Valor Portrait Senator Installations- und Betriebshandbuch

4001648-01

Note: This kit must be installed or serviced by a qualied installer, service agency or

gas supplier. These instructions are to be used in conjunction with the main installation

instructions for the above listed heater models.

WARNING: If the information in these instructions is not followed exactly, a re or explosion

may result causing property damage, personal injury or loss of life.

FOR INSTALLATION WITH A VALOR 530 ENGINE, READ THE

FOLLOWING INSTRUCTIONS.

FOR 530 ENGINE CONFIGURATIONS AND VENTING,

REFER TO MAIN INSTALLATION BOOKLET SUPPLIED WITH THE

ENGINE.

#563SCB

Senator Cast Front

CSA approved for use only with

Valor 530

Model Heaters

INSTALLATION BOOKLET

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Portrait

Casting Tolerances

Due to the nature of cast iron, dimensional consistency may vary from one unit to the next and some variation

in surface nish and atness is to be expected. We have done our best to control and make allowance for this;

however some variation is inevitable.

Kit Contents

Cast front

Mounting

Brackets

Plinth

Rear Base

Support

Framing plate

ZC Stand-offs Top Bafe

Insulation

pad

INSTALLATION WITH 530 ENGINE

The Valor model 530 heater with the 563SCB Senator Front comes ready for installation as a zero clearance unit

into combustible type framing, without need for a separate zero clearance kit. The 530 without the standard zero

clearance stand-off spacers may also be installed into existing solid-fuel burning replaces provided space and local

codes permit.

Hearth Requirements

A 7/8” high plinth is supplied to raise the heater and ensure a base at the proper height for the cast front to sit on

regardless of oor nish height. If not using the plinth supplied, you MUST make allowance for oor nish and raise

(shim) the heater up so the bottom of the heater sits at the nished oor/hearth height, otherwise, the cast front will

not sit at the proper height.

Anon-combustible hearth is not required in front of this appliance.

Floor & Mantel Requirements

The 530 heater is approved for installation directly on any combustible material other than soft ooring material

such as carpet or vinyl.

The 563SCB Senator Front may be installed with combustible mantels provided clearances are maintained as

indicated in the Dimensions and Clearances, and Framing diagrams below and on the following page. Be aware that

although safe, some combustible materials and nishes at the listed clearances may, over time, discolor, warp, or

show cracks. Care should be taken when choosing materials—consult your replace dealer.

Dimensions & Clearances

Top

Outlet

7/8”High

Raised Plinth

5”

‘X’ 11”

8”

2”

1”

Insul.

21-5/8”

25-1/4”

37”(as 539 front)

37-7/8”(includes plinth)

5-1/2”

‘Y’

Mantel

ZC Stand-offs

Framing

Plate

26-1/8”

27-1/2”

26”

Framing plate

31-1/4”

7/8”

26-1/4”

20”

11” 9”

1”max.

1/2”min.

5”

Plinth

(optional) 26”

Mantel

leg or

sidewall

2”

6-5/8”

dia.

3”

Mantel

clearance “X”

Mantel

clearance “Y”

1” - 6” 33”

7” - 8” 34”

9” - 12” 38”

12” + 38” + 1” for

every inch

beyond 12”

FRAMING

The 563SCB Senator Front comes

supplied with a framing plate for zero

clearance applications. The framing

plate is painted black and may be left

exposed beyond the perimeter of the

cast iron front or may be covered with

non-combustible material if desirable.

A non-combustible hearth is not

necessary in front of this appliance.

The appliance is approved to install

directly on wood sub-ooring.

Any framing construction must be

clear of stand-offs.

Be aware that the area of 7½” x

26¼” (19 cm x 67 cm) immediately

above the framing plate must be

constructed with non-combustible

materials as shown in gures.

•

non-combustible finish

and backing required

Tighten screws after wall finish

to pull brackets tight

Cast Front

Framing Plate

Cover brackets

Cover Framing Plate

up to holes

Wall Finish

(note: any material

covering framing plate

or within 7-1/2”at top

must be non-combust.

non-combustible finish

& backing required

Mount Brackets to Heater

Install Framing Plate

flush with framing or

butt drywall to plate

and run finish over plate

Raised plinth

not shown

Framing Plate

Header Location for

Rear Vent Installations

Brackets Screwed tight

to Plate

Wall Finish

Combustible or

non-combustible

Framing Plate Protudes

by desired wall finish

thickness

Bend Tabs out

for desired wall

finish thickness

Tab Detail

Cast Front

Covers Brackets

Non-Combust.

