Vanderbilt CHSM2210 Bedienungsanleitung
CHSM2210/2211
Medium Camera Housing
Installation Guide
© Vanderbilt 2016
2
Data and design subject to change without notice. / Supply subject to availability.
© 2016 Copyright by Vanderbilt
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our
prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.
© Vanderbilt 2016
3
Contents
1Safety .......................................................................................................5
1.1 Target group..............................................................................................5
1.2 General safety precautions.......................................................................5
1.3 Meaning of the signal words .....................................................................6
1.4 Meaning of the hazard symbols................................................................6
2EU Directives...........................................................................................7
3Technical data .........................................................................................8
3.1 Specifications............................................................................................8
3.2 Mechanical dimensions.............................................................................9
3.3 Key to parts...............................................................................................9
4Scope of delivery ..................................................................................10
5Installation .............................................................................................11
5.1 Accessing the inside of the housing enclosure.......................................11
5.2 Fitting the power supply modules ...........................................................12
5.3 Cable entry into the camera housing ......................................................14
5.4 Fitting the camera and lens.....................................................................14
5.5 Mounting the camera housing assembly ................................................15
5.6 Connecting to the power supply..............................................................16
5.7 Adjusting the sunshield...........................................................................17
6Maintenance and service .....................................................................18
7Disposal .................................................................................................18
Safety
© Vanderbilt 2016
5
1 Safety
1.1 Target group
The instructions in this document are designed only for the following target group.
Target readers
Qualification
Activity
Condition of the
product
Installer
Technical training for
building or electrical
installations.
Installs the product,
individual components
of the product or
replacement parts.
Components of the
product are not yet
installed or need to be
replaced or modified.
1.2 General safety precautions
Read the general safety precautions before operating the device.
Follow all warnings and instructions marked on the device.
Keep this document for reference.
Always pass this document on together with the product.
Please also take into account any additional country-specific, local safety
standards or regulations concerning project planning, operation and disposal of
the product.
It is recommended that all possible work be carried out in a workshop prior to
final installation.
Liability claim
Do not connect the device if it is damaged or any parts are missing.
Do not make any changes or modifications to the device unless they are
expressly mentioned in this manual and have been approved by the
manufacturer.
Use only spare parts and accessories that have been approved by the
manufacturer.
Risk of failure due to incorrect installation
The fuse for the device and the fuse for the electrical system of the building must
be installed separately.
Risk of cable damage due to stress
Use only cable types that are approved for the environmental requirements.
The cable glands used must be appropriate for the cable diameter.
Safety
© Vanderbilt 2016
6
1.3 Meaning of the signal words
The severity of a hazard is indicated by the following written warning notices.
Signal word
Type of hazard
CAUTION
There is a risk of minor to medium injuries or damage to property
IMPORTANT
Malfunctioning may result
1.4 Meaning of the hazard symbols
The nature of the hazard is indicated by icons.
Warning of a hazard
EU Directives
© Vanderbilt 2016
7
2 EU Directives
The product complies with the requirements of the following EU directives. The EU
declaration of conformity is available from:
Vanderbilt
Clonshaugh Business and Technology Park
Clonshaugh
Dublin 17
Ireland
www.vanderbiltindustries.com
EU Directive 2004/108/EC on electromagnetic compatibility
Conformity with the European Directive 2004/108/EC is demonstrated by
compliance with the following standards:
Emitted interference:
EN 61000-3-2
EN 61000-3-3
EN 55022 Class B
Resistance to interference:
EN 50130-4
EU Directive 2006/95/EC “Low-Voltage Directive”
Compliance with the European Directive 2006/95/EC has been proven by testing
according to the following standard:
Safety:
EN 60950-1
Technical data
© Vanderbilt 2016
8
3 Technical data
3.1 Specifications
Nominal Voltage
CHSM2210: 110 –230 V AC, 50/60 Hz
CHSM2211: 12 –24 V AC, 50/60 Hz
Fuse Rating (Fuse F1)
CHSM2210: 2 A, 250 V AC, 5 x 20 Type (T), HBC
CHSM2211: 5 A, 250 V AC, 5 x 20 Type (T), HBC
Electrical Connections
Main supply connections via fused PCB mounted terminal blocks.
Use crimped ferrules when terminating cables.
6 way pillar terminal block available for user connections.
Cable Entry
1 x 20 mm Cable Gland (6 –12 mm diameter cable range)
2 x 16 mm Cable Glands (5 –10 mm diameter cable range)
Heater
Nominal: 7 W
max.: 25 W
PTC resistor heating element, thermostatically controlled.
Environmental
Operating Temperature
-20 to +60 °C
Ensure fitted equipment has suitable temperature range for the
application (e.g. maximum typical ambient operating temperature of
camera and lens. Ta = 40 °C).
Maximum internal dissipated power
30 W
Relative humidity
Up to 95 % non-condensing
Ingress Protection
IP66, BS EN 60529
Material
Toughened Glass Window
Housing body/Sunshield/Mounting rails: Aluminium extrusions
End caps: Die cast aluminium
Finish
Housing body: Polyester powder coat, RAL9006 White Aluminium
Sunshield: Polyester powder coat, RAL9006 White Aluminium
End caps: Polyester powder coat, RAL7016 Grey
Internal Dimensions (L x W x H)
300 x 85 x 85 mm
Weight
2.5 kg
Suitable Pan and Tilt Units
CDD2425, CDD2416-T, CDAP2316-T, CDAP2416-T
Suitable Brackets
CHBS2815, CDBS4540 + CAHA1040
Technical data
© Vanderbilt 2016
9
3.2 Mechanical dimensions
Fig. 1 Mechanical dimensions
1
246 mm
2
208 mm
3
3 mm
4
66 mm
5
133 mm
6
76 mm
7
125 mm
3.3 Key to parts
Fig. 2 Key to parts
1
Front End Cap
6
Cable Anchors
2
Housing Body
7
Terminal Board
3
Sunshield
8
Camera Mounting Slot
4
Rear End Cap
9
Demister Assembly
5
Cable Glands
10
Window
Scope of delivery
© Vanderbilt 2016
10
4 Scope of delivery
Camera housing assembly
Installation Guide
Camera fixing screw (¼” BSW x ½” hex hd.)
Camera fixing screw (¼” BSW x ¾” hex hd.)
Spacer block (1.6 mm thick)
Spacer block (3 mm thick)
2.5 mm (across flats) ALLEN Key, long reach
Camera plate insulator
Shoulder washer (to insulate screw from camera mounting plate)
NOTE
The complete assembly should be mounted and tested in the workshop prior to use on-site.
Accessories
Type
Designation
CAPD1210-C230
12 V DC 500 mA PSU 230 V AC input
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Vanderbilt Kamerazubehör Handbücher
