Varytec LED PAR 64 Bedienungsanleitung

Manual

LED PAR 64 floor 12x8W

RGBWAUV incl. remote

2 / 16

Table of contents

1. Safety instructions............................................................................................................................ 3

1.1. For safe and efficient operation............................................................................................... 3

2. Designated use ................................................................................................................................ 4

2.1. Overhead installation............................................................................................................... 5

3. Introduction....................................................................................................................................... 7

4. Connections ..................................................................................................................................... 7

4.1. Electrical connections.............................................................................................................. 7

4.2. DMX connections .................................................................................................................... 7

4.3. DMX connection with terminator.............................................................................................. 7

5. Control.............................................................................................................................................. 8

5.1. Structure of the menu.............................................................................................................. 8

5.2. IR remote................................................................................................................................. 9

6. DMX chart ...................................................................................................................................... 10

6.1. Mode 1 (1 channel)................................................................................................................ 10

6.2. Mode 2 (6 channels).............................................................................................................. 11

6.3. Mode 3 (7 channels).............................................................................................................. 11

6.4. Mode 4 (10 channels)............................................................................................................ 11

7. Technical data................................................................................................................................ 13

3 / 16

1. Safety instructions

This device is suitable for indoor use (not outdoors) only.

All modifications to the device will void the warranty.

Repairs are to carry out by skilled personnel only.

Use only fuses of the same type and original parts as spare parts.

Protect the unit from rain and humidity to avoid fire and electric shocks.

Make sure to unplug the power supply before opening the housing.

1.1.For safe and efficient operation

Be careful with heat and extreme temperature

Avoid exposing it to direct rays of the sun or near a heating appliance.

Not put it in a temperature bellow 32°F /0°C, or exceeding 104°F /40°C.

Keep away from humidity, water and dust

Do not place the set in a location with high humidity or lots of dust.

Containers with water should not be placed on the set.

Keep away from sources of hum and noise

Such as transformer motor, tuner, TV set and amplifier.

To avoid placing on un-stable location

Select a level and stable location to avoid vibration.

Do not use chemicals or volatile liquids for cleaning

Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.

If out of work, contact sales agency immediately

Any troubles arose, remove the power plug soon, and contact with an engineer for repairing, do not

open the cabinet by yourself, it might result a danger of electric shock.

Take care with the power cable

Never pull the power cable to remove the plug from the receptacle, be sure to hold the plug. When not

using the device for an extended period of time, be sure to disconnect the plug from the receptacle.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not

accept liability for any resulting defects or problems. Make sure the electrical connection is carried out

by qualified personnel. All electrical and mechanical connections have to be carried out according to

the European safety standards.

4 / 16

2. Designated use

This device was developed for professional use on stages, in discos, theatres etc. The device is only

approved for a connection up to 230V 50/60 Hz AC voltage and only for indoor use.

Regular breaks during operation increase the lifetime of your device.

Avoid convulsions or any form of forceful impact during the installation or the start-up of the device.

Make sure that the device is not exposed excessive heat, humidity or dust at the place of installation.

Take care that no cables are lying around. You would endanger your own safety and also the safety of

a third party.

It is not allowed to operate or store the device in an environment in which spray water, rain, humidity

or fog is expected. Humidity or very high atmospheric humidity could reduce the isolation of the device

and could cause deathly electric shocks. If you use fog devices the device has not be exposed to a

direct smoke jet. There has to be a safety distance of at least 0,5m between this device and the fog

machine. Make sure that the saturation of the fog has to enable a visibility of at least 10m.

The ambient temperature has to be between 0°C and +40°C. Avoid direct sunlight and close proximity

to heaters. You have also to attend it during the transport in closed motor vehicles.

Operate the device not during thunderstorms. Surge voltages could destroy the device. Unplug the

power supply during thunderstorms.

During the installation the use of the mounting bracket is obligatory.

Surrounding objects or surfaces should not be in contact with the device.

Make sure that during the installation and removal of the device the area below the place of

installation is basically cordoned off. This also applies to implementation of service.

The device has basically been protected by a suitable safety.

Make familiar yourself with the functions of the device before start-up. People without the experience

should not handle with the device. The most cause of functional disorder is inappropriate handling.

Do not use chemicals or volatile liquids for cleaning. Use a clean dry cloth to wipe off the dust, or a

wet soft cloth for stubborn dirt.

For transport use the original packing or designated accessory to avoid damages during the transport.

For reasons of safety unauthorized changes are forbidden.

A usage of the device which differs from usages which are described in this manual can cause

damages of the device. In that case the warranty expires. Additional you should notice that every

differed usage is related with dangers and can cause e.g. an electrical short, fire, electric shock or

crash.

5 / 16

2.1.Overhead installation

Danger of life!

You have to observe the regulations of BGV C1 (formerly VBG 70) and

EN60598-2-17 Installations are to carry out by skilled personnel only.

The suspension devices have to be build and measured so they can withstand for an hour the tenfold

of the payload without suffering a permanent detrimental deformation.

Basically installation has to be made by using a second separate suspension. This can be e.g. a

suitable net. The second suspension must be designed and attached so no part of the installation can

fall down in case of failure.

During construction, reconstruction and deconstruction unnecessary stay in the range of moving

areas, on lightning bridges, under elevated work stations or any other danger zones is forbidden.

The operator is obliged to following safety-related and mechanical facilities:

- Before the first start-up or after critical changes before restarting it has to be checked by an

expert.

- Review in the frame of the inspection test at least all four years by an expert. .

- Review by a qualified person at least once a year.

How to carry out the overhead installation:

In tidal fall you should install the device out of the lounge area of people

IMPORTANT! Overhead installation requires a high level of experience. This includes knowledge of

calculating the payload, used installation material and safety inspections of the used material and the

projector whereas the required experience is not limited to this. Do not try to carry out installation

yourself under any circumstances if you are not qualified. Contact a professional installer. An

inappropriate installation can lead to injuries and/or damaged properties.

It is not allowed to install the device in the grip area of people.

If the device may hang from the ceiling or from high beams, the use of truss systems is mandatory.

The device may not be installed so it can swing freely in the room.

Please note: Crashing down items can cause serious injuries! Do not install the projector, if you doubt

the safety of a possible installation form!

Before installation make sure that the mounting surface has the ability to carry the tenfold point load of

the own weight of the device.

Mount the device with the mounting-bracket to your trussing system using an appropriate clamp.

During overhead installation the device must be always secured by a safety rope which is designed to

hold the twelvefold weight of device. Only safety ropes with quick-release safety fastener elements

may be used. Hang up the safety rope in the hole of the mounting bracket. Direct the rope over the

truss or an appropriate fastening point. Hang up the end in the fastening element and tie up the

locking nut. A safety rope once exposed to failing load or damaged may not be used furthermore.

6 / 16

The maximum drop exceed must not exceed 20cm.

A safety rope once exposed to failing load or damaged may not be used furthermore.

Adjust the desired inclination angle via the mounting bracket and tighten the screw.

7 / 16

3. Introduction

Thank you for buying the LED PAR 64 floor 12x8W RGBWAUV incl. remote. It is a powerful device.

For a successful installation and operation, please read this manual carefully.

4. Connections

4.1.Electrical connections

If you wish to change the power supply settings, see the chapter Appendix. Connect the fixture to the

mains with the enclosed power cable and plug. The earth has to be connected.

Cable (EU)

Cable (US)

International

Brown

Black

Live

Light blue

White

Neutral

Yellow/Green

Green

Earth

4.2.DMX connections

To make a DMX512 connection go ahead like it is described in the picture. Make sure that you use

shielded cable. 3pole or 5pole XLR cables are suitable.

Important! After the last device the line has to be terminated. In order to do this you have to solder a

120Ωresistor between the pins Data + and Data -. You can solder this end resistor on a 3pin or 5pin

XLR: Plug this adapter into the DMX output of the device.

4.3.DMX connection with terminator

Where the DMX cable has to run a long distance or the equipment is operated in an electrically noisy

environment like a disco for installations, we recommend using a DMX terminator. This prevents

corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR

connector with a 120 Ωresistor between pins 2 and 3, which is then plugged into the XLR output

socket of the last device in the series. Please look to the bottom drawings.

8 / 16

5. Control

Press MENU, to get into the menu. With UP/DOWN you can choose the required submenu. Confirm

with ENTER. Do your settings with UP/DOWN and confirm with ENTER. To step back press MENU

again.

5.1.Structure of the menu

Submenu 1

Submenu 2

Submenu 3

Function

Addr

A001 –A512

Setting the DMX address. If you

want to use the device in DMX

mode you have to be in this point of

menu.

Chnd

1Ch

Choose one of the DMX modes. If

you have chosen a DMX mode,

step back to the point of menu

Addr.

6Ch

7Ch

10Ch

Auto

Aut1

Sp-11 –Sp-9

St01 –St99

Choose one of the automatic

programs and set the speed of the

program and strobe. Slow-fast.

Aut2

CoLo

Co01 –Co51

St00 –St99

Choose a preset color and setting

the speed of the strobe. Slow-fast.

Stat

red

r000 –r255

St00 –St99

Dimmer red 0-100% and set the