V-tech i440 Bedienungsanleitung
1
Electronic Emission Notices
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device,pursuanttoPart15ofFCCRules.Theselimitsaredesignedtoprovidereasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with instructions contained in this manual, may cause harmful interference
to radio and television communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- REORIENTORRELOCATETHERECEIVINGANTENNA
- INCREASETHESEPARATIONBETWEENTHEEQUIPMENTANDTHERECEIVER
- CONNECTTHEEQUIPMENTINTOANOUTLETONACIRCUITDIFFERENTFROM
THATOFTHERECEIVER
- CONSULTTHEDEALERORANEXPERIENCEDAUDIO/TELEVISION
TECHNICIAN
NOTE: Connecting this device to peripheral devices that do not comply with Class B
requirements, or using an unshielded peripheral data cable, could also result
in harmful interference to radio or television reception.
The user is cautioned that any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s authority to
operate this equipment.
To ensure that the use of this product does not contribute to interference, it is
necessary to use shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be copied or
reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility for errors
or omissions is assumed. Neither is any liability assumed for damages resulting from the use of the
information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their respective owners.
2
Technical Reference Booklet
Table of Contents
HARDWARE CONFIGURATION.............................................................. 3
Key Features ............................................................................................... 3
Motherboard Layout (Model Code No. - 35893200XX) ............................... 5
Jumper Settings .......................................................................................... 6
CPU Speed Selection............................................................................ 6
JP1 - Host Bus Speed Select ................................................................ 6
JP4 - CMOS Clear.................................................................................. 6
JP28 - Keyboard Power on Password Clear ........................................ 7
JP29 - Keyboard Power Select .............................................................. 7
Keyboard Password Power on.............................................................. 7
JP8, JP23 - BIOS Program Voltage ....................................................... 7
JP20 - On Board PCI Sound Selection.................................................. 7
Pin List of Special Connectors.................................................................... 8
Memory Configuration ................................................................................. 8
To install DIMMs .......................................................................................... 8
Installing the Processor .............................................................................. 9
BIOS SETUP ............................................................................................... 1 0
Starting Setup .............................................................................................. 10
Main Menu ................................................................................................... 10
Standard CMOS Setup ................................................................................ 12
BIOS Features Setup................................................................................... 14
Chipset Features Setup .............................................................................. 14
Power Management Setup.......................................................................... 14
PNP/PCI Configuration Setup ..................................................................... 14
Integrated Peripherals ................................................................................ 14
Supervisor/User Password Setting ............................................................ 14
Flash Update Procedure ............................................................................. 16
3
HARDWARE CONFIGURATION
This motherboard is based on the Intel® 82440BX/ZX/VIA®VT82C693 chipset.
The chipset is a highly integrated solution for a cost-effective and compact
motherboard. The motherboard supports SDRAM, Registered SDRAM. Features
on-board include super-I/O, Ultra DMA33/66(DMA66 only for VT82C596B) PCI
busmasterIDE,AGPVer.1.0,PCIVer2.1compliance,USB,VRM8.4compliance,
ECC (only for 440BX/VIA®VT82C693), Micro ATX specification 1.0 compliance ,
On-board PCI Sound Sub-system (optional).
Key Features
Processor
• Full support for the MendocinoPPGA processors using PGA370 Socket.
• Supports 66MHz and 100MHz bus speed including 300MHz to 533MHz
Mendocino PPGA processor and future PPGA processor.
CPU Speed Jumperless
• Jumper setting or no jumper is needed to set for various speed of CPU
(Factory optional).
VRM (Voltage Regulator Modules) on Board
• Flexible motherboard design with on-board VRM 8.4, easy to upgrade
with Intel’s® Future Overdrive® processors.
Cache
• Processor built-in L2 cache.
System Memory
• A total of two 168-pin DIMM sockets.
• Up to 256MB (SDRAM) or 512MB (Registered SDRAM).
• Supports SDRAM (only for 66MHz Bus speed).
• Supports PC-100, Registered SDRAM (for 100MHz Bus speed).
Memory Organization
Two 168-pin DIMM Socket
• Supportssingle-density DIMMsof 1MB,2MB,4MB, 8MBand 16MBdepth
(x64 or 72).
• Supports double-density DIMMs of 2MB, 4MB, 8MB, 16MB and 32MB
depth (x64 or 72).
• Supports error checking correction (ECC) using parity DRAM modules.
(onlyfor440BX/VIA®VT82C693).
• Banks of different DRAM types depths can be mixed.
Expansion Slots
• 1 AGP slot (ver. 1.0, 1x/2x mode supported).
•3 PCI bus master slots (ver. 2.1 compliant, with 1 PCI slot sharing with
1 ISA slot).
• 1 ISA slot (1 ISA slot sharing with 1 PCI slot).
On-Board I/O
• Two PCI fastIDEportssupporting up to 4 ATA2,Ultra DMA 33/66 (DMA66
only for VT82C596B) IDE HDDs, CD-Roms, ZIP devices and LS-120
Hardware Setup
4
Technical Reference Booklet
drivers as boot drive.
