Varytec Studio Par II CDM 150 Bedienungsanleitung
User’s manual
Studio Par II CDM
150
2 / 9
Table of content
1. Safety instructions........................................................................................................................... 3
2. Color frame retaining clip................................................................................................................ 4
3. Cleaning the reflector...................................................................................................................... 4
4. Installing the lamp........................................................................................................................... 5
5. Lens identification........................................................................................................................... 6
6. Changing CDM PAR lenses ........................................................................................................... 6
6.1. Installing a lens ...................................................................................................................... 6
6.2. Removing a lens .................................................................................................................... 7
7. Technical data................................................................................................................................. 8
3 / 9
1. Safety instructions
FOR SAFE AND EFFICIENT OPERATION
Be careful with heat and extreme temperatureAvoid exposing it
to direct rays of the sun or near a heating appliance.
Not put it in a temperature bellow 41°F /5°C, or exceeding 95°F /35°C.
Keep away from humidity, water and dust
Do not place the set in a location with high humidity or lots of dust.
Containers with water should not be placed on the set.
Keep away from sources of hum and noise
Such as transformer motor, tuner, TV set and amplifier.
To avoid placing on un-stable location
Select a level and stable location to avoid vibration.
Do not use chemicals or volatile liquids for cleaning
Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
If out of work, contact sales agency immediately
Any troubles arose, remove the power plug soon, and contact with an engineer for repairing,
do not open the cabinet by yourself, it might result a
danger of electric shock.
Take care with the power cable
Never pull the power cable to remove the plug from the receptacle, be sure
to hold the plug. When not using the player for an extended period of time
be sure to disconnect the plug from the receptacle.
4 / 9
2. Color frame retaining clip
The color frame holder is equipped with a spring-loaded retaining clip that prevents color frames and
accessories from falling out.
Warning! Hang the CDM PAR with the color frame retaining clip in the locked position
1. Release the retaining clip by pushing it sideways. The retaining clip opens.
2. Insert the color frame
3. press the retaining clip down until it locks.
Note: Use only color frames or top hats with 6.7 Inches inside diameter.
3. Cleaning the reflector
The following recommendations are offered when cleaning and inspecting lenses and reflectors.
Do not use glass and window cleaners on the reflector. Chemicals in these cleaners will ham the
reflective coatings.
Do not use paper towels or harsh materials to wipe the reflectors. These materials can scratch the
surface of the reflector.
Warning! Unplug the fixture before attempting to clean reflector.
1. Remove the lens so you can access the reflector from the front of the fixture. See removing a
lens in this manual.
2. Remove dust with a blast of oil free air, or wipe with a clean, soft, lint-free cotton cloth. If this is
sufficient to remove dust, go to step 5. otherwise continue with step 3.
3. Dampen a clean, soft, lint-free cotton cloth with a mild, soapy water solution and gently wipe
the reflector.
4. Remove any soapy water residue with a clean, soft, lint-free cotton cloth dampened with
water.
5. Reinstall a lens before using the fixture.
5 / 9
4. Installing the lamp
Always replace the lamp if it becomes damaged or deformed. Verify that the lamp you use is suitable
for the electronic power at your facility.
Caution! Operating lamps above or below their rated voltage reduces lamp life and can cause
premature lamp failure.
1. Disconnect the unit from power before installing the lamp.
Warning! Let lamp cool before changing.
2. Loosen the knurled bolt on the back of the lamp housing and pull the housing straight out from
the back of the fixture.
3. Remove the lamp from its box, holding it by the base.
Note: to avoid premature lamp failure, do not touch the lamp during installation, clean it
carefully with rubbing alcohol and a clean, lint-free cloth before operation.
4. Line up the flat sides of the lamp base with the brackets on either side of the socket. Figure 2
5. Push down on the lamp base until the lamp is firmly seated. Make sure that the lamp is fully
seated, with the bottom of the lamp heat sink flush to the lamp housing casting.
Caution: Improperly installed lamps cause premature lamp failure and socket
problems.
6. To reinstall the lamp housing, center it on the reflector and the bolt hole, then tighten the
knurled bolt to secure the lamp housing in place.
