V-tech Vz2652 Bedienungsanleitung

When using your telephone equipment, basic safety precautions should always

befollowedtoreducetheriskoffire,electricshockandinjurytopersons,including

the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid

or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen

sink, or swimming pool).

5. Do not place this product on an unstable cart, stand, or table. The product

may fall, causing serious damage.

6. Slots and openings in the Handset and Base Unit are provided for

ventilation. To protect it from overheating, these openings must not be

blocked by placing the product on a bed, sofa, rug, or other similar

surface. This product should never be placed near or over a radiator

or heat register. This product should not be placed in a built-in installation

where proper ventilation is not provided.

7. This product should be operated only from the type of power source

indicated on the marking label. If you are not sure of the type of power

supply to your home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not install this product

where the cord might be damaged by anyone walking on it.

9. Never push objects of any kind into this product through holes and slots

in the Handset and Base Unit as they may touch dangerous voltage points

or short out parts that could result in a risk of fire or electric shock. Never

spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product,

but take it to an authorized service facility. Opening or removing cabinet

parts other than specified access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling can cause electric shock

when the appliance is subsequently used.

11. Do not overload wall outlets and extension cords as this can result in

the risk of fire or electric shock.

Important Safety Instructions

12. Unplug this product from the wall outlet and refer servicing to an

authorized service facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the

operating instructions, because improper adjustment of other controls

may result in damage and will often require extensive work by an

authorized technician to restore the product to normal operation.

E. If the product has been dropped and the cabinet has been damaged.

F. If the product exhibits a distinct change in performance.

13. Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning.

14. Do not use the telephone to report a gas leak in the vicinity of the leak.

SAVETHESE INSTRUCTIONS

Important Safety Instructions

The 2652 is an advanced cordless telephone that operates in the 2.4 GHz

frequency range.

This manual is designed to familiarize you with the 2652 cordless telephone.

Introduction

IMPORTANT

Please record the Base ID code (BS ID) printed on the underside of the

2652 Base in the space below. Please be certain to include all 15 digits/

characters.

Base ID#

5. Battery Pack

6. Belt Clip

7. User's Manual

1. Base Unit

2. Handset

3. AC Power Adapter

4. Telephone Cord

Handset

Base Unit

Battery Pack Belt Clip

Telephone Cord

AC Power Adapter

Parts Check List

The Handset Layout

1. Antenna

2. Message Waiting Indicator

3. Earpiece

4. Headset Jack (2.5mm)

5. Scroll Keys

6. On/Flash

7. Dialing Key (0 - 9, *, #)

8. HandsfreeSpeakerphone

9. LCD Display

10. Select

11. Off/Clear

12. Intercom

13. Billed Services

14. Microphone

The Base Unit Layout

Page Key

Charge Indicator

Power Indicator

In Use Indicator

Erase Key

Skip Key

Redial Key

Flash Key

Hold Key

Mute Key

Play Key

Volume Keys

Dialing Keys (0 - , *, #)

Speaker Key

Auto Callback Key

3-Way Calling Key

Repeat Dialling Key

Voicemail Key

Charging Contacts

Phone Cord Jack

AC Power Jack

COMPLIES WTH 47 CFR PART 68

REGISTRATION NO.: EW7 CHN-34723-WI-E

RINGER EQUIVALENCE: 0.0B

USOC JACK: RJ11C/RJ11W

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MA

NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST

ACCEPT AN INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MA CAUSE UNDESIRED OPERATION.

PRIVAC OF COMMUNICATIONS MA NOT BE ENSURED WHEN USING

THIS PHONE.

FCC ID: EW780-5001-00

HAC

MODEL : 2652

MANUFACTURED IN CHINA

To AC outlet

To telephone

jack

To telephone

socket outlet

To AC power

jack

COMPLIES WTH 47 CFR PART 68

REGISTRATION NO.: EW7 CHN-34723-WI-E

RINGER EQUIVALENCE: 0.0B

USOC JACK: RJ11C/RJ11W

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MA

NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST

ACCEPT AN INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MA CAUSE UNDESIRED OPERATION.

PRIVAC OF COMMUNICATIONS MA NOT BE ENSURED WHEN USING

THIS PHONE.

FCC ID: EW780-5001-00

HAC

MODEL : 2652

MANUFACTURED IN CHINA

Setup

Plug the AC power adapter into an electrical outlet, and the DC connector

into the back of the Base Unit.

Connecting to phone line

Plug one end of the telephone line cord into the jack on the back of the Base

Unit. Plug the other end of this cord into the wall jack.

Checking for dial tone

After the battery is charged press ON on the Handset. The Phone icon

will appear on the Handset display, and you will hear dial tone. If not, see

In Case of Difficulty.

Tone/Pulse selection

See BASE SETTINGS for details.

CAUTION: Use only the power supply provided with your 2652 Unit.

IMPORTANT:

For best performance the 2652

should be installed as follows:

In an elevated location, in the center

of the room, with no obstructions

nearby.

In a location that is away from other

electricalappliancessuchasmicrowave

ovens, personal computers, or

televisions.

Getting Started

Follow the steps below:

1. Remove battery compartment

cover by pressing on the indent

and sliding downward.

2. Place the new battery pack in

the Handset with the metal

contacts aligned with the charge

contacts in the battery

compartment.

3. Replace the battery

compartment cover by sliding it

upwards.

4. If the new battery pack is not

already charged, place the

Handset in the Base Unit, or a

charging stand, and allow it to

charge for 10-12 hours. After

initial charge, a maintenance

charge of 8 hours should be

sufficient.

Installation of Battery Pack in Handset

The original Handset that is shipped with your 2652 system will be

automatically registered to the Base. This Handset is HANDSET 1.

As you register additional Handsets to the system, they will be assigned

extension numbers in the following order: HANDSET 2, HANDSET 3 and

HANDSET4.

Whenever a Handset battery pack is installed, the Handset will automatically

begin SEARCHING FOR BASE (if previously registered), or it will prompt you

to ENTER BASE ID to register the new Handset.

Getting Started

Spare Battery Charger/Power Backup Function

CAUTION: TO

REDUCE RISK OF FIRE,

USE ON Y VTECH

80-5017-00-00

CAUTION: TO

REDUCE RISK OF FIRE,

USE ON Y VTECH

80-5017-00-00

BATTERY

INSTA

THIS

SIDE UP

CAUTION: TO

REDUCE RISK OF FIRE,

USE ON Y VTECH

80-5017-00-00

CAUTION: TO

REDUCE RISK OF FIRE,

USE ON Y VTECH

80-5017-00-00

BATTERY

INSTA

THIS

SIDE UP

COMPLIES WTH 47 CFR PART 68

REGISTRATION NO.: EW7 CHN-34723-WI-E

RINGER EQUIVALENCE: 0.0B

USOC JACK: RJ11C/RJ11W

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MA

NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST

ACCEPT AN INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MA CAUSE UNDESIRED OPERATION.

PRIVAC OF COMMUNICATIONS MA NOT BE ENSURED WHEN USING

THIS PHONE.

FCC ID: EW780-5001-00

HAC

MODEL : 2652

MANUFACTURED IN CHINA

1. Open the spare battery charger

by pressing the release button,

located on the right-hand side

of the Base Unit. A drawer will

open to reveal the spare battery

compartment.

2. Place a battery pack in the

drawerwiththechargecontacts

facing up and to the left.

3. Push the drawer closed.

The spare battery takes 24 hours to

fully charge a drained battery.

Getting Started

The 2652 can use the spare battery in the Base Unit to provide operational

backup in the event of a power failure. With a fully charged battery pack in

the spare battery charger, you will still be able to place and receive calls from

the Handset for up to 3 hours.

The spare battery pack can also be used to replace a drained Handset battery,

ensuring uninterrupted use.

A spare battery can be purchased from most retail stores that carry

electronic equipment.

NOTE:

When using the 2652 during Power Backup mode, audio quality may be

compromised due to reduced Power availability. The Base Unit can't be used

when in power backup mode.

Getting Started

Charging Of Handset Battery Pack

The Handset of your 2652 cordless telephone is powered by a rechargeable

battery pack. It charges automatically whenever the Handset is in the Base

Unit.

You should charge the battery pack for 12 hours when you first receive

your phone. You'll know the battery pack needs charging when:

CAUTION: to reduce the risk of fire or injury to persons by

battery, read and follow these instructions.

1. Use only the appropriate type and size battery pack specified in the

instruction manual provided for this product.

2. Do not dispose of the battery pack in a fire. The cell may explode. Check

with State and local codes for possible special disposal instructions.

3. Do not open or mutilate the battery pack. Released electrolyte is corrosive

and may cause damage to the eyes or skin. It may be toxic if swallowed.

4. Exercise care in handling battery in order not to short the battery with

conducting materials such as rings, bracelets, and keys. The battery or

conductor may overheat and cause burns.

5. Charge the battery pack provided with or identified for use with this

product only in accordance with the instructions and limitations specified

in theinstruction manual.

6. Observe proper polarity orientation between the battery pack and battery

charger.

• The low battery message is

displayed:

• The Handset seems completely

dead, the LCD is completely

clear and does not activate

when you press the keys.

Andere Handbücher für vz2652

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere V-tech Schnurloses Telefon Handbücher

V-tech

V-tech IP 811 Bedienungsanleitung

V-tech

V-tech CS6124 Bedienungsanleitung

V-tech

V-tech i6775 Bedienungsanleitung

V-tech

V-tech I5808 - Cordless Extension Handset Bedienungsanleitung

V-tech

V-tech t2101 Benutzerhandbuch

V-tech

V-tech gz 2334 Benutzerhandbuch

V-tech

V-tech i 5836 Bedienungsanleitung

V-tech

V-tech i6725 Bedienungsanleitung

V-tech

V-tech DS4121-3 Bedienungsanleitung

V-tech

V-tech LS6217 Bedienungsanleitung

V-tech

V-tech VTECH LS6426-4 Installations- und Betriebshandbuch

V-tech

V-tech vt20-2438 Bedienungsanleitung

V-tech

V-tech CS6859 Bedienungsanleitung

V-tech

V-tech DS6301 - Dect 6.0 Cordless Phone Bedienungsanleitung

V-tech

V-tech ErisBusinessSystem UP407 Bedienungsanleitung

V-tech

V-tech IS8151 Bedienungsanleitung

V-tech

V-tech MI6821 - Cordless Telephone With Caller Id Benutzerhandbuch

V-tech

V-tech VT650 Bedienungsanleitung

V-tech

V-tech CS6114 Bedienungsanleitung

V-tech

V-tech mi6896 - 5.8 GHz DSS Cordless Phone Bedienungsanleitung

V-tech

V-tech DLP73210 Bedienungsanleitung

V-tech

V-tech 6042 Bedienungsanleitung

V-tech

V-tech FS6214 Bedienungsanleitung

V-tech

V-tech DS6472-6 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Furuno

Furuno FM-4721 Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

V-tech vz2652 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken