Valcom V-DW11025B Montageanleitung

V-DW11025B / V-DW11040B

Wireless Digital Clock

Installation and Programming Manual V1.1

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019

USA

+1 540-563-2000 P.

+1 540-362-9800 F.

www.valcom.com

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019

USA

+1 540-563-2000 P.

+1 540-362-9800 F.

www.valcom.com

Table of Contents

V-DW11025B / V-DW11040B Wireless Digital Clock

Table of Contents—2

Installation

Included in the Kit—3

Surface (Wall) Mount Installation—4

Surface (Wall) Mount Installation (continued)—5

Double Mount Installation—6

Double Mount Installation (continued)—7

Double Mount Installation (continued)—8

Wiring Information

Wiring and Jumper Settings—9

Support

Frequently Asked Questions—10

Troubleshooting—11

*Manuals may change without prior notice

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019

USA

+1 540-563-2000 P.

+1 540-362-9800 F.

www.valcom.com

Included in the Kit

Surface Mount - 120VAC Kit

Kit will be labeled: D-PK-3-110-S

• 120VAC or 240VAC Harness (18 AWG), Black, Green, White

Kit will be labeled: D-MK-WLL-PLTC-1

• 4 - 6-32 x 1” Machine Flat Screws

• 4 - 6-19 x 1/2” Flat Head Screws

• 4 - 8-32 x 7/19” Screws

• 2 - 8-32 x 7/16” Screws

Below is a list of all the items included in the installation kit. The items in the kit will correspond to the type of mounting and voltage

option chosen.

Installation

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019

USA

+1 540-563-2000 P.

+1 540-362-9800 F.

www.valcom.com

Surface (Wall) Mount Installation

Installation

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019

USA

+1 540-563-2000 P.

+1 540-362-9800 F.

www.valcom.com

1. Mount Housing to Wall and/or Gang Box - To mount the housing to the wall, install two (2) wall anchors into the wall (not

supplied in kit) and take two pan head screws no larger than #8 (also not supplied in kit) and drive them into the anchors leaving

an 1/8th inch gap between the head of the screw and the wall. Mount the housing to the wall by lining up the two keyholes in the

back of the housing with the two screws with the 1/8 inch gap and slide the housing onto the heads of the screws. Next, mark the

2 mounting holes at the bottom of the housing on the wall. Remove the housing and install wall anchors at this location. Hang the

housing on the keyholes and install the bottom screws. To mount the housing to the gang box, take the four (4) 6-32 x 1” screws

(supplied in kit) and screw them through the four holes in the center of the inside of the housing and the four holes in the gang

box.

Note: If using a metal gang box, a ground must be provided to the gang box.

2. Feed Wiring Into the Housing - Take the wire coming from the inside of the gang box and feed it through the hole in the

middle of the housing.

3. Plug and Secure Wiring - Loosen the provided wire clamp (comes attached to the inside of the housing) and slip excess wiring

through and tighten the clamp. After securing excess wiring, connect the wiring into the appropriate connector on the back of the

display board. (See the Wiring and Jumper Settings on page 9).

4. Mount Display Board to Housing - Using the four (4) self tapping, 6-19 x 1/2” flat head screws (supplied in the assembly kit),

take the display board and screw it to the front side of the clock housing (4 screws per clock).

5. Snap on Filter - Take the red filter bezel and snap it on to the front side of the housing.

6. Snap on Frame - Take the gray frame and snap it on to the front side of the housing.

Surface (Wall) Mount Installation (continued)

Installation

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019

USA

+1 540-563-2000 P.

+1 540-362-9800 F.

www.valcom.com

Double Mount Installation

Installation

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019

USA

+1 540-563-2000 P.

+1 540-362-9800 F.

www.valcom.com

Double Mount Installation (continued)

*For metal mounting bracket: Use a wall anchor that can support 50 lbs or more with a maximum

screw size of #8

1. Install metal mounting bracket - First, remove the metal mounting bracket from the inside of the double mount base by

unscrewing the two (2) 6-32 x 1/2” screws located on the underside of the base (save these screws for step #5). Next, screw the

metal mounting bracket to the wall or ceiling in which the clocks are being installed. To mount to the double gang switch box, screw

the four (4) 6-32 x 1” screws (supplied in the assembly kit) through the inner four holes of the metal mounting bracket. Use the outer

four holes to mount to the anchors in the wall (both anchors and screws are not supplied in kit).

