Valley VRI-iS Bedienungsanleitung

www.valleyirrigation.com

VRI-iS

Variable Rate Irrigation

Individual Sprinkler Option

For ICON Control Panels

Installation Manual

0999992_B

VRI-iS Option Installation Manual

This page was left blank intentionally.

Table of Contents

DRAFT COPY

VRI-iS Option Installation Manual................................................................................................................... 1

Table of Contents ............................................................................................................................................. 3

General Information ......................................................................................................................................... 4

About This Manual......................................................................................................................................... 5

Tools Needed ................................................................................................................................................ 5

Safety................................................................................................................................................................. 6

Recognize Safety Information ....................................................................................................................... 6

Safety Messages ........................................................................................................................................ 6

Information Messages ................................................................................................................................ 6

Use of Personal Protective Equipment.......................................................................................................... 7

Conductive Materials and Equipment............................................................................................................ 7

Fall Protection................................................................................................................................................ 7

Minimum Working Clearance ........................................................................................................................ 8

Qualiﬁed Person............................................................................................................................................ 8

Irrigation Equipment near Airports and Crop Dusting Aircraft....................................................................... 8

Overhead Power Lines .................................................................................................................................. 9

Minimal Lockout / Tagout Procedure ........................................................................................................... 10

Sequence of Lockout ................................................................................................................................ 10

Restoring Equipment to Service ............................................................................................................... 10

Installation Instructions................................................................................................................................. 11

Disconnect All Power................................................................................................................................... 11

Install Power Supply and Primary Communication Board........................................................................... 12

Install Slip Ring............................................................................................................................................ 13

Install Cord Connector(s) ............................................................................................................................ 16

Wiring .......................................................................................................................................................... 17

Temporarily Install GPS Position Tower Box................................................................................................ 18

Turn Power On.......................................................................................................................................... 18

Verify Control Panel Software...................................................................................................................... 19

Upgrade Control Panel................................................................................................................................ 19

Setup Control Panel for GPS Position ......................................................................................................... 19

ICON5 / ICONX - Set Current Method...................................................................................................... 20

ICON10 / ICON1 - Set Current Method .................................................................................................... 23

Remove GPS Position Tower Box................................................................................................................ 26

Disconnect All Power ................................................................................................................................ 26

Disconnect Tower Box............................................................................................................................... 26

Install Sprinkler Valves ................................................................................................................................ 27

Connect Cables ........................................................................................................................................ 28

Install Power Supply Tower Boxes ............................................................................................................... 29

Bracket Mounting...................................................................................................................................... 29

Span Pipe Mounting ................................................................................................................................. 29

Connect Cables ........................................................................................................................................ 29

Wire Power Supply Tower Boxes .............................................................................................................. 29

Install GPS Position Tower Box ................................................................................................................... 30

Bracket Mounting...................................................................................................................................... 30

Connect Cables ........................................................................................................................................ 30

Setup................................................................................................................................................................ 31

ICON5 / ICONX........................................................................................................................................... 32

ICON10 / ICON1 ......................................................................................................................................... 38

Field Install And Wiring Diagrams ................................................................................................................ 45

VRI-iS

Control Panel Components for ICON Field Install pn 9312722 ................................................................ 46

Slip Ring Field Install pn 9312418 ............................................................................................................ 47

Valve Field Install pn 9312455 .................................................................................................................. 48

PolySpan Valve Field Install pn 9313117.................................................................................................. 49

Power Supply Tower Box

Field Install pn 9312421............................................................................................................................ 50

Wiring Schematic pn 0999334.................................................................................................................. 51

GPS Position Tower Box

Field Install pn 9312419............................................................................................................................ 52

Wiring Schematic pn 0999346.................................................................................................................. 53

Running Light Field Wiring pn 9310312 ...................................................................................................... 54

Table of Contents

DRAFT COPY

Troubleshooting.............................................................................................................................................. 55

Theory of Operation VRI-iS ......................................................................................................................... 55

System Faults.............................................................................................................................................. 56

Viewing System Faults ................................................................................................................................ 56

System Error Codes.................................................................................................................................... 57

