Van Mechelen BTP-2002NP Bedienungsanleitung
I
IN
NS
ST
TA
AL
LL
LA
AT
TI
IO
ON
N
M
MA
AN
NU
UA
AL
L
Single Station Thermal Printer
zThis printer has been manufactured and branded for ORIENT Technologies
B.V. by Shandong New Beiyang Information Technology Co., Ltd.
zDesign and specifications are subject to change without notice. Ask your
supplier for technical specifications before purchase and/or use.
zWhenever in doubt about safety issues that might arise from using this product,
please contact the supplier immediately for assistance.
M
Mo
od
de
el
l:
:B
BT
TP
P-
-2
20
00
02
2N
NP
P
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
BTP-2002NP Installation manual
- 1 -
Declarations
Changes without notice
Information in this document is subject to change without notice. ORIENT Technologies bv
(hereinafter referred to as “ORIENT Technologies”) and SHANDONG NEW BEIYANG
INFORMATION TECHNOLOGY CO., LTD. (hereinafter referred to as “SNBC”) reserves the right
to improve products as new technology, components, software, and firmware become available.
If users need further data about this product or have any doubt about safety issues that might
arise from using it, please feel free to contact ORIENT Technologies, SNBC or your local agents.
Copyright
No part of this document may be reproduced or transmitted in any form or by any means,
electronic or mechanical, for any purpose without the express written permission of ORIENT
Technologies or SNBC.
Copyright © 2007 by SNBC
Printed in China
Version 1.1
Trademarks
Our registered trademarks are
Warnings and Cautions in this manual
Warning: Items shall be strictly followed to avoid damages to body and equipment.
Caution: Items with important information and prompts for operating the printer.
Certifications
The quality control system of SNBC has been approved of the following certification.
(DNV)ISO9001:2000
The environmental control system of SNBC has been approved of the following certification.
(DNV)ISO14001:2004
BTP-2002NP has been approved of the following certification.
WEEE directive 2002/96/EC
ORIENT Technologies bv is complying with all aspects of the European Union’s WEEE directive
2002/96/EC. All the customers and end-users can send the products that have reached the end
of their lifes and are to be recycled, to ORIENT Technologies bv. ORIENT Technologies bv will
take care of the recycling of these products in an environmentally responsible manner in
accordance with WEEE directive.
BTP-2002NP Installation manual
- 2 -
Contact us
In CHINA:
Address: No.169 Huoju Rd, Weihai, Shandong, China. 264209
Hot line: +86-631-5673777
Fax: +86-631-5673778
E-mail: sales@newbeiyang.com
Website: www.newbeiyang.com (via Contact button)
In EUROPE: ORIENT Technologies bv
Address: Meerheide 115, 5521 DX Eersel, The Netherlands
Hot line: +31-497-331080
Fax: +31-497-386430
Website: www.orient-technologies.com (via Contact button)
BTW BE 0415.638.961
Rek: 230-0026460-96
info@vanmechelen.be
www.vanmechelen.be
Patersstraat 106-108
2300 Turnhout
Tel:014/42.55.99
Fax: 014/42.32.64
BTP-2002NP Installation manual
- 1 -
CONTENT
GENERAL SAFETY INFORMATION.....................................................2
1PARTS IDENTIFICATIONS ............................................................3
2SETTING UP THE PRINTER .........................................................5
2.1 Unpacking ..............................................................................5
2.2 Connecting the Cables..........................................................5
2.2.1 Interface Connector.............................................................6
2.2.2 Cash Drawer Connector......................................................8
2.3 Loading the Paper Roll .........................................................8
3SWITCH, BUTTON AND LED......................................................11
3.1 Power Switch .......................................................................11
3.2 Feed Button..........................................................................11
3.3 LED........................................................................................11
4SELF-TEST...................................................................................12
5HEXADECIMAL DUMP................................................................12
6SPECIFICATIONS........................................................................13
6.1 General Specifications........................................................13
6.2 Auto Cutter Specifications .................................................14
6.3 Interface................................................................................14
6.4 Electric Parameters of the Power Supply.........................14
6.5 Environmental Conditions..................................................14
6.6 Reliability..............................................................................15
6.7 Black Mark Specifications..................................................15
6.8 Overall Dimension...............................................................16
7FEED BUTTON CONFIGURATION .............................................16
BTP-2002NP Installation manual
- 2 -
General Safety Information
Before installing and using the printer, please read the following items carefully.
Safety Labels
Don’t touch the cutter and tear bar of printer.
The print head is a thermal element and it is at high temperature during printing or
just after operation, therefore please do not touch it and its peripherals for safety
reasons.
The thermal head is an ESD-sensitive device. To prevent damage, do not touch
either its printing part or connecting parts.
Caution
Install the printer on a flat and stable place.
Reserve adequate space around the printer so that convenient operation and maintenance
can be performed.
Keep the printer away from water source.
Do not use or store the printer in a place exposed to heat of fire, moisture, serious pollution
and direct sunlight.
Do not place the printer on a place exposed to vibration or impact.
No dew condensation is allowed to the printer. In case of such condensation, do not turn on
the power until the condensation has completely gone away.
Connect the AC adapter to an appropriate grounded mains outlet. Avoid sharing the mains
outlet with large power motors and other devices that may cause the fluctuation in voltage.
Disconnect the AC adapter when the printer is not used for a long time.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Don’t spill water or other materials on the printer. If this happens, turn off the power
immediately.
Do not allow the printer to start printing when there is no printer paper installed, otherwise the
print head and platen roller might be damaged.
To ensure quality print and normal lifetime, use recommended or good quality printer paper.
Shut down the printer when connecting or disconnecting interfaces connectors to avoid
damage to the control board.
Set the print darkness to a lower grade as long as the print quality is acceptable. This will help
to lengthen the print head life-time.
The printer should only be disassembled or repaired by a technician, who is certified by the
manufacturer or by ORIENT Technologies bv.
Keep this manual safe and at hand for ready reference.
BTP-2002NP Installation manual
- 3 -
Parts Identifications
1—Cutter cover
2—Tear bar
3—Printer top cover
4—Power LED
Indicating power status (ON/OFF).
5—Error LED
The red LED indicates basic
information about the status of the
printer. When the LED is off, the
printer is operating normally. A
flashing red LED means the printer
needs operator assistance (such as paper end).
6—Feed button
Under normal status (no error), press it to feed paper. To feed long
lengths of paper, press the key continuously.
7—Top cover latch
8—Power switch
Turning on/off the power for the printer.
“O”-power is turned off;
“—”-power is turned on.
9—Power connector
10－Cash drawer connector
11－Communication interface
BTP-2002NP Installation manual
- 4 -
12－Cutter acting blade
13－Printer platen
14－Cutter fixed blade
15－Paper end sensor
For continuous paper, this sensor is
used to detect whether the paper roll
has run out.
16－Paper-width-adjust module
There are 4 long slots at the base of paper holder, putting the
paper-width-adjust module in different slot will allow the printer to use
different width papers listed as follows:80±0.5 mm, 76±0.5 mm, 69.5±
0.5 mm, 57.5±0.5 mm. Removing the paper-width-adjust module will
allow a paper width 82.5 ±0.5mm.
Caution: Paper-width-adjust module is an indispensable part of printer
and should be kept safely.
17－Top cover position sensor
The sensor is used to detect whether the top cover is closed or not.
BTP-2002NP Installation manual
- 5 -
Setting UP the Printer
2.1 Unpacking
Your printer box should include these items. If any items are damaged or
missing, please contact your dealer for assistance.
2.2 Connecting the Cables
You can connect up the cables required for printing to the printer. They all
connect to the connector panel on the back printer, which is shown below:
Before connecting any of the cables, make sure that both the printer and the
computer are turned off.
BTP-2002NP Installation manual
- 6 -
2.2.1 Interface Connector
RS-232 serial interface (DB25F)
Pin Signal
name
Signal
direction Function
1 FG — Frame ground
2 TXD Output Transmit data
3 RXD Input Receive data
4 RTS Output Same as DTR signal
6
DSR Input This signal indicates whether the host computer can
receive data.
SPACE indicates that the host computer can receive
data, and MARK indicates that the host computer
cannot receive data.
When DTR/DSR control is selected, the printer
transmits data after confirming this signal (except when
transmitting data by DLE EOT, and GS a).
When XON/XOFF control is selected, the printer does
not check this signal.
7 SG — Signal ground
20 DTR Output 1) When DTR/DSR control is selected, this signal
indicates whether the printer is busy. SPACE
indicates that the printer is ready to receive data,
and MARK indicates that the printer is busy.
2) When XON/XOFF control is selected:
The signal acts the same as when DTR/DSR
control is selected.
BTP-2002NP Installation manual
- 7 -
Parallel interface
Pin Source Function Pin Source Function
1 H NStrobe 19 Signal Ground (nStrobe)
2 H Data 0
(Least Significant Bit) 20 Signal Ground (Data 1)
3 H Data 1 21 Signal Ground (Data 2)
4 H Data 2 22 Signal Ground (Data 3)
5 H Data 3 23 Signal Ground (Data 4)
6 H Data 4 24 Signal Ground (Data 5)
7 H Data 5 25 Signal Ground (Data 6)
8 H Data 6 26 Signal Ground (Data 7)
9 H Data 7
(Most Significant Bit) 27 Signal Ground (Data 8)
10 P NAck 28 Signal Ground
(PError, Select, and nAck)
11 P Busy 29 Signal Ground
(Busy and nFault)
12 P Perror 30
Signal Ground
(nAutoFd, nSelctIn, and
nInit)
13 P Select 31 H NInit
14 H nAutoFd 32 P NFault
15 Not defined 33 Not defined
16 Logic Gnd 34 Not defined
17 Chassis Gnd 35 Not defined
18 P Peripheral Logic High 36 H nSelectIn
Ethernet
Pin Number Signal Name Function
1 TX+ Output Data+
2 TX- Output Data -
3 RX+ Input Data+
4 NC
5 NC
6 RX- Input Data -
7 NC
8 NC
Inhaltsverzeichnis
Andere Van Mechelen Drucker Handbücher