Note: If using a plastic switch box, a ground wire must be routed through the switch box and into one (1) of

the four (4) metal mounting bracket screws in order to provide ground to the metal mounting bracket. The metal

mounting bracket

MUST

be secured by both the screws going to the switch box

AND

the anchors going into the

wall.

2. Mount clock housings to pole - Align the hole in the center each housing with one of the three holes on the mounting pole

where the wiring will be routed (the installer will choose which hole at the end of the pole to use based on how far they want the

clock to sit from the wall). Screw from the inside of the housing into the four holes surrounding the hole in the center of the housing

using the four (4) 8-32 x 7/16” screws (supplied in the assembly kit - 4 screws per clock), securing both housings to the mounting pole.

Note: End caps from one side of each clock must be removed to mount both clocks to the mounting pole.

Remove one end cap from each clock from the side in which the mounting pole enters the clock.

*Instructions continued on next page

3. Screw both housings together - Using the two (2) self tapping, 6-19 x 7/16” screws (supplied in the assembly kit), screw both

back sides of the clock housings together (2 screws per clock).

Installation

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019

USA

+1 540-563-2000 P.

+1 540-362-9800 F.

www.valcom.com

Double Mount Installation (continued)

4. Feed wiring through base and pole - Take the wiring coming from the switch box and begin to feed it through the center of

the base of the mounting assembly until it emerges from the hole in the center of the clock housing.Make sure there is roughly 1.5’

of wiring coming from the switch box. Perform this task for both clocks.

5. Snap and screw base to metal mounting bracket - Snap the base to the metal mounting bracket by first making contact with

the lip in the upper side of the base and the metal mounting bracket. When the base has been snapped onto the bracket, take

the two (2) 6-32 x 1/2” pan head screws that originally came installed on the base and screw them back into the two holes on the

underside of the base to secure the base to the metal mounting bracket.

6. Connect switch box wires to clock harness - Take the wiring harness supplied with the clock and make all necessary

connections between the wiring harness and the switch box wires using wire nuts. Perform this task for both clocks.

7. Plug and secure wiring - Loosen and slip excess wiring through provided wire clamp (comes attached to each housing) and

tighten the clamp. After securing excess wiring, connect the wiring harness into the appropriate connector on the back of the

display board. Perform this task for both clocks. (See the Wiring and Jumper Settings on page 9).

8. Mount display board to housing - Using the four (4) self tapping, 6-19 x 1/2" flat head screws supplied in the assembly kit,

take the display board and screw it to the front side of the clock housing (4 screws per clock).

9. Snap on filter - Take the red filter bezel and snap it on to the front side of each clock housing.

10. Snap on frame - Take the gray frame and snap it on to the front side of each clock housing.

Installation

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019

USA

+1 540-563-2000 P.

+1 540-362-9800 F.

www.valcom.com

Wiring Information

Wiring and Jumper Settings

**Jumper Position

JP 1

JP 4

JP 5

JP 6

JP 2

JP 3

Power Settings

No Connection

120VAC @ 0.1A (BLK)

No Connection

120VAC @ 0.1A (WHT)

no Connection

J1 - Sync Inputs J2 - User Inputs

12 3 4 5 6 7 8 9 12 3 4 5 6 7 8 9

AC / DC Com

Dukane Reset

Dukane Pulse

Dry Contact

3.3VDC@20ma

Common

User Input 4

User Input 3

User Input 2

User Input 1

12VDC@40ma

Each User Input is

a Contact Closure

J3 - Relay Output

*Relay 1 N.O.

*Relay 2 N.O.

*Contact Rating

0.3A @ 120VAC

**Note: Be sure to have a jumper present on Pin 1 & 2 or Pin 2 & 3. Below are the

Jumper Positions and what function each corresponds with.

Note: Jumpers are only read on power up.

1 2 3

Jumper Position Pin 1 & Pin 2 Pin 2 & Pin 3

JP 1 12 Hour Time 24 Hour Time

JP 2 Bright Dim

JP 3 Time Display Only Alternating Date/Time Display

JP 4 N/A N/A

JP 5 N/A N/A

JP 6 N/A N/A

Wiring Information

J7 - RS485

1 2 3 4

Input A

Input B

Output A

Output B

Please note that items within the

dotted lines are applicable only to the

SBL 3200 or 3300 series.