Viewing System Error Codes ...................................................................................................................... 58

Viewing RJ11 Error Codes.......................................................................................................................... 59

ICON5 / ICONX........................................................................................................................................... 60

VRI-iS Diagnostics.................................................................................................................................... 60

Resync Valves ........................................................................................................................................ 60

Test Valve ............................................................................................................................................... 61

Valve Errors............................................................................................................................................ 62

Valve Comm Errors ................................................................................................................................ 62

View Prescription ...................................................................................................................................... 63

Edit Managed Zones................................................................................................................................. 64

ICON10 / ICON1 ......................................................................................................................................... 65

VRI-iS Diagnostics.................................................................................................................................... 65

Resync Valves ........................................................................................................................................ 65

Test Valve ............................................................................................................................................... 66

Valve Errors............................................................................................................................................ 67

Valve Comm Errors ................................................................................................................................ 67

View Prescription ...................................................................................................................................... 68

Edit Managed Zones................................................................................................................................. 69

Fuse Testing ................................................................................................................................................ 70

Power Supply Testing .................................................................................................................................. 70

VRI Primary Communications VDC - Pin/Terminal Call Out/Dip Switch...................................................... 71

Sprinkler Valve LED VRI-iS ......................................................................................................................... 71

Cable VRI-iS - Pin Call Out ......................................................................................................................... 72

Pressure Sensor Cable VRI-iS - Pin Call Out.............................................................................................. 72

Theory of Operation GPS Position .............................................................................................................. 73

Garmin 19x GPS Power Data Cable Wire Color/Function........................................................................... 74

GPS Receiver Accuracy .............................................................................................................................. 74

GPS Signal Errors....................................................................................................................................... 74

GPS Antenna Test ....................................................................................................................................... 75

Use Edit to Setup Control Panel for VRI-iS / GPS Position ......................................................................... 76

ICON5 / ICONX Control Panel Setup-Edit Method ................................................................................... 76

ICON10 / ICON1 Control Panel Setup-Edit Method ................................................................................. 78

GPS Angular Conversion Table ................................................................................................................... 80

Angular Degree Examples .......................................................................................................................... 80

Estimated Drive Unit Speed Tables ............................................................................................................. 81

Parts................................................................................................................................................................. 83

Tower Box Drive Unit Mount ........................................................................................................................ 84

Valve VRI-iS with 10 Ft Cable...................................................................................................................... 85

Valve VRI-iS with 14 Ft Cable...................................................................................................................... 86

Valve with Pressure Switch ......................................................................................................................... 87

VRI-iS PolySpan Valve Assembly With PSI Switch Option.......................................................................... 88

VRI-iS PolySpan Valve Assembly................................................................................................................ 89

Cables VRI-iS .............................................................................................................................................. 90

Panel and GPS Tower Box VRI-iS ............................................................................................................... 91

Tower Box - Pipe Mounting.......................................................................................................................... 92

GPS Tower Box VRI-iS ................................................................................................................................ 94

Power Supply Tower Box VRI-iS.................................................................................................................. 96

Slip Ring VRI-iS........................................................................................................................................... 98

Panel and GPS Hardware VRI-iS.............................................................................................................. 100

Primary Communication Board for Control Panel ..................................................................................... 101

General Information

DRAFT COPY

About This Manual

This manual illustrates the proper installation of the Variable Rate Irrigation Individual Sprinkler (VRI-iS) Option

on a Valley irrigation machine that is equipped with a Valley ICON control panel.

Speciﬁcations, descriptions and illustrative material contained in this manual were based on information avail-

able at the time this publication was approved for printing. Valmont Industries Inc. reserves the right to change

speciﬁcation or design at any time without notice and without incurring any obligation. Speciﬁcations are ap-

plicable to equipment sold within the United States and may vary outside of the United States.

WARNING

•THE ASSEMBLY OF THESE COMPONENTS, INCLUDING ADJUSTING, TESTING AND TROUBLE-

SHOOTING SHOULD BE PERFORMED ONLY BY AN AUTHORIZED VALLEY DEALER.

