Vanguard Instruments VBT-75 S2 Bedienungsanleitung

VBT-75 S2

VACUUM BOTTLE TESTER

USER’S MANUAL

Vanguard Instruments Company, Inc.

1520 S. Hellman Ave.

Ontario, California 91761, USA

TEL: (909) 923-9390

FAX: (909) 923-9391

July 7, 2017

Revision 1

VBT-75 S2 USER’S MANUAL REV 1

SAFETY SUMMARY

FOLLOW EXACT OPERATING PROCEDURES

Any deviation from the procedures described in this operator’s manual may create one or more safety hazards,

damage the VBT-75 S2, or cause errors in the test results; Vanguard Instruments Co., Inc. assumes no liability for

unsafe or improper use of the VBT-75 S2. The following safety precautions must be observed during all phases of

test set up, test hookups, testing, and test-lead disconnects.

SAFETY WARNINGS AND CAUTIONS

This device shall be used only by trained operators. All circuit breakers under test shall be off line and fully

isolated.

SERVICE AND REPAIR

• Do not install substitute parts or perform any unauthorized modification to any VBT-75 S2 test unit.

• Repairs must be performed only by Vanguard Instruments Company factory personnel or by an authorized

repair service provider. Unauthorized modifications can cause safety hazards and will void the manufacturer’s

warranty.

EQUIPMENT RATINGS

IP Rating: The enclosure for the VBT-75 S2 has an IP rating of 32.

Pollution Degree: The VBT-75 S2 has a pollution rating of 2.

Operating Voltage: The VBT-75 S2 is rated for use with an operating voltage of 120V or 240V, auto-ranging ±10%

of selected voltage.

Power Cord: The VBT-75 S2 is supplied with a 16 AWG, 16A power cord with a NEMA 5-15P plug. Replacement

cable shall have the same or better rating and is available through the manufacturer.

VENTILATION REQUIREMENTS

The VBT-75 S2 must be operated with the enclosure lid open.

SAFETY SYMBOLS

Indicates that caution should be exercised

Indicates location of chassis ground terminal

CLEANING

To clean the VBT-75 S2:

• Disconnect all cables and turn the unit off.

• Use a soft, lint-free cloth to wipe all surfaces clean.

• Avoid getting moisture in openings and connectors.

• Don't use any cleaning products or compressed air.

REV 1 VBT-75 S2 USER’S MANUAL

TABLE OF CONTENTS

CONVENTIONS USED IN THIS DOCUMENT ....................................................................... 1

1.0 INTRODUCTION .................................................................................................................... 2

1.1 General Description and Features ................................................................................... 2

1.2 Technical Specifications ................................................................................................... 3

1.3 VBT-75 S2 Controls and Indicators .................................................................................. 4

2.0 CABLE CONNECTIONS .......................................................................................................... 6

3.0 OPERATING PROCEDURES ................................................................................................... 7

3.1 Set the Date and Time ..................................................................................................... 7

3.2 Changing the LCD Screen Contrast .................................................................................. 8

3.3 Performing a Test ............................................................................................................. 9

3.4 Updating Firmware ........................................................................................................ 11

LIST OF TABLES

Table 1. VBT-75 S2 Technical Specifications ................................................................................... 3

Table 2. Functional Descriptions of VBT-75 S2 Controls and Indicators ........................................ 5

LIST OF FIGURES

Figure 1. VBT-75 S2 Controls and Indicators .................................................................................. 4

Figure 2. VBT-75 S2 Connection Diagram ....................................................................................... 6

REV 1

This doc

•

A ke

•

Scre

• VBT-

Note

exa

• War

• Imp

BT-75 S2

ment uses

or switch

n and men

5 S2 LCD s

that the sel

ple above).

ing messag

RNING

rtant notes

OTE

UN TEST]

SETUP

CABLE VT

SER’S MAN

ONVEN

he followi

n the VBT-

names are

reen outpu

ected item

s are indic

rning mes

are indicat

te details

07/06

11:03:

G: 0V

UAL

IONS U

g conventi

5 S2 is indi

referenced

is shown a

n the scre

ted as:

age

d as:

ED IN T

ns:

ated as

as “SCREEN

n is enclose

IS DOC

and

/MENU NA

d in bracke

MENT

ITCH]

E”.

s ("[RUN TE

T]", in the

VBT-75 S2 USER’S MANUAL REV 1

1.0 INTRODUCTION

1.1 General Description and Features

The VBT-75 S2 is Vanguard's second generation microprocessor-based, portable, 75kV dc

vacuum bottle tester. This lightweight, portable tester is designed for testing circuit-breaker

vacuum bottles in the field and at the shop.

Test voltages can be selected from 10 kV dc to 75 kV dc in 5 kV steps. The high-voltage test time

can be set from 5 seconds to 2 minutes. The test voltage is raised to the selected voltage and

held for the test time duration. The test voltage and leakage current are displayed on the LCD

during testing. After the test time duration has elapsed and the leakage current did not pass the

pre-set value of 100 µA, 200 µA, or 300 µA, the test voltage is returned to zero and a "Pass"

message is displayed. If a flash-over condition occurs, such as bottle failure, the test voltage is

immediately turned off, a “Failure” message is displayed on the LCD screen, and the “TEST FAIL”

LED light on the unit is also illuminated.

The presence of high voltage is indicated by an audible tone and an illuminated “HIGH

VOLTAGE” LED light. For additional operator safety, an “ARM” switch must be held down during

testing.

The VBT-75 S2 features a back-lit LCD screen (20 characters by 4 lines) that is viewable in both

bright sunlight and low-light levels. A turn-and-press knob is used to control the unit. The VBT-

75 S2's firmware can be updated in the field via the unit's built-in USB Flash drive port.

The VBT-75 S2 is furnished with a 10-foot test cable that is terminated with a quick-disconnect

test clip. A transportation case is also included.

REV 1

1.2

PHY

BT-75 S2

echnical

ICAL SPECI

INP

OUTPU

PUT RIPPLE

DISCH

FIRMWAR

ENV

HUMI

ALTIT

SHIP

The

tem

SER’S MAN

pecificati

Table

TYPE

ICATION

T POWER

VOLTAGE

RGE TIME

DISPLAY

CONTROL

ICATOR

UPDATE

RONMENT

ITY (MAX)

DE (MAX)

CABLES

ING CASE

ARRANTY

bove specif

erature of

UAL

1. VBT-75 S

ortable 75 kV

imensions: 1

eight: 10 lbs

0 – 240 Vac,

0kV – 75 kV

% max

aximum disc

ack-lit LCD (

iewable in bri

ingle turn-an

ailure Indica

00 μA, or 300

igh Voltage I

irmware can b

terface

perating: -10˚

torage: -30˚

0% RH @ 40˚

000m (6562 f

ne 10-foot (3.

eturn cable, o

hipping case

ne year on p

ications are

5°C (77°F).

Technical

vacuum bottle

7”W x 10.5”H

. (4.53 Kg)

A, 50/60 Hz

c in 5 kV step

arge time for i

0 characters x

ht sunlight an

-press knob

: LED illum

μA (program

ndicator: LE

updated in t

to 50˚ C (15˚

to 70˚ C (-22˚

C (104˚ F) no

) to fully safet

5m) high-volt

e ground cabl

s included

rts and labor

valid at no

Specificatio

pecificatio

tester

6.5” D (42.7

; accuracy: 1.

nternal high v

4 lines);

d lo

-light lev

nates when te

able)

illuminates w

e field via the

o +122˚ F);

to +158˚ F)

n-condensing

specification

ge cable, one

e, one power

inal opera

s may cha

cm x 26.9 cm

ltage is 3 sec

st current exc

en high volta

unit's built-in

10-foot (3.05

ord

ing voltage

ge without

16.5 cm)

nds

eds 100 μA,

e is present

SB Flash driv

) high voltag

nd at a

prior notice

VBT-75 S2 USER’S MANUAL REV 1

1.3 VBT-75 S2 Controls and Indicators

The VBT-75 S2’s controls and indicators are shown in Figure 1 below. A leader line with an index

number points to each control and indicator, which is cross-referenced to a functional

description in Table 2. The table describes the function of each item on the control panel. The

purpose of the controls and indicators may seem obvious, but users should become familiar

with them before using the VBT-75 S2. Accidental misuse of the controls will usually cause no

serious harm. Users should also be familiar with the safety summary found on the front page of

this User’s Manual.

