V-tech Ia5839 - Cordless Phone - Operation Bedienungsanleitung

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always

be followed to reduce the risk of fire, electric shock and injury, including the

following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid

or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen

sink or swimming pool).

5. Do not place this product on an unstable surface, such as a table, shelf, or

stand. The product may fall, causing serious damage.

6. Slots and openings in the back or bottom of the base unit and handset are

provided for ventilation. To protect them from overheating, these openings

must not be blocked by placing the product on a soft surface such as a bed,

sofa or rug. This product should never be placed near or over a radiator or

heat register. This product should not be placed in any area where proper

ventilation is not provided.

7. This product should be operated only from the type of power source indicated

on the marking label. If you are not sure of the type of power supply in your

home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not install this product

where the cord may have anyone walking on it.

9. Never push objects of any kind into this product through slots in the base or

handset as they may touch dangerous voltage points or short out parts that

could result in a risk of fire or electric shock. Never spill liquid of any kind on

the product.

10.To reduce the risk of electric shock, do not disassemble this product, but

take it to an authorized service facility. Opening or removing parts of the

base or handset other than specified access doors may expose you to

dangerous voltages or other risks. Incorrect reassembling can cause

electric shock when the product is subsequently used.

11. Do not overload wall outlets and extension cords as this can result in the

risk of fire or electric shock.

12.Unplug this product from the wall outlet and refer servicing to an authorized

service facility under the following conditions:

Important Safety Instructions

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled onto the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions, as improper adjustment of other controls may result in

damage and often requires extensive work by an authorized technician

to restore the product to normal operation.

E. If the product has been dropped and the base and/or handset has been

damaged.

F. If the product exhibits a distinct change in performance.

13.Avoid using a telephone (other than cordless) during an electrical storm.

There is a remote risk of electric shock from lightning.

14.Do not use the telephone to report a gas leak in the vicinity of the leak.

15.Only put the handset of your telephone next to your ear when it is in normal

talk mode.

Enhanced 5.8GHz Technology - Dual band transmission combines the best of

5.8GHz and 900MHz technologies, providing enhanced performance over

standard cordless telephones.

Before You Begin

6. Batteries (2)

7. Belt Clips (2)

8. User’s Manual

9. Charger Power Adaptor

10. Wall Mount Bracket

Parts Check List

1. Base Unit

2. Handsets (2)

3. Handset Charger

4. Base Power Adaptor

5. Telephone Line Cord

Handset x 2

Base Unit

Handset Charger

Battery x 2 Belt Clip x 2 Charger

Power Adaptor

Base Power Adaptor Telephone Line Cord User’s Manual

(English and Spanish)

Wall Mount Bracket

To purchasereplacementbatteries, visitus onthe webat www.vtechphones.com

or call VTech Communications, Inc. at 1-800-595-9511. In Canada, call VTech

Telecommunications Canada Ltd. at 1-800-267-7377.

The Handset Layout

1. Antenna

2. Earpiece

3. LCD

4. Left and Right Arrow Keys

5. Phone/Flash Key

6. Dialing Keys (0-9,*,#)

7. Chan/Delete Key

8. Microphone

9. Headset Jack

10. Select Key

11. Off Key

12. Hold Key

13. Redial/Pause Key

14. Prog Key

The Base Unit Layout

1. Message LED

2. Locate Handset key

3. Charging/In use LED

4. Telephone Line Jack

5. DC Connector Jack

Getting Started

Setup

Installation and Charge of Battery

1. Install the battery. Use only VTech batteries.

a) Remove battery com-

partment cover by

pressing on the in-

dentation and sliding

downward.

b) Align the two holes in the plug with the

socketpins,then snap thepluginto place.

c) Place the battery in the compartment

with the wires in the lower right corner.

d) Replace the battery compartment cover.

e) If the battery is not already charged,

place the handset in its base or charger

and allow to charge for 10 -12 hours (or

over- night). After that, be sure to place

the handset in its base or charger when

not in use to ensure maximum daily

peformance.

Connecting Power to Base Unit

1. Choose a location for the base

near an electrical outlet and a

telephone jack. This phone requires

a modular telephone jack and a

standard electrical outlet (110V

AC) not controlled by a wall switch.