•IF ANY WIRE IS NOT CONNECTED TO A TERMINAL OR COMPONENT IN THE CONTROL PANEL,

PROTECT THE END OF THE WIRE WITH A WIRE NUT OR EQUIVALENT TO PREVENT DAMAGE

FROM SHORT CIRCUIT OR ARCING.

Tools Needed

• Flat blade screw drivers

• Phillips head screw drivers

• 1/2 in sockets and/or wrenches

• 3/4 in sockets and/or wrenches

• Adjustable wrench

• Pipe wrenches

• Water pump pliers

• Laptop computer

Safety

Recognize Safety Information

This irrigation equipment can be powered by high voltage, which can be extremely dangerous if used improp-

erly. For maximum safety and optimum performance of the machine, all owner/operators and maintenance

personnel must read and understand the owner/operator manual(s), all safety messages in this manual and

safety signs/decals on the machine before operating this equipment.

Anyone assembling, operating, servicing or maintaining this machine must read and understand all opera-

tion, maintenance, troubleshooting, testing, installation, assembly instructions and all safety messages in this

manual before operating the machine or beginning any maintenance, troubleshooting, testing, installation or

assembly of components.

These instructions alert you to certain things you should do carefully; if you don’t, you could hurt yourself or

others, hurt the next person who operates the equipment, or damage the equipment.

Safety Messages

Safety messages in this manual are preceded by the hazard symbol and one of three words: DANGER, WARN-

ING or CAUTION. These messages alert you to potential hazards that could hurt you or others and or cause

property damage.

!This HAZARD SYMBOL is used to alert you to information about unsafe actions or situations, and may

be followed by the word DANGER, WARNING or CAUTION.

!DANGER

The HAZARD SYMBOL used with the word DANGER describes immediate hazards that can result in severe

personal injury or death.

!WARNING

The HAZARD SYMBOL used with the word WARNING describes unsafe actions or situations that can result in

severe injury, death and/or major equipment or property damage.

!CAUTION

The HAZARD SYMBOL used with the word CAUTION describes unsafe actions or situations that can result in

injury, and/or minor equipment or property damage.

Information Messages

Important information messages in this manual are preceded by the word NOTE.

NOTE

The word NOTE is used to alert you to information that describes procedures or tips to help you install, operate

or maintain your equipment properly.

Safety

Use of Personal Protective Equipment

• People working in areas where there are potential electrical hazards must use, personal protective equipment

that is appropriate for the speciﬁc parts of the body to be protected and for the work to be performed. Refer to

U.S. Occupational Safety & Health Administration (OSHA) Regulations (Standards - 29 CFR) Safeguards for

personnel protection. - 1910.335, or applicable national, state or local regulations, for additional information.

• Personal protective equipment must be maintained in a safe, reliable condition and periodically inspected or

tested.

• Protective shields, protective barriers, or insulating materials must be used to protect each person from

shock, burns, or other electrically-related injuries while that person is working near exposed energized parts

which might be accidentally contacted or where dangerous electric heating or arcing might occur. When nor-

mally enclosed live parts are exposed for maintenance or repair, they must be guarded to protect unqualiﬁed

persons from contact with the live parts.

• Safety signs and tags. Safety signs, safety symbols, or accident prevention tags must be used where neces-

sary to warn people about electrical hazards which may endanger them.

Conductive Materials and Equipment

Materials and equipment that can conduct electricity must be handled in a way that will prevent them from

contacting energized power lines, exposed conductors or circuit parts.

• When handling long conductive objects (such as but not limited to truss rods, pipes, angles and ladders) in

areas with energized power lines, exposed conductors or circuit parts, work practices (such as the use of

insulation, guarding, and material handling techniques) must be used to minimize the hazard.

• Portable ladders must have non-conductive side rails.

• Do not wear conductive articles of jewelry and clothing (such as but not limited to watch bands, bracelets,

rings, key chains, necklaces, metalized aprons, cloth with conductive thread, or metal headgear) that could

come in contact with energized power lines, exposed conductors or circuit parts.