*Jumpers 4, 5 and 6 must be in the Pin 1 & Pin 2 position.

JP 4 *See Note Below

JP 5 *See Note Below

JP 6 *See Note Below

Valcom, Inc.

5614 Hollins Road

Roanoke, VA 24019

USA

+1 540-563-2000 P.

+1 540-362-9800 F.

www.valcom.com

Frequently Asked Questions

Will the clock cause interference with any of my other wireless devices?

No, the Valcom Wireless Digital Clock works on 915 - 928 MHz frequency-hopping technology. The clock switches frequencies

automatically when the receiver and transmitter are open, thus interference is avoided.

How long does it take for the clock to receive a signal?

Upon power up, the clock will look for the signal for 30 minutes. The Valcom Wireless Digital Clock will look for the signal every minute

thereafter.

Do the Valcom Wireless Digital Clocks work together with Valcom’s wireless analog clocks?

Yes, the Valcom Wireless Digital Clocks work integrally with Valcom’s wireless analog clocks.

How many ways can I mount the Valcom Wireless Digital Clock?

The clock can be mounted in either surface or double mount. Please see pages 4 through 8 for more information on mounting

instructions.

Can the Valcom Wireless Digital Clock be used as an independent clock?

No, the Valcom Wireless Digital Clock requires a communication input and must be used with either a Valcom Transceiver or Repeater.

What will happen if the clock is not receiving a signal?

The colon on the display will flash every second.

How can the clock be powered?

The clock is available in 120VAC models.

Support

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Valcom Uhr Handbücher

Valcom

Valcom VIP-431A-DS Bedienungsanleitung

Valcom

Valcom V-D11025B Bedienungsanleitung

Valcom

Valcom VE4122-A12 Bedienungsanleitung

Valcom

Valcom VIP-D425DS Bedienungsanleitung

Valcom

Valcom 12" Bedienungsanleitung

Valcom

Valcom VIP-429A-A Bedienungsanleitung

Valcom

Valcom VIP-MC Bedienungsanleitung

Valcom

Valcom VIP-A12 Bedienungsanleitung

Valcom

Valcom VIP-D425A Bedienungsanleitung

Valcom

Valcom V-D11025A Montageanleitung

Valcom

Valcom V-D2425B Montageanleitung

Valcom

Valcom VIP-A12ADS Bedienungsanleitung

Valcom

Valcom V-A2412 Bedienungsanleitung

Valcom

Valcom IP Solutions VIP-A12DS Bedienungsanleitung

Valcom

Valcom V-A2412 Bedienungsanleitung

Valcom

Valcom VIP-A12ADS Bedienungsanleitung

Valcom

Valcom VIP-D625 Bedienungsanleitung

Valcom

Valcom V-AW12A Bedienungsanleitung

Valcom

Valcom VIP-429A-A-SA Bedienungsanleitung

Valcom

Valcom VIP-A12A Bedienungsanleitung

Valcom

Valcom InformaCast VIP-431-A-IC Bedienungsanleitung

Valcom

Valcom V-AW12A Bedienungsanleitung

Valcom

Valcom VIP-D425ADS Bedienungsanleitung

Valcom

Valcom VIP-D425 Bedienungsanleitung

Beliebte Uhr Handbücher anderer Marken

Silicon Laboratories

Silicon Laboratories SI5324 Bedienungsanleitung

Heathkit

Heathkit GC-1005 Bedienungsanleitung

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Bedienungsanleitung

Andrew O'Malley

Andrew O'Malley DOTKLOK Bedienungsanleitung

ALGE-Timing

ALGE-Timing ASC3 Bedienungsanleitung

Bodet

Bodet Profil 960 Bedienungsanleitung

Nixie Clock

Nixie Clock Divergence Meter Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8256-AL Bedienungsanleitung

Mini Gadgets

Mini Gadgets MCPro Bedienungsanleitung

Casio

Casio TMR-200 Bedienungsanleitung

Progetti

Progetti ILTEMPOSTRINGE Handbuch

BVItech

BVItech BV-101 Bedienungsanleitung

Progetti

Progetti KALIMERO Handbuch

La Crosse Technology

La Crosse Technology WT-3141b Handbuch

La Crosse Technology

La Crosse Technology W86531 Bedienungsanleitung

Sharp

Sharp SPC900 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-50447 Bedienungsanleitung

Datexx

Datexx DF0063 Bedienungsanleitung