Connect the

Power Cord

Standard electrical outlet

2. Plug the DC connectors to the base. Plug the AC adaptors into an electrical

outlet. Connect the telephone line cord to the jack on the base, and the other

end to a modular telephone jack, as illustrated on the next page.

2. If the phone will not be used for long periods of time, remove the battery to

prevent possible leakage.

Getting Started

Setup

Connect the

Telephone

Line Cord

Modular telephone jack

NOTE: Install the base unit away from electronic equipment, such as personal

computers, television sets or microwave ovens. Avoid excessive heat, cold, dust

or moisture.

Connecting to Phone Line

Before connecting to the phone, make

suretoproperlychargethebatteryforat

least10 - 12 hours.

Plug one end of the telephone line cord

into the jack on the bottom of the base

unit. Plug the other end of this cord into

thewall jack.

Battery Care and Maintenance

• The maximum standby time on a fully charged battery is six days. Average

talk time on a fully charged battery is five hours.

• The battery needs charging when:

— A new battery is installed in the handset.

— The phone beeps twice every five seconds.

— The screen displays BATTERY LOW and the low battery icon.

• Place the handset in its base so the CHARGING light turns on. The battery

is typically fully charged in 12 hours.

• You can keep the battery fully charged by returning the handset to its base

after each use.

• If you repeatedly get a low battery indicator, even after charging overnight, the

battery should be replaced. Use only VTech batteries.

CAUTION! To reduce the risk of fire or injury to persons or damage to

the telephone, read and follow these instructions carefully:

Charge the battery provided with or identified for use with this

product only in accordance with the instructions and limitations

specified in the user’s manual.

Check for Dial Tone

Afterthebatteryischarged,pickupthehandsetandpress /FLASH.Youshouldhear

adialtone.

LOW BATTERY indication: If the battery power

becomes low, a low-battery icon will be shown

at the lower left corner of handset display. The

handset will beep until you place the handset in

the charger. When in standby mode, the low-

battery display is shown:

BATTERY LOW

1/0 1 12:00

Getting Started

Setup

Set Date and Time

Ifyou subscribetocallerID service,thedate andtimewillbe setautomaticallywith

thefirst incomingcall.If you donothave callerIDservice, you cansetthe dateand

time manually:

• Press PROG on the handset.

• Press or until DATE/TIME is displayed. Press SELECT.

• The month is flashing. Press or until the screen displays the correct

month. Press SELECT.

• The day is flashing. Press or until the screen displays the correct

day. PressSELECT.

• The hour is flashing. Press or until the screen displays the correct

hour. Press SELECT.

• The minute is flashing. Press or until the screen displays the correct

minute. Press SELECT.

•AM or PM is flashing. Press or to choose between AM or PM.

Press SELECT.

Wall Mounting

The wall mount bracket is designed for use on standard wall mount plates only.

1. Run the power and telephone line cords through the slots in the bracket,

connecting them to the jacks located on the underside of the base.

2. Plug the AC adapter into an electrical outlet. If the battery has not been

previously charged, place the handset in the base, and allow it to charge for 10-

12 hours (or overnight).

3. Connect the telephone line cord to the wall jack.

4. Line up the tabs on the

wall mount bracket with the

slots on the bottom of the

base unit. Snap the bracket

firmly in place.

5. Mount the base on the

wall. Position the base unit

so the mounting studs will

fit into the holes on the wall

mount bracket. Slide the

base unit down on the

mounting studs until it locks

into place.

Basic Operation

Telephone Operation

/CID

• While on a call, press to

decrease the volume. A

double beep will sound

when you reach the mini-

mum setting.

• While phone is not in use,

presstodisplaycallerIDin-

formation.

• While entering number or

letters, press to delete last

character entered.

/FLASH

• To make a call, press then

dial the number. or dial the

number (use to back-

space and correct digits),

then press /FLASH

• During a call, press to re-

ceive an incoming call, if

Call Waiting is activated.

• To answer a call, press this

oranykeyexcept (OFF).