Fall Protection

Identify potential fall hazards and determine if fall protection equipment is appropriate for the task, before begin-

ning the work. Pay attention to hazards associated with routine and non-routine tasks. Inspect fall protection

equipment (harnesses, lanyards) and devices (guardrails, tie-off points) before each use. Use fall protection

equipment if required for the job. Be sure the fall protection equipment is right for the task, ﬁts properly, and is in

good condition. Refer to U.S. Occupational Safety & Health Administration (OSHA) Regulations Standards - 29

CFR 1926.500, 1926.501 and 1926.502, or applicable national, state or local regulations for more information.

• When using scaffolds, make sure there is proper access, full planking, stable footing, and guard railing.

• When using a boom lift, keep feet ﬁrmly on the platform of a boom lift, use fall protection equipment tied-off

at all times to the guardrail or tie-off point.

• When using a ladder, make sure the ladder is non-conductive and the correct size for the task. Read the

ladder user instructions and be sure the ladder is in good condition. Make sure ladder is set on stable footing

and at the correct angle.

Safety

Minimum Working Clearance

To reduce the risk of injury, all persons require adequate working clearance around the electrical panel or other

electrical equipment. The table below identiﬁes the minimum working clearance needed. Refer to U.S. Occupa-

tional Safety & Health Administration (OSHA) Regulations (Standards - 29 CFR) Safeguards for personnel pro-

tection. -1910.303(g)(1)(i), or any other applicable national, state or local regulations, for additional information.

MINIMUM WORKING CLEARANCE 0-600 VOLTS

WIDTH

OF WORKING

CLEARANCE

AREA

HEIGHT

OF WORKING

CLEARANCE

AREA

MINIMUM WORKING CLEARANCE

IN FRONT OF ELECTRICAL PANEL/EQUIPMENT

EXPOSED LIVE PARTS

ON ONE SIDE OF WORK

SPACE AND NO LIVE

GROUNDED PARTS ON

THE OTHER SIDE.

EXPOSED LIVE PARTS

ON ONE SIDE OF WORK

SPACE AND LIVE

GROUNDED PARTS ON

THE OTHER SIDE.

EXPOSED LIVE PARTS

ON ONE SIDE OF WORK

SPACE AND EXPOSED

LIVE PARTS ON THE

OTHER SIDE.

30 in (760 mm)

MINIMUM OR

WIDTH OF

ENCLOSURE,

WHICH EVER IS

GREATER

78 in (1980 mm)

MINIMUM OR

HEIGHT OF

ENCLOSURE,

WHICH EVER IS

GREATER

36 in (915 mm) MINIMUM 42 in (1065 mm) MINIMUM 48 in (1220 mm) MINIMUM

Concrete, brick or tile walls shall be considered as grounded.

Qualiﬁed Person

A Qualiﬁed Person is one who, by possession of a recognized degree, certiﬁcate, or professional standing, or

who by extensive knowledge, training, and experience, has successfully demonstrated his/her ability to solve or

resolve problems related to the subject matter, the work, or the project.

Only qualiﬁed persons may work on electric circuit parts or equipment that have not been de-energized.

Refer to U.S. Occupational Safety & Health Administration (OSHA) Regulations Standards - 29 CFR 1926.32(m)

and 1910.333, or applicable national, state or local regulations for additional information.

Irrigation Equipment near Airports and Crop Dusting Aircraft

• If any part of the irrigation machine comes within 3200 ft (975 m) of an airport runway, especially the ap-

proach (ends) of the runway, additional warning markers may be required. In the United States, CFR Title 14,

Chapter I, Subchapter E, Part 77 – Safe, Efﬁcient Use, and Preservation of the Navigable Airspace describes

when marking is needed.

This document is available at: www.ecfr.gov

• Marking requirements vary depending on the location of the irrigation equipment relative to the runway, the

type of airport (Civil, Military, or Heliport) and other factors. Contact the local airport authority for guidance

and speciﬁc recommendations. In the United States, guidelines for marking structures near airports are

published by the Federal Aviation Administration in Advisory Circular AC 70/7460-1L – Obstruction Marking

and Lighting.