Figure 1. VBT-75 S2 Controls and Indicators

REV 1 VBT-75 S2 USER’S MANUAL

Table 2. Functional Descriptions of VBT-75 S2 Controls and Indicators

Item

Number Panel Markings Functional Description

1 HIGH VOLTAGE High voltage cable connector

2 USB MEM USB flash drive interface for firmware updates

3 Back-lit LCD screen (4 lines x 20 characters).

Viewable in bright sunlight and low-light levels.

120/240 Vac, 2A,

50-60 Hz

F3AL 250V

Input power connector with built-in fuse holder and power switch

5 GROUND VBT ground stud. Connect ground stud to substation ground using the provided

cable.

6 TEST FAILED Test failure indicator. This indicator turns on if the test current exceeds the

present current threshold (100, 200, or 300 μA).

7 PUSH TO

"ARM"

Arm switch; press and hold during testing.

8 CHANGE VBT turn-and-press control knob.

9 HIGH VOLTAGE

ENABLED

This indicator turns on when high test voltage is present at the test leads.

10 GROUND High voltage return cable connector

2.0

The VBT

voltage

to the va

WARNIN

ABLE C

75 S2 come

eturn cable

cuum bottl

• To pr

conn

• The c

• The v

NNEC

s furnished

Both cable

being test

tect the V

ct the unit'

rcuit break

cuum bottl

Fig

IONS

with one 10

are termin

d. A typical

T-75 S2 aga

ground st

r must be

e under tes

re 2. VBT-7

-foot (3.05

ated with a

cable conn

inst static d

d to the su

ff-line and

should be

S2 Connec

VBT-75

) high volt

ligator cla

ction is sh

scharge in t

station gro

ompletely i

n the OPEN

ion Diagra

S2 USER’S

ge cable an

ps that are

wn in Figur

he substati

nd.

olated.

position.

ANUAL

one 10-fo

used to con

2 below.

n, always

EV 1

ect

REV 1 VBT-75 S2 USER’S MANUAL

3.0 OPERATING PROCEDURES

3.1 Set the Date and Time

Follow the steps below to set the date and time for the VBT-75 S2's internal clock:

a. Start from the "START-UP" menu:

Turn the [CONTROL KNOB] until the SETUP option is enclosed in brackets as shown

below:

Press the [CONTROL KNOB].

b. The following screen will be displayed:

The SetTime option should be enclosed in brackets. Press the [CONTROL KNOB].

c. The following screen will be displayed:

Turn the [CONTROL KNOB] to select the first digit of the month and then press the

[CONTROL KNOB]. The cursor will move over to the second digit of the month.

Continue this process to enter the date and time. When you press the [CONTROL

KNOB] for the last time to set the second digit of the current minute, the date and

time will be set and you will be returned to the "START-UP" menu.

ENTER

MM-DD-YY HH:MM:SS

[SetTime ] LANGUAGE

LCD CONT EXIT

CABLE VTG: 0V

RUN TEST 07/06/17

[ SETUP ] 11:03:05

CABLE VTG: 0V

[RUN TEST] 07/06/17

SETUP 11:03:05

CABLE VTG: 0V

Inhaltsverzeichnis

Andere Vanguard Instruments Prüfgeräte Handbücher

Vanguard Instruments

Vanguard Instruments EZCT S2A Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments RFD-200 2 Series Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments VBT-75 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments VBT-75P Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments EZCT-2000C Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments EZCT-2000A Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments EZCT Handbuch

Vanguard Instruments

Vanguard Instruments VBT-75P S2 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments EZCT Gebrauchs- und Pflegehandbuch

Vanguard Instruments

Vanguard Instruments MCCB-500 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments CVT-765 Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments EZCT Bedienungsanleitung

Vanguard Instruments

Vanguard Instruments EZCT S2 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung