Valcom VIP-148AL Bedienungsanleitung

1 947810

CAUTION: To reduce the risk of electric shock,

Do not remove cover.

No user serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present within this unit.

This symbol indicates thatthere are

important operating and maintenance

instructions in the literature accompanying

this unit.

Issue 1

VIP-148AL IP Talkback Horn

INTRODUCTION

The VIP-148AL IP Talkback Horn enables

two-way handsfree voice access to a single

location over an IP-based network. This allows a

page zone extension anywhere on the network.

The horn audio level is electronically adjusted via

software. A call switch input connection is

provided for call initiation. Power is provided to

the VIP-148AL via a Power over Ethernet (PoE)

switch meeting the 802.3af specification.

SPECIFICATIONS

Access Methods

PBX, FXO Port w/VIP-811

POTS telephone set w/VIP-811

FXS Port w/VIP-821

SIP telephone system

Features

RJ-45 for network connection

Network activity LEDs

Power over Ethernet (PoE) 802.3af

compatible

Dimensions/Weight VIP-148AL

Horn

7.38” H x 10.0” W x 10.4” D

(18.75cm x 25.4cm x 26.42cm)

Weight: 3.70 lbs. (1.68 kg)

Network Interface

1.62” H x 5.63” W x 3.45” D

(4.11 cm) x (14.30 cm) x (8.73 cm)

with brackets – 8.22” W (20.87 cm)

Weight: 2.10 lbs. (0.95 kg)

Environment

Network Interface:

Temperature: 0 to +40° C

Humidity: 0 to 85% non-precipitating

Horn:

Suitable for indoor or outdoor installation

Nominal Power Requirements

Via 802.3af (PoE) Ethernet Switch: Class 3

Packing List

Qty Item

1 Network Interface

1 VIP-148AL Horn

1 VSP Document

1 “C” Clamp

1 VM-186 RJ-45 Connector

Precautionary Designations

2 947810

FCC Information

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated

in a commercial environment. This

equipment generates, uses and can radiate

radio frequency energy and if not installed

and used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area may cause

harmful interference in which case the user

will be required to correct the interference at

his own expense.

INSTALLATION

Operation:

Provides talkback intercom via Network

connection to customer telephone system or

stand alone telephone set. Interface to customer

telephone system can be via SIP registration,

FXO port or FXS port (additional equipment

required in all cases). The optional call button

may be programmed to initiate a call to one of the

above telephone system interfaces. When the

call is answered, a hands-free communications

path is established to the horn.

Mounting (Network Interface)

The VIP-148AL Network Interface is designed for

wall or table mounting and must be within 100

meters of the network switch.

Mounting (Horn)

The VIP-148AL Horn is designed for most FD

electrical box or wall mounting and must be within

300 meters of the VIP-148AL Network Interface.

See NEMA OS 3-2002 sec.1.2.3.5 for FD box

specifications.

Attaching Speaker to Base

NOTE: For ease of installation, the base can be

attached to the speaker before or after the base

is mounted.

Loosen position adjustment knob

Insert the ball of the base into the socket of

the speaker

Tighten the position adjustment knob

These horns should be mounted 15 to 20 feet

above the floor to allow for best sound

distribution. The units can be mounted to a wall,

a beam or an electrical box.

A “C” clamp is provided with the horns to

allow mounting to a beam. When using the

“C” clamp for mounting, remove the signal

cable from the ball mount. Reinstall an RJ45

connector on the signal cable after mounting,

using the T568B pinout scheme. See Figure

The base has holes punched for a

double-gang square box, but by punching out

additional knockout holes, the base can be

mounted to a single-gang or octagon box

See Figure 2.

Mount the base to wall studs using the two

holes provided. Knockout holes are provided

for punch out should additional holes be

desired. See Figure 3.

The horns may be rotated or moved up and down

to obtain the desired position by loosening the

position adjustment knob at the bottom of the unit

approximately one turn. Make required

adjustments, retighten knob.

Figure 1. Mounting to a Beam with a “C” Clamp

3 947810

Figure 2. Mounting to an Electrical Backbox

Figure 3. Mounting to Wall stud

Power Connections

The only method of powering a VIP-148AL

Network Interface is via a Power over Ethernet

(PoE) switch or power injector meeting the

802.3af specification. Make all required signal

connections before connecting to Ethernet switch

or power injector meeting the 802.3af

specification.

Network Connection

The VIP-148AL Network Interface has one RJ-45

Ethernet network connector and one RJ-45 horn

connector.

Use a standard Ethernet patch cable to connect

the VIP-148AL to an Ethernet switch.

Signal Connections

Audio output connection is made from the Signal

Output. The RJ-45 connector on the horn is

connected directly to the RJ-45 Signal Output

socket on the Network Interface. If additional

length is required, any standard T568B extension

may be used. See Figure 4.

If desired, a normally-open call button may be

connected to the Blue, White/Blue pair of the

horn RJ-45 connector.

The VM-186 RJ-45 connector provides easy

access to these connections.

Status Indicator Lights

The VIP-148AL has 2 status indication lights

located on network jack:

Green LED: (Link) Indicates Ethernet

connection when illuminated.

Yellow LED: (Activity) Indicator flashes to

indicate network activity.

Setup

Information specific to your application will need

to be programmed into the VIP-148AL using a

computer. The PC used for programming should

be connected to the same subnet as the

VIP-148AL. Setup will be done using the IP

Solutions Setup Tool. The IP Solutions Setup

Tool is available for download on the Valcom

website at www.valcom.com/vipsetuptool.

4 947810

TECHNICAL ASSISTANCE

Assistance in troubleshooting is available from

the factory when problems are encountered.

Call (540) 563-2000 and press 1 for Technical

Support or visit our website at

http://www.valcom.com.

Valcom equipment is not field repairable.

Valcom, Inc. maintains service facilities in

Roanoke, VA. Should repairs be necessary,

attach a tag to the unit clearly stating your

company name, address, phone number, contact

person and the nature of the problem. Send the

unit to:

Valcom, Inc.

Repair & Return Dept.

5614 Hollins Road

Roanoke, Va. 24019-5056

VALCOM LIMITED WARRANTY

Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under conditions of

normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the replacement, repair or refund

of any such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim;

2. the defect is not the result of damage, misuse or negligence after the original shipment;

3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts

and labor will be applied to units defaced or physically damaged);

4. freight charges for the return of products to Valcom are prepaid;

5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to

additional charges for parts and labor).

This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable for any

anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation,

maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to the purchase price of the

specific Product covered by the warranty.

Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever including, without

limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.

This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be notified

immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.

Headquarters:

Valcom, Inc.

5614 Hollins Road Roanoke, VA 24019-5056

Phone: (540) 563-2000 FAX: (540) 362-9800

5 947810

RJ45 NETWORK

CONNECTION

SIDE

HORN SIGNAL CONNECTION

HORN

RJ45 NETWORK

CONNECTION

SIDE

STANDARD

RJ45 PATCH CABLE

(T568B)

Typical 568B

RJ-45 Jack

RJ-45

CAT 3/5/6

VM-186

RJ45

WHITE/GREEN

GREEN

WHITE/BROWN

BROWN

BLUE

WHITE/BLUE

BLUE

WHITE/ORANGE

ORANGE

WHITE/GREEN

GREEN

WHITE/BROWN

BROWN

WHITE/BLUE

BLUE

WHITE/ORANGE

ORANGE

HORN

*The Maximum Recommended Distance

From the IP Link to the Horn is 350’.

CALL IN SWITCH

NORMAL OPEN

MOMENTARY CLOSED

(OPTIONAL)

Figure 4. Signal Connections

Inhaltsverzeichnis

Andere Valcom Horn Handbücher

Valcom

Valcom FlexHorn VIP-483-IC Bedienungsanleitung

Valcom

Valcom VIP-480AL Bedienungsanleitung

Valcom

Valcom IP Solutions VIP-483 Bedienungsanleitung

Valcom

Valcom V-9925A Bedienungsanleitung

Valcom

Valcom InformaCast VIP-480L-IC Bedienungsanleitung

Valcom

Valcom V-1048C Bedienungsanleitung

Valcom

Valcom FlexHorn V-1030M Bedienungsanleitung

Valcom

Valcom V-1038 Bedienungsanleitung

Valcom

Valcom Revolution VIP-142-SA Bedienungsanleitung

Valcom

Valcom V-1069 Bedienungsanleitung

Valcom

Valcom V-1050C Bedienungsanleitung

Valcom

Valcom VIP-480L Bedienungsanleitung

Valcom

Valcom VIP-480AL-SA Bedienungsanleitung

Valcom

Valcom VIP-9831 Bedienungsanleitung

Valcom

Valcom V-1030C Bedienungsanleitung

Valcom

Valcom VIP-130L Bedienungsanleitung

Valcom

Valcom V-1048C Bedienungsanleitung

Valcom

Valcom VIP-148AL-IC Bedienungsanleitung

Valcom

Valcom VIP-130AL Bedienungsanleitung

Valcom

Valcom VIP-480AL-IC Bedienungsanleitung

Valcom

Valcom VIP-480L Bedienungsanleitung

Valcom

Valcom V-1090- BG Bedienungsanleitung

Valcom

Valcom V-1090 Flexhorn Bedienungsanleitung

Valcom

Valcom V-1048M Bedienungsanleitung

Beliebte Horn Handbücher anderer Marken

Elk Products

Elk Products 45 Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock DB3 Series Bedienungsanleitung

Altec Lansing

Altec Lansing 811B HF HORN Bedienungsanleitung

RF Elements

RF Elements UltraHorn CC Series Bedienungsanleitung

Edwards Signaling

Edwards Signaling 869DSTR-G1 Series Montageanleitung

Electro-Voice

Electro-Voice HPT94 Bedienungsanleitung

Toa

Toa LE-M124 Bedienungsanleitung

EAW

EAW MR-102B Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR MH30 Bedienungsanleitung

Pequod

Pequod TWISTER 3.1 Bedienungsanleitung

United Pacific

United Pacific 46151 Bedienungsanleitung

Wolo

Wolo OCEAN ALERT 170 Bedienungsanleitung

Vixen Horns

Vixen Horns VXO8315B/4114B Bedienungsanleitung

Altec

Altec 151A PAGING HORN Bedienungsanleitung

aidapt

aidapt VM953 Programmierhandbuch

auna

auna MEG1-HY Bedienungsanleitung

ACR Electronics

ACR Electronics ACR-EM-1A - REV Y Montageanleitung

Behringer

Behringer Eurosound Megaphone XT Bedienungsanleitung