Vantron TMO Series Bedienungsanleitung

Vantron | Embedded in your success, Embedded in your better life

World-leading provider of embedded/IoT products and solutions

TMO series | Quick Installation Guide www.vantrontech.com

Vantron TMO Series Open-frame Touchscreen Monitors

Quick Installation Guide

Version: 1.3

General Safety Instructions

For your safety and prevention of damage to the Product, please read and observe carefully the following safety instructions prior to installation and operation. Keep this guide well

for future reference.

°Do not disassemble or otherwise modify the Product. Such action may cause heat generation, ignition, electronic shock, or other damages including human injury, and may void

your warranty.

°Keep away from heat source, such as heater, heat dissipater, or engine casing.

°Do not insert foreign materials into the openings of the Product as it may cause the Product to malfunction or burn out.

°Use only the adapter and power cord that are approved for use with this Product. Otherwise, it may cause fire or explosion.

°Be sure that nothing rests on the power cable and that the cable is located at a place without risk of trips.

°Cut off the power before inspection of the Product to avoid human injury or product damage.

°It is recommended to avoid leaving static images on the screen for extended periods of time, as this may lead to temporary image retention or "burn-in". For best practices, you

are advised to use screen savers or power-saving settings while not operating the device for an extended period.

ESD Precautions

While setting up an electronic system or handling electronic components, certain precautions and proper handling procedures should be followed to prevent ESD-induced failures.

Careless handling of ESDS components can degrade their reliability and life expectancy.

Electrostatic discharge (ESD) events can harm electronic components inside the Product. Under certain conditions, ESD may build up on your body or an object, such as a peripheral,

and then discharge into another object, such as the Product. To prevent ESD damage, you should discharge static electricity from your body before you interact with any of the

Product’s internal electronic components.

You can protect against ESD and discharge static electricity from your body by touching a metal grounded before you interact with anything electronic component on the Product.

When connecting a peripheral to the Product, you should always ground both yourself and the peripheral before connecting it to the Product. In addition, as you open the Product for

maintenance, periodically touch a metal-grounded object to remove any static charge your body may have accumulated.

Disclaimer

While all information contained herein has been carefully checked to assure its accuracy in technical details and typography, Vantron does not assume any responsibility resulting

from any error or features of this manual, nor from improper uses of this manual or the software.

It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the

Product may be changed without notice.

Please refer to the user manual of this series for more information on safety cautions and regulatory compliance statements.

Vantron Technology, Inc.

Address: 48434 Milmont Drive, Fremont, CA 94538

Tel: (650) 422-3128

Email: [email protected]

Vantron | Embedded in your success, Embedded in your better life

World-leading provider of embedded/IoT products and solutions

TMO series | Quick Installation Guide www.vantrontech.com

1. COMPONENT CHECKLIST

Check if all components are available:

•Touchscreen monitor

•Side mounting brackets

•Power adapter & power cable (not applicable to TMO07-DV & TMO101-DV)

•Touch USB cable

•HDMI cable & VGA cable

•DP cable (Optional, applicable only to TMO215, TMO238 & TMO270)

Note: Actual accessories might vary slightly from the list above as the customer

order might differ from the standard configuration options.

2. INSTALL THE TOUCHSCREEN MONITOR

2.1 Side mounting

Use the mounting brackets and screws to install the touchscreen monitor to the

desired place, and secure the screws.

Drawing for illustration only. The number of the brackets will depend on the

product model.

Screw specifications:

•M3 screws

•Thread depth: 6mm

2.2 VESA mounting

Vantron offers two VESA patterns on the back of the touchscreen monitor: 75mm

x 75mm and 100mm x 100mm.

Drawing for illustration only. The VESA pattern on TMO101 is 75mm x 75mm.

Screw specifications:

•M4 screws

•Thread depth: 8mm

3. CONNECT THE CABLES

1. Connect the display interface of the touchscreen monitor and the video/image

source with the HDMI/VGA/DP cable;

2. Connect the USB port of the touchscreen monitor and the PC/master device

(e.g., Vantron IBOX3588) with the USB cable to enable the touch control;

3. Plug in the audio cable, if needed (only applicable to TMO156 & TMO190);

4. Connect a 12V DC power supply to the power jack of the device, and the

LED indicator will turn solid red and enter the sleep mode;

5. Wait about 2-3 seconds and the LED indicator will turn solid green if the

PC/master device connected to functions properly;

6. Press the OSD power button on the back of the monitor to power off the

device.

TMO07-DV and TMO101-DV only implement an HDMI interface and a USB

3.0, and are powered over the USB port when connected to the

PC/master device. They do not offer OSD control buttons or related

functions. Therefore, the above steps are not applicable to the models.

7. LED INDICATOR AND OSD CONTROL

The relationship between the power indicator and the touchscreen

monitor status is as follows:

Indicator status Touchscreen monitor status

OFF

Solid red

SLEEP

Solid green

Working

OSD control buttons function as follows (N/A to TMO07-DV & TMO101-DV):

Button OSD not displayed OSD displayed

Menu OSD menu

Enter the submenu of a selected

parameter

OSD Brightness submenu

(Increase brightness)

Increase value of selected parameter/

Move to next menu upwardly

Down

OSD Brightness submenu

(Decrease brightness)

Decrease value of selected parameter/

Move to next menu downwardly

Back NA Return to previous OSD menu

8. TROUBLESHOOTING

Please refer to the following solutions/suggestions in case you encounter a

trouble during use of the touchscreen monitor.

If the trouble is not covered here or if the trouble persists, please contact your

sales representative. Please note that the solutions/suggestions are intended

for models other than TMO07-DV & TMO101-DV. Should you have any trouble

with TMO07-DV and TMO101-DV, please contact your sales representative.

1. The touch screen does NOT respond when the device is powered on.

-Check if the DC power adaptor is properly connected and functions well.

2. The screen is dim.

-Use the OSD control buttons to adjust the brightness or contrast of the

display.

3. The touchscreen monitor does NOT wake up automatically and the indicator

is red.

-Tap the screen and wait for the monitor to respond. If it fails, press the

power button, or re-connect the power supply, and wait a few seconds till

the indicator turns green.

4. The image is NOT properly displayed.

-Adjust the resolution/timing mode of the PC/master device to be within the

allowable ranges specified for the touchscreen monitor. Or, adjust the

display parameters manually with the OSD control button

VGA

HDMI

Andere Handbücher für TMO Series

Andere Vantron Touch-Screen Handbücher

Vantron

Vantron TMC Series Bedienungsanleitung

Beliebte Touch-Screen Handbücher anderer Marken

Elecro Engineering

Elecro Engineering Poolsmart Plus Montageanleitung

Johnson Controls

Johnson Controls IQ4 HUB Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems ET2270L Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems ET1002L Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems 3201L Bedienungsanleitung

Duratec

Duratec S15 Bedienungsanleitung

Crestron

Crestron TPMC-3SM Bedienungsanleitung

Racelogic

Racelogic MFD Touch Bedienungsanleitung

J2 580 Benutzerhandbuch

HAI

HAI OmniTouch 10p Bedienungsanleitung

panel

panel PC PSR108-FM Series Bedienungsanleitung

Tipro

Tipro FREE+ Bedienungsanleitung

Systemline

Systemline Commander Bedienungsanleitung

Interactive Technologies

Interactive Technologies Insite Bedienungsanleitung

GVision

GVision Legacy Bedienungsanleitung

BeiJer

BeiJer T21C-C24 Bedienungsanleitung

Advantech

Advantech ITM-5117 Series Bedienungsanleitung

Edge

Edge CS Bedienungsanleitung