Mat’l only

Above

Framing Plate

Raised plinth

not shown

Framing plate exposed

Framing plate covered

Wall Finish

If using Top Vent, note

proximity of pipe to

header (if any).See

plan view on page 3.

Maintain clearance

to vent as listed in

heater manual.

38”

to underside

of cavity

(includes

plinth;

reduct by

7/8”if not

using plinth)

7-1/2” minimum

This part of

wall must be

non-combustible

(cement board

or similar)

Minimum 11”

26-1/4”

Top of finished

hearth or floor

FRAMING

INSTALLATION

Fit the top bafe under the top panel of the

appliance case. Secure with 2 thread forming

screws.

Fit the stand-off spacers. The stand-off spacers

for these installations are supplied at. These

spacers are left and right handed.

! Warning: Failure to install the stand-off

spacers may result in a re hazard.

Remove the 2 screws near each of the rear

top corners of the appliance and the 2 screws

near the rear top of each side.

Bend the spacers as shown.

Screw the spacers to the rear of the appliance

using the screws just removed.

Bend the side wings of the spacers to align

the 2 holes in each spacer with those in the

appliance sides. Secure the spacers using the

screws just removed.

Mount the framing plate to the appliance.

Secure the framing

plate and brackets

to the sides of the

appliance case with

4 thread cutting

screws supplied.

Screw from the

outside through the

access holes in the

framing plate.

Note: There are

alternate methods

of nishing around

the framing

plate—either

leaving it exposed

or recessing it and

covering it up with

the wall nish. See

page 4.

Install plinth and rear base support below

rebox (optional).

The purpose of the plinth is to allow the

appliance to be placed on a rough suboor,

such as plywood, without regard for the

additional thickness of oor nishes as the

appliance bottom must otherwise be placed at

the nished hearth height or the front trims will

not t on the appliance properly.

Detach the burner module from the

4”

(102 mm)

total

insulation

Cut out insulation

for top vent installation

Pull forward to expose

minimum width of 5”

appliance by removing its 11 screws.

Fit the rear base support under the rear of the

appliance attaching it to the appliance back

panel with 2 x 3/8” thread cutting (pointed

end) screws.

Fit the front plinth under the appliance front

with 2 thread forming screws.

Install top insulation layer. For top vent outlet

appliances, cut out a circle at the center of the

insulation layer for the vent collar. Place the

insulation layer on top of the appliance case

inboard of the stand-off spacers.

Warning: Failure to install the insulation layer

may cause a re

hazard and voids

warranty.

If the hooks have

been shipped loose

with the cast front, x

them to the front at

its top corners.

Hook the cast front on the appliance through slots on

each side of the heat duct.

Place the cast top on the cast front.

CLEANING

It will be necessary to clean the glass periodically.

During startup, condensation, which is normal, forms

on the inside of the glass and causes dust, lint or other

particles to cling to the glass surface.

Initially, paint, while curing, may deposit a slight lm on

the glass. We therefore recommend that, during the rst

few weeks of use, the glass be cleaned 2 or 3 times with

non-abrasive common household cleaners and warm

water.

Ammonia based cleaners should not be used.

Subsequently the glass should be cleaned 2 or 3 times a

season depending on the circumstances.

Do not clean the glass while it is hot.

Dust can be brushed from the ceramic fuel effects and

rebox walls after removing the front unit and opening

the window.

Removing the front unit

Remove cast top place aside, unhook the cast front.

Lift it up by holding the decorative grille. DO NOT lift by

holding the top.

Opening the window

Always securely replace the window before

lighting.

The inside of the window can be cleaned by pulling

forward and rotating the 2 clamping bars at the top

corners of the window and swinging the window part way

down as shown.

! Be careful not to distort or damage the spring-

loaded bolts—don’t swing the window down more

than is necessary!

To completely remove the window, also unscrew the

2 spring-loaded bolts at the bottom of the window as

shown.

After retting the window, apply light hand pressure

against the window frame sides to bed-in the window

seal.