•Ifyouhave callwaitingser-

vice, you will hear a beep

if someone calls while you

are on a call. Press RE-

DIAL/PAUSEtoputthefirst

call on hold and take the

new call. Press again to

switch back and forth be-

tween the calls.

HOLD

• Press to put a call on hold.

Press again or press /

FLASH to release hold.

-OR-

• Use the extension to pick

up the call.

CHAN/DELETE

• Press to switch to a clear

channel while on a call.

• When viewing the call log,

press to delete the current

recorddisplayed.

• While handset is in idle

mode,press and hold to de-

leteallrecordsinthecalllog.

SELECT

• Use SELECT inconjunction

with PROG during handset

programming.

• While on a call, press to

transfer the call to the other

handset.

• While on a call, press to in-

creasethevolume.Adouble

beep will sound when you

reach the maximum setting.

• While phone is not in use,

press to display phonebook

entries.

• Whileenteringletters,press

toadvancecursor.

(OFF)

• Press to end a call, or place

handsetinbaseorcharger.

• While under program ming,

press to exit.

• Whileunderpaging,pressto

cancel.

REDIAL/PAUSE

• To call last number dialed,

pressREDIAL/PAUSE,then

press /FLASH. or

• Press /FLASH, then

pressREDIAL/PAUSE.

• Todelete the lastnumberdi-

aledrecord,presstwicewhile

handset is idle.

• While entering numbers,

pressREDIAL/ PAUSEtoin-

sert a dialing pause.

PROG

• Press to enter programming

mode with handset idle (on

hook).

Basic Operation

Telephone Operation

Base and Charger Operation

Message Waiting

Indicator

• Ifyousubscribetotele-

phone company voice

mail with a visual mes-

sage waiting signal,

this light flashes, and

MESSAGESWAITING

displays in the hand-

set screen, when you

have voice mail wait-

ing.

Charging/In Use

Indicator

• Flashes slowly when

the handset is in use.

• Flashes rapidly when a

call is on hold.

• Glows steadily when

the handset is charging

in its base.

Page/Handset Lo-

cator

• Press to page the hand-

sets. Press again, press

OFF on handset, or

place handset in the

basetocancelthe page.

Andere Handbücher für ia5839 - Cordless Phone - Operation

Inhaltsverzeichnis

Andere V-tech Telefon Handbücher

V-tech

V-tech EriseBusinessSystem UP406 Bedienungsanleitung

V-tech

V-tech CS6114 Bedienungsanleitung

V-tech

V-tech i6720 Bedienungsanleitung

V-tech

V-tech CS6648-2 Bedienungsanleitung

V-tech

V-tech CS2000 Series Bedienungsanleitung

V-tech

V-tech ErisTerminal VSP610AErisTerminal VSP608A Bedienungsanleitung

V-tech

V-tech Analog Contemporary Series Bedienungsanleitung

V-tech

V-tech CTM-S2115 Bedienungsanleitung

V-tech

V-tech FS6325A Bedienungsanleitung

V-tech

V-tech Contemporary Series A2100 Bedienungsanleitung

V-tech

V-tech Analog Classic Series Bedienungsanleitung

V-tech

V-tech CTM-S2312 Bedienungsanleitung

V-tech

V-tech i5868 Bedienungsanleitung

V-tech

V-tech i6785 Bedienungsanleitung

V-tech

V-tech ia5863 Bedienungsanleitung

V-tech

V-tech VS 113 Bedienungsanleitung

V-tech

V-tech DS4122-X Bedienungsanleitung

V-tech

V-tech vt1122 Bedienungsanleitung

V-tech

V-tech CTM-S2412 Bedienungsanleitung

V-tech

V-tech SIP Next Gen Series Bedienungsanleitung

V-tech

V-tech ErisTerminal VSP885G Bedienungsanleitung

V-tech

V-tech ia5824 Einrichtungshandbuch

V-tech

V-tech IS 8121-3 Bedienungsanleitung

V-tech

V-tech i6763 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

D-Link

D-Link DWR-720/PW Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Panasonic

Panasonic KX Series Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

V-tech ia5839 - Cordless Phone - Operation Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken