Velleman CS5MXP Bedienungsanleitung

CS5MXP

METAL DETECTOR

METAALDETECTOR

DÉTECTEUR DE MÉTAL

DETECTOR DE METALES PROFESIONAL

PROFESSIONELLER METALLDETEKTOR

USER MANUAL

GEBRUIKERSHANDLEIDING

NOTICE D’EMPLOI

MANUAL DEL USUARIO

BEDIENUNGSANLEITUNG

CS5MXP VELLEMAN

- 2 -

ENGLISH

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm

the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to

a specialized company for recycling. This device should be returned to your distributor or to a local

recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into service. If the

device was damaged in transit, do not install or use it and contact your dealer.

1. Assemble and adjust for length (Twist surplus lead around stem)

2. Insert batteries

3. Set DISC 1 (top right) to ALL METAL (fully anticlockwise).

4. Set DISC 2 (bottom far right) to 5.

5. Set SENSITIVITY (top left) to 3 o'clock position.

6. Push BATT CHECK down and hold to indicate battery condition. Good batteries will be in the green area on

the meter. Release.

7. Set BOOST to NORMAL.

You are now in ALL METAL MOTION MODE.

You will find all metals within the search head range including iron and trash PROVIDING THE SEARCH HEAD IS

MOVING OVER THE TARGET (Not stationary).

To ignore these low value metals :

8. Adjust DISC 1 (top right) to position 5.

You are now in DISCRIMINATING MOTION MODE.

The other modes requires more detailed explanation acquired from reading the full instructions.

IF A PROBLEM IS ENCOUNTERED REFER TO FULL INSTRUCTIONS

CS5MXP VELLEMAN

- 3 -

Controls C-ScopeCS-5MXP

A Battery compartment

B Upper Stem & Handle Grips

C Din plug & Socket

D Stem connecting nut

E Cable

F Lower stem

G Search head fastner

H Power on / off & sensitivity

I Signalmeter

J All metal mode / Discrimination 1

K Boost Hi / Normal

L Pinpoint

M Battery check

N Disc 2 Select

O Discrimination 2

CS5MXP VELLEMAN

- 4 -

INTRODUCTION

The CS-5MXP combines 'turn on and go' technology with real depth to provide you with both simplicity in use yet

sophistication in performance.

IMPORTANT

These family of detectors are recognised as the finest detectors available. They are designed with lasting quality in

mind, high technology, and above all, value for money.

The only way to realise this value is to carefully study and understand this instruction manual. You will then be able

to obtain all of the advantages designed into your detector. It is also strongly recommended that you experiment

with the detector's operations in air, with various test samples, in order to learn to identify and understand the

detector's capabilities and responses.

Always remember that becoming a good metal detective is like becoming a good photographer or fisherman.

Although it is an advantage to buy the best equipment having bought it, patience and hours of practice are needed

to become proficient.

ASSEMBLY

Open the carton and remove the main housing assembly. Twist the plastic stem lock, located at the end of the

upper stem to allow the lower stem to be inserted. Adjust for length and rotate the lower stem to wrap the cable

around the stems and take p any slack. Allowing enough cable for free movement of the search head push the

cable into the cable slots to hold it firm. Turn the stem lock to fix it at the desired position.

BATTERIES

The CS-5MXP is powered by eight AA batteries (not supplied) available from garages, department stores, etc. or a

single 12V rechargeable pack from C-SCOPE. It is advisable to use standard to start with. You can then evaluate

the sort of use you give the detector and decide whether the investment in rechargeables is justified.

Battery

compartment

Battery

compartment

Charger

socket Headphone

socket

CS5MXP VELLEMAN

- 5 -

The batteries should be fitted in the holder which is located in the battery compartment. To fit new batteries first

check the power switch on the unit is switched to OFF. Then loosen the two captive screws located in the battery

cover (do not fully remove these from the cover) and remove the cover. Inside is the battery holder. Lift out the

holder and detach the connector if it is already fitted. Load it with the eight batteries ensuring that each battery is

inserted the correct way round, (direction of batteries alternating). Roll each individual battery to ensure it is located

correctly and making proper contact. Replace the connector making sure that its is firm and well seated, and put

the loaded holder into the housing. Fit the cover and tighten the two captive screws finger tight.

Note : Zinc Carbon batteries should not be left in the detector for long periods where they could leak, so remember

to remove them at the end of a day's searching.

BATTERY CHECK

A battery condition indicator is provided on the detector. To do this for the first time prior to reading the remainder

of the operating instructions proceed as follows : - Turn the SENSITIVITY (POWER) control on. Press the centre

push switch marked BATT CHECK and hold down. The meter will indicate in the green area if the batteries are

good and in the left or central position if the batteries need replacing or recharging. Release the switch and turn the

SENSITIVITY control off. Rechargeable batteries will not read as high into the green as standard batteries even

when fully charged. They also give less indication of discharge on the meter during use.

CONTROLS AND WHAT THEY DO