Available here: www.faa.gov/regulations_policies/advisory_circulars

• For irrigation machines near private or unregulated airﬁelds, including farm-based airstrips, Valley strongly

recommends complying with the same standards and requirements as Civil airports as shown in Part 77.

• Regulations vary by country, contact your local aviation authority for guidance.

Overhang cables, including overhang back cables are a particular danger. In locations where low-ﬂying

aircraft are likely, such as within 1,500 ft (457 m) of an end of an airport runway, or where crop dusting aircraft

are common, Valley recommends adding obstruction markers to overhang cables to improve their visibility.

For large overhangs (36 ft / 10.97 m Heavy Duty and longer), ﬁve 12 in (300 mm) or 20 in (500 mm), aviation

orange marker balls are sufﬁcient. One near the rabbit ears, two in the middle of the back cables and two in

the middle of the highest overhang cables. Refer to Section 3.5 in AC70/7460-1 for additional details. Aviation

marker balls are available online and from a variety of aviation and airport safety equipment providers.

Safety

Overhead Power Lines

Assembling, towing or transporting irrigation machine components such as but not limited to the pivot point,

linear cart, span/drive unit assemblies, overhangs and/or corner assemblies underneath or near power lines is

extremely dangerous because of the risk of electrocution.

Operating equipment that elevates irrigation machine components, such as but not limited to an aerial lift or

crane, near power lines is extremely dangerous because of the risk of electrocution. Only qualiﬁed personnel

should operate this type of equipment. Before operating the equipment, qualiﬁed personnel must read the

equipment manufacturers’ operating and safety instructions.

• Refer to U.S. Occupational Safety & Health Administration (OSHA) Regulations (Standards - 29 CFR) Cranes

and derricks. - 1926.550, or any other applicable national, state or local regulations for additional information.

• Always presume that any overhead power line is an energized line unless and until the person(s) owning

the line and/or the electrical utility authorities indicate that it is not an energized line and it has been visibly

grounded.

• Before operating any equipment near any power line make sure the line has been de-energized and visibly

grounded at the point of work.

• Electrocution can occur without touching an electrical power line. Electricity, depending on the magnitude,

can jump or become induced into equipment or conductive materials that come in close proximity to, but do

not touch a power line. High wind, lightning, wet ground and other environmental conditions will increase the

possibility of electrocution and require additional consideration.

• Transmitter towers can induce the equipment or materials being handled with an electrical charge. Before

working or operating equipment near transmitter towers, make sure the transmitter is de-energized.

• Select the location where the span/drive unit will be assembled to ensure that neither the irrigation machine,

or the equipment used during the assembly process, will violate the minimum clearance guidelines.

• Never operate equipment or allow the load, ropes or tag lines within 10 ft (3.05 m) of any power line rated 50

kV or lower whether it is energized or not. For lines rated over 50 kVs, the minimum clearance shall be 10 ft

(3.05 m) plus 0.4 inch (1.1 cm) for each kV over 50 kVs.

• Never assemble, tow, transport or allow irrigation machine components underneath or within 10 ft (3.05 m)

of any power line rated 50 kV or lower whether it is energized or not. For lines rated over 50 kV, the minimum

clearance shall be 10 ft (3.05 m) plus 0.4 inch (1.1 cm) for each kV over 50 kVs. Overhang support angles,

cables and spinner drive components regularly extend 10 ft to 12 ft (3.1 m to 3.7 m) above the irrigation

pipeline (span).

• Use barricades to identify areas where interference with overhead power lines could occur. Keep the assem-

bly, towing or transporting of irrigation machine components and the operation of equipment including load,

ropes or tag lines away from any power line, in the distances described above, whether the line is energized

or not.

• Always designate a person to observe clearance between the power line and all equipment being operated

or moved in order to give timely warning for all operations to STOP if the minimum clearance is violated.

Safety

Minimal Lockout / Tagout Procedure

The following procedure establishes the minimum requirements for the lockout of energy isolating devices

whenever maintenance or servicing is done on machines or equipment. It is used to ensure that the machine

or equipment is stopped, isolated from all potentially hazardous energy sources and locked out before person-

nel perform any servicing or maintenance where the unexpectedly energized or start-up of the machine or

equipment or release of stored energy could cause injury. All personnel, upon observing a machine or piece of

equipment which is locked out to perform servicing or maintenance shall not attempt to start, energize, or use

that machine or equipment.