• Supports bus master IDE, PIO mode 4 (up to 16M bytes/sec) and Ultra
DMA33/66 (DMA66onlyforVT82C596B)(upto33/66Mbytes/sec)transfer.
• One ECP/EPP parallel port .
• Two 16550-compatible UART serial ports.
• One floppy port supporting two FDDs of 360KB, 720KB, 1.2MB, 1.44MB
or 2.88MB formated capacity.
• Two USB ports.
• PS/2 keyboard port.
• PS/2 mouse port.
• Infrared (IrDA) support (via a header).
• OneLine/Speakerout,oneMicin,oneLineinandMIDI/Gameport(optional).
System BIOS
• 2MBflashBIOSsupportingPnP,APM,ATAPI,ACPIand DMI.
• Jumper selection for 5V or 12V flash memory voltage.
• Auto detects and supports LBA hard disks with formatted capacities
over8.4GB.
• Easily upgradable by end-user.
Plug-and-Play
• Supports plug-and-play specification 1.1.
• Plug-and-play for DOS, Windows® 3.X, Windows® 95 as well as
Windows® 98.
• Fully steerable PCI interrupts.
Power Management
• SupportsSMM, APMandACPI.
• Break switch for instant suspend/resume on system operation.
• Energy star “Green PC” compliant .
• Supports WAKE-ON-LAN (WOL).
• Supports Wake on Ring for External Modem.
On Board PCI Sound Sub-system (optional)
•Integrated Creative ES1373 PCI Sound Sub-system.
•Including complete audio and play back system.
•64 Voice Wave Table Synthesizer.
•DOS game compatibility.
•PCI bus master for fast DMA.
•Fully Compliant with AC97 Power Management Specification.
Keyboard Password Turn ON
• Special feature for system security.
5
Hardware Setup
Motherboard Layout (Model Code No. - 35893200XX)
Thefollowing diagrams show the relative positions of the jumpers,connectors, major
componentsandmemorybanksonthemotherboard.
Waring:
All connectors on board are labeled Pin “1” at one conner. Ribbon
cables should always be connected with the red stripe on the Pin “1”
side of the connector.
1
1
1
1
1
CN31 CN32
CN17-CPU Fan
JP8
6
Technical Reference Booklet
Jumper Settings
Warning:
Please turn off AC Power before installing and removing any device.
If you can’t turn on system power, please clear CMOS and keyboard
password (JP28). Then try again.
Thischapterexplainshow to configure themotherboard’shardware.Before using your
computer, make sure all jumpers and DRAM modules are set correctly. Refer to this
chapterwhenever indoubt.
CPU Speed Selection
WhenJP7isinstalledonthismotherboard,jumperisrequiredtobesetfordifferenttype
ofCPUinstalled.TheCPUspeedissetbyJP1andJP7,pleaseseeJP7-RatioofProcessor
CoretoSystemBusFrequencytable.
WhenJP7isnotinstalledonthismotherboard,jumperlessfeatureisimplementedsuch
thatnojumper is requiredto be setfordifferent type ofCPU installed.
TheCPUspeedissetin“CPUSpeedSetting”ofCMOSSetup.
Notice:
1. Besureto save theCMOSsettingwhenexittheCMOS.
2. CeleronPGA370CPUisfrequencymultiplierlocked,noCPUspeedchange
willbeseenevenifthefrequencymultipliersettinginCMOSsetupischanged.
JP1 - Host Bus Speed Select
JP1 HCLK
(Close)* Auto*
(Open) 100MHz
JP4 - CMOS Clear
JP4 Selection
(1-2)* Normal*
(2-3) CMOS Clear
Close Open
JP4
JP28
1
1
JP23
JP81
1
* = Default setting.
JP1
1
JP201
1
1
JP291
7
Keyboard Password Power On
This motherboard provides a special security feature of keyboard password
power on. The feature is enabled in Integrated Peripherals Menu of CMOS
setup. There are two modes of operations.
(1) Single Key Turn On - if you set a single key password, the system will
turn on immediately after you press the password key(only for BX/ZX).
(2) Keys Sequence Turn On - if you set a password with more than one
character, ie. a combination of keys, the system will turn on after you
press the password key sequence and then a <enter>.
Please notice that the power button will have no function if the keyboard
passwordpower onfeatureis enabled.
Close Open
* =Default setting
Hardware Setup
JP8, JP23 - BIOS Program Voltage
JP8 JP23 Selection
(1-2) (1-2) INTEL(1MB)
(1-2) (2-3) MX(1MB)
(2-3) (2-3) ATMEL/SST/Winbond(1MB)
(2-3) (2-4) ATMEL/SST/Winbond(2MB)
JP8 & JP23 are pre-installed in the factory. They should NOT be altered by
the users.
JP20 - On Board PCI Sound Selection
JP20 Selection
(1-2)* Enable*
(2-3) Disable
1
1
JP29 - Keyboard Power Select
JP29 Select
(1-2)* Powered by +5V*
(2-3) Powered by +5V Standby
(AllowsKeyboardPassword PowerOn)
1
1
1
1
JP28 - Keyboard Power On Password Clear
JP28 Selection
(1-2)* Normal*
(2-3) Clear Keyboard Power On Password
8
Technical Reference Booklet
Memory Configuration
You caninstallupto 256MB(SDRAM) or512MB(RegisteredSDRAM) of memory
in the motherboard DIMM sockets. The board has DIMM sockets arranged as
banks 1, and 2. You can install DIMMs in any of the two banks, and use different
size DIMMs in different banks. The BIOS detects the size and type of installed
memory.
To install DIMMs
1. Turn off all peripheral devices connected to the computer. Turn off the
computer.
2. Remove the computer cover and locate the DIMM sockets.
3. Holding the DIMM by the edges, remove it from its antistatic package.
4. Make sure the clips at either end of the socket are pushed away from the
socket.
Pin List of Special Connectors:
1 IRRX
2 GND
3 IRTX
4 VCC
4
1
1.CN24: CD-IN(MOLEX) 2.CN25:AUX-IN(MOLEX)
1 CD-L
2 GND
3 GND
4 CD-R
1
4
1
4
1 AUX-L
2 GND
3 GND
4 AUX-R
5.CN16: INFRA-RED
1 CD-R
2 GND
3 CD-L
4 GND
3.CN31: CD-IN(JST) 4.CN32: CD-IN(JST)
1 GND
2 CD-L
3 GND
4 CD-R
1
4
1
4
9
Hardware Setup
Clip
Clip DIMM
DIMMSocket
Notch
Installing the Processor
For easy installation of the CPU, it is recommended that you remove all
Cards in PCI slots first.
• Unpack the CPU and identify the pin 1 corner of the CPU.
• Match pin 1 of the CPU with pin 1 of the CPU socket. The pin 1 corner of
the CPU socket is designated by a small triangle printed on the motherboard.
• CarefullyinserttheCPUintotheCPUsocketandmovethemetalarmdownward
to replace it in its original position. Change any jumper settings as
detailed in the manual.
The small circle marked on the top of the CPU designates the pin 1 corner.
If a heat sink is attached and covers the top of the CPU, identify the pin 1
corner by turningthe CPU over. Locate the small gold finger that extends
from one corner of the large central square portion of the CPU. The gold
finger points towards pin 1, which is also uniquely identified by a square pad.
Positioning the CPU incorrectly in the socket can permanently damage
the CPU and the computer when you turn on the system.
5. Position the DIMM above the socket. Align the two small notches in the
bottom edge of the DIMM with the keys in the socket.
6. Insert the bottom edge of the DIMM into the socket.
7. When the DIMM is seated, push down on the top edge of the DIMM until the
retaining clips at the ends of the socket snap into place. Make sure the
clips are firmly in place.
8. Replace the computer cover.
9. If you installed a DIMM with ECC memory, start the computer and use the
ECC Configuration feature in Setup to enable the use of ECC.
10
Technical Reference Booklet
BIOS SETUP
This chapter discusses Award’s Setup Program built into the ROM BIOS. The
Setup Program allows users to modify the basic system configuration. This
special information is then stored in battery-backed RAM, which retains the
setup information when the power is turned off.
Starting Setup
The Award BIOS is immediately activated when you turn on the computer. The
BIOS reads the system information contained in the CMOS and begins the
process of checking out the system and configuring it. When it finishes, the
BIOS will seek an operating system on one of the disks and then launch and
turn control over to the operating system .
While the BIOS is in control, the Setup Program can be activated :
1. By pressing <Del> immediately after switching the system on, or
2. By pressing the <Del> key when the following message appears briefly at
the bottom of the screen during the POST (Power On Self Test )
Press DEL to enter SETUP
If the message disappears before you can respond and you still wish to enter
Setup, restart the system to try again by turning it OFF then ON or pressing the
“RESET” button on the system case. You may also restart by simultaneously
pressing the <Ctrl>, <Alt>, and <Delete> keys. If you do not press the keys at
the correct time and the system does not reset, an error message will be
displayed and you will again be asked to ...
PRESS F1 TO CONTINUE, DEL TO ENTER SETUP
Getting Help
Press F1 to pop up a small help window that describes the appropriate keys to
use and the possible selections for the highlighted item. To exit the Help
Window press <Esc> or the F1 key again.
In Case of Problems
If, after making and saving system changes with the Setup Program, you
discover that your computer does not reset, use the Award BIOS defaults to
override the CMOS settings.
Main Menu
Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear
on the screen. The Main Menu allows you to select from various setup functions
and two exit choices. Use the arrow keys to select among the items and press
<Enter> to accept and enter the sub-menu.
Inhaltsverzeichnis
Andere V-tech Hauptplatine Handbücher
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