6 / 9
5. Lens identification
Lenses for the CDM PAR come in four versions. The type or beam spread can be identified by the
lens texture.
Very narrow spot Narrow Spot
Clear glass Stippie glass (slight diffuse texture)
15°round beam shape 19° round beam shape
Medium flood Wide flood
Fewer facets, sized 6 x 22mm Many facets, sized 6x12mm
21° x 34° oblong beam shape 30°x51° oblong beam shape
6. Changing CDM PAR lenses
Change lenses if they become cracked or badly scratched. Caution! Never operate the CDM PAR
without a lens in place.
6.1. Installing a lens
1. position the fixture with the front of the unit (the lens side) facing you, and tilted slightly.
(Figure 4)
2. Position the lens rotation ring with the spring clip at the top of the fixture, directlybelow the
retaining clip.
3. Hold the lens by the edge, and position it so the convex side faces the back of the fixture.
(Figure 3)
7 / 9
4. From the top of the fixture, slide the lens behind the lens catchers and position its base behind
the tabs on the bottom of the lens rotation ring.
5. gently push the top of the lens inward until it snaps behind the spring clip.
6.2. Removing a lens
Warning! Unplug the fixture before attempting to remove or install a lens.
1. Source CDM PAR lenses get hot while the unit is in operation. Let the fixture cool before
handling the lens.
2. Place the fixture on a flat, stable work surface. Do not install or remove lenses with the unit
hanging.
3. Position the lens rotation ring with the spring clip at the top of the unit, directly below the
retaining clip.
4. Tilt the front of the fixture down at least 45°
5. press the spring clip with your finger to release the lens (Figure 4)
6. allow the lens to drop forward from under the clip
7. when the lens drops, remove your finger, allowing the lens to slide forward until it rests on the
lens catchers (Fifure 5)
8. Carefully remove the lens from the fixture.
8 / 9
7. Technical data
Power supply
230-240V 50Hz
Power consumption
150W
Dimensions (L x W x H)
280 x 245 x 405
Weight
9,1kg
Fitting lamp
CDM-T lamps Base G12
Fuse
250V 4A
Max ambient temperature working
25°C
Max ambient temperature housing
70°C
Minimum distance
1m
9 / 9
Importeur:
B & K Braun GmbH
Industriestraße 1
D-76307 Karlsbad
www.bkbraun.com
Inhaltsverzeichnis
Andere Varytec Beleuchtungsausrüstung Handbücher
Varytec
Varytec GLC-1 Bedienungsanleitung
Varytec
Varytec Street Bar IP65 16x3W TW Bedienungsanleitung
Varytec
Varytec LED Ball RGBW 50cm 4x8W DMX Bedienungsanleitung
Varytec
Varytec BAT.PAR 8 RGBW Bedienungsanleitung
Varytec
Varytec FLATBEAM DUO 48x8W RGBW Bedienungsanleitung
Varytec
Varytec Derby Bedienungsanleitung
Varytec
Varytec RGBW IP65 Bedienungsanleitung
Varytec
Varytec Mini LED Strobe Bedienungsanleitung
Varytec
Varytec Hero Wash 340FX RGBW Zoom Bedienungsanleitung
Varytec
Varytec LED Laser 4 Bedienungsanleitung
Varytec
Varytec Hero Wash 300 FC Bedienungsanleitung
Varytec
Varytec LED Derby ST Bedienungsanleitung
Varytec
Varytec Strobe Xenon 3000DMX Bedienungsanleitung
Varytec
Varytec Sparkle 3 Bedienungsanleitung
Varytec
Varytec TouchWash Bedienungsanleitung
Varytec
Varytec LED Giga Bar 4 Bedienungsanleitung
Varytec
Varytec Hero Wash 300 TW Bedienungsanleitung
Varytec
Varytec Laser Moonstar MK II Bedienungsanleitung
Varytec
Varytec LED ROAD PAR 14 x 3W RGB 3in1 Bedienungsanleitung
Varytec
Varytec VR-260 Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