When the energy isolating devices are not lockable, tagout should be used and affected personnel must wear

full personal protection.

Refer to U.S. Occupational Safety & Health Administration (OSHA) Regulations (Standards - 29 CFR) Typical

minimal lockout procedures - 1910.147 App A, or applicable national, state or local regulations, for additional

information.

Sequence of Lockout

1. Notify all affected personnel that servicing or maintenance is required on a machine or equipment and that

the machine or equipment must be shut down and locked out to perform the servicing or maintenance.

2. The authorized personnel shall identify the type and magnitude of the energy that the machine or equip-

ment utilizes, shall understand the hazards of the energy, and shall know the methods to control the energy.

3. If the machine or equipment is operating, shut it down by the normal stopping procedure (depress the stop

button, open switch, close valve, etc.).

4. De-activate the energy isolating device(s) so that the machine or equipment is isolated from the energy

source(s).

5. Lock out the energy isolating device(s) with assigned individual lock(s).

6. Stored or residual energy (such as that in capacitors, springs, elevated machine members, rotating ﬂy-

wheels, hydraulic systems, and air, gas, steam, or water pressure, etc.) must be dissipated or restrained by

methods such as grounding, repositioning, blocking, bleeding down, etc.

7. Ensure that the equipment is disconnected from the energy source(s) by ﬁrst checking that no personnel

are exposed, then verify the isolation of the equipment by operating the push button or other normal operat-

ing control(s) or by testing to make certain the equipment will not operate.

!CAUTION

•RETURN OPERATING CONTROL(S) TO NEUTRAL OR “OFF” POSITION AFTER VERIFYING THE

ISOLATION OF THE EQUIPMENT.

8. The machine or equipment is now locked out.

!DANGER

•WHEN PERSONNEL WILL BE EXPOSED TO CIRCUIT ELEMENTS AND ELECTRICAL PARTS, A

QUALIFIED PERSON MUST USE TEST EQUIPMENT TO VERIFY THAT THE CIRCUIT ELEMENTS

AND EQUIPMENT PARTS OF THE EQUIPMENT ARE DE-ENERGIZED.

Restoring Equipment to Service

When the servicing or maintenance is completed and the machine or equipment is ready to return to normal

operating condition, the following steps shall be taken:

1. Check the machine or equipment and the immediate area around the machine to ensure that non-essential

items are removed and that the machine or equipment components are operationally intact.

2. Check the work area to ensure that all personnel are safely positioned or removed from the area.

3. Verify that the controls are in neutral.

4. Remove the lockout devices and re-energize the machine or equipment.

5. Notify affected personnel that the servicing or maintenance is completed and the machine or equipment is

ready to be used.

Inhaltsverzeichnis

Andere Valley Bewässerungssystem Handbücher

Valley

Valley Bender160 Bedienungsanleitung

Beliebte Bewässerungssystem Handbücher anderer Marken

Hunter

Hunter Institutional Series Bedienungsanleitung

Cellfast

Cellfast 52-305 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL A Bedienungsanleitung

Oral Care Technologies

Oral Care Technologies Hydro Floss Bedienungsanleitung

Reliable

Reliable F1-300 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Gem F892 Bedienungsanleitung

Netafim

Netafim NETBEAT Bedienungsanleitung

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Bedienungsanleitung

Tyco

Tyco CC3 Bedienungsanleitung

Reliable

Reliable F4FR Bedienungsanleitung

OpenSprinkler

OpenSprinkler OSPi Bedienungsanleitung

EINHELL

EINHELL GE-WW 5537 E Bedienungsanleitung

Reliable

Reliable F1FR42 Series Bedienungsanleitung

Reliable

Reliable F1FR-300 Bedienungsanleitung

Toro

Toro 730 Series Kurzanleitung

Eden

Eden 97063-EDAMZ Bedienungsanleitung

Tyco

Tyco TY-L Series Bedienungsanleitung