelectrical
outlet (110v AC) not controlled by a wall switch.
2 Install the handset battery.
Use onlyVTECH battery.
a) Removebattery
compartment
coverbypressing
onthe
indentation
andsliding
downward.
c) Place battery pack
incompartment
with the wires in
thelower left
corner,along the
bottomof the
battery pack.
b) Align two holes in
plug with socket
pins, and snap the
plug into place.
d) Replace
coverby
sliding it up
into place.
INSTALLATION
5
3 Attach belt clip to the cordless handset (optional).
INSTALLATION
2 Connectthe
power cord.
NOTE: Install the base unit and spare handset charger away from elec-
tronic equipment such as personal computers, television sets or micro-
wave ovens. Avoid excessive heat, cold, dust or moisture.
Table/Desk Instration
To attach
Standard
electrical outlet Modular
telephone
jack
1 Connectthe
telephone
line cord.
To remove
6
3 Charge the handset battery.
Place the handset in the base. Charge the battery for at least 12
hours the first time.
4 Check for dial tone.
After the batteries are charged, pick up the handset and press
PHONE
;you should hear a dial tone.
5 Set the dial mode.
If you have touch tone service, the phone is ready to use as soon as
thebatteries are charged.
Ifyouhavedialpulse(rotary)service,you’llneedtochangethedialmode.
• Press
PROG/CHAN
on the handset to enter programming mode.
• Press or until the screen displays DIAL MODE: and the
currentlyselected mode.
• Press
SELECT
.The current setting blinks.
• Press to select TONE or PULSE.
• Press
SELECT
, to save the displayed mode.
INSTALLATION
7
a) Align holes on
basewith
mountingstuds
on wall jack.
b) Pullbasedown
onmounting
studs until it
locks into place.
4 Follow Steps 3–5 in Table/Desk Installation.
Wall Installation
1 Connect the telephone line cord.
2 Connect the power cord.
3 Mount the base on the wall.
Modular
telephone jack
Standard
electrical outlet
INSTALLATION
8
End a Call
Press
OFF
—
OR
—
Placehandset
in base.
Exit
programming.
Cancela page.
TELEPHONE OPERATION
Handset Volume
While on a call,
adjustvolume
of what you hear.
Hold
Press to put a
call on hold.
Press again to
releasehold
—
OR
—
Liftthe handset
ofan extension.
Answer a Call
Press any key
except
OFF
.
Change Channel
Switch to a clearer channel
while on a call.
Redial
Press
PHONE
, then
press
REDIAL/PAUSE
to call last number
dialed (up to 32 digits).
Make a Call
Press
PHONE
, then
dialthenumber
—
OR
—
Dialthe number(use
to backspace and
correct digits), then
press
PHONE
to call.
Flash/
Call Waiting
Access special
telephonecompany
subscriberservices.
Enterprogramming while noton a call.
9
Page/Handset Locator
Press to page the handset for up to
60 seconds. Press again to cancel,
or press
OFF
on handset.
TELEPHONE OPERATION
Flashing:
handset is in use
Onsteadily:
handset is
chargingin
base
Flashes
whenyouhave
unreviewed
callinformation.
10
Handset Ringer Style/Battery Save
Youcanselect fromfour differenthandsetringerstyles,orturntheringeroff
and extend the battery life.
1Make sure the handset is off.
2Press
PROG/CHAN
to enter programming mode.
3Press until the screen displays RINGER:.
4Press
SELECT
.The screen displays the current setting.
5Press or to select 1, 2, 3, 4, or OFF.You will hear a sample
ofeachring.
6Press
SELECT
to choose the displayed ringer setting.
Temporary Tone Dialing
If you have dial pulse (rotary) service, you can change from dial pulse to
touch tone dialing during a call by pressing
*
. This is useful if you need to
send touch tone signals for access to telephone banking or long-distance
services.
1Dialthenumber.
2Press
*
. Buttons pressed after this send touch tone signals.
3After you hang up, the phone automatically returns to
dialpulse(rotary) service.
Headset Jack
You canuse thistelephonehands-free when
you install any VTech 2.5 mm headset,
purchasedseparately.
Plug the headset into the jack located
on the right side of the handset
(underthesmall rubberflap).
Donot forcethe connection,
but make sure the plug
fits securely.
TELEPHONE OPERATION
Inhaltsverzeichnis
Andere V-tech Schnurloses Telefon Handbücher
V-tech
V-tech DS6301 - Dect 6.0 Cordless Phone Bedienungsanleitung
V-tech
V-tech Cordless Telephone Bedienungsanleitung
V-tech
V-tech CS6199-4 Bedienungsanleitung
V-tech
V-tech DS3101 Bedienungsanleitung
V-tech
V-tech gz2339 Benutzerhandbuch
V-tech
V-tech USB 7200 Bedienungsanleitung
V-tech
V-tech CS6919 Bedienungsanleitung
V-tech
V-tech DS6621-2 Bedienungsanleitung
V-tech
V-tech DS8141 Bedienungsanleitung
V-tech
V-tech ia5829 - Cordless Phone - Operation Bedienungsanleitung
V-tech
V-tech DS6122-5 Bedienungsanleitung
V-tech
V-tech Cordless Telephone Bedienungsanleitung
V-tech
V-tech i6789 Bedienungsanleitung
V-tech
V-tech TD45270194 - DECT 6.0 With 2 Handsets Bedienungsanleitung
V-tech
V-tech TeleZapper VT2558 Bedienungsanleitung
V-tech
V-tech DS6673-2 Bedienungsanleitung
V-tech
V-tech ia5870 Bedienungsanleitung
V-tech
V-tech LS6245 Bedienungsanleitung
V-tech
V-tech CS5119 Bedienungsanleitung
V-tech
V-tech i 5867 Bedienungsanleitung