Dust can also be removed from the burner using a soft

brush after removing the ceramic fuel effects.

When cleaning, make sure that no particles are

brushed into the slots of the burner.

Always completely remove the window before

removing the ceramic fuel effects.

REPAIRS PARTS LIST

#Description Number Alternate no. Qty

1 Ashpan Door 4001588AH 4001588AH 1

2 Cast Fender 4001587AH 4001587AH 1

3 Lower Shield 4001726AH 4001726AH 1

4A Cast Column LH 4001583AH 4001583AH 1

4B Cast Column RH 4001584AH 4001584AH 1

5Upper Cast Front 4001586AH 4001586AH 1

6Upper Cast Panel 4001585AH 4001585AH 1

7 Top Casting 4001582AH 4001582AH 1

8Top Bafe 4001592AH 4001592AH 1

9Mounting Bracket and Screws 4001595 4001595 2

10 Rear Base Support 569079 340B236 1

11 Plinth 569059 350K967 1

12 Framing Plate 4000469 4000469 1

13 Heater Mounting Bracket 4000488 4000488 2

14 ZC Stand-off LH 569039 340B235 1

15 ZC Stand-off RH 569029 340B234 1

16 Insulation Layer 569049 620B987 1

17 Finial 4001589 4001589 2

Hardware Kit 4001209 4001209 1

Designed and Manufactured by / for

Miles Industries Ltd.

190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1

Tel. 604-984-3496 Fax 604-984-0246

www.valorreplaces.com

10 12

Note: Ce kit doit être installé ou réparé par un installateur qualié, une agence de service certiée

ou un fournisseur de gaz. Ces instructions doivent être utilisées conjointement avec les instructions

d’installation des modèles de foyers Valor indiqués ci-dessus.

MISE EN GARDE: Si les instructions fournies dans le présent manuel ne sont pas suivies à

la lettre, un feu ou une explosion pourraient résulter et causer des dommages matériels, des

blessures ou la mort.

POUR INSTALLATION AVEC LE FOYER VALOR 530, SUIVEZ LES

INSTRUCTIONS AUX PAGES SUIVANTES.

POUR LA CONFIGURATION ET L’ÉVACUATION DU FOYER VALOR

530, CONSULTEZ LE MANUEL D’INSTALLATION FOURNI AVEC LE

FOYER.

563SCB

Devanture de fonte Senator

homologuée par la CSA pour utilisation

exclusive avec les foyers Valor

530

GUIDE D’INSTALLATION

INSTALLATEUR : Laissez cette notice avec l’appareil.

CONSOMMATEUR : Conservez cette notice pour consultation ultérieure.

Portrait

Inhaltsverzeichnis

Sprachen:

Andere Valor Kamin im Innenbereich Handbücher

Valor

Valor Wonderfire BR419 Bedienungsanleitung

Valor

Valor Legend 736AN Bedienungsanleitung

Valor

Valor Legend G4 Series Betriebsanleitung

Valor

Valor Horizon 673EDN Bedienungsanleitung

Valor

Valor DIMENSION ELECTRIC Series Bedienungsanleitung

Valor

Valor Portrait 530ILN/ILP Betriebsanleitung

Valor

Valor 650JLN Bedienungsanleitung

Valor

Valor C1 Montageanleitung

Valor

Valor L2 1700KN Bedienungsanleitung

Valor

Valor Brava 347 Bedienungsanleitung

Valor

Valor MADRONA MF28JN Bedienungsanleitung

Valor

Valor 479MP Bedienungsanleitung

Valor

Valor LX2 2200KN Bedienungsanleitung

Valor

Valor 722AP Montageanleitung

Valor

Valor LEGEND G4 780JN (NG) Montageanleitung

Valor

Valor 347 Helmsley Bedienungsanleitung

Valor

Valor ALTON DIMENSION Bedienungsanleitung

Valor

Valor equinox 754 Bedienungsanleitung

Valor

Valor 2200JN Betriebsanleitung

Valor

Valor 530 Direct Vent Bedienungsanleitung

Valor

Valor STONEFIRE SF10BL Bedienungsanleitung

Valor

Valor 530SAN Montageanleitung

Valor

Valor COSYFLAME TURBOCHIM 528 Montageanleitung

Valor

Valor LEGEND G3.5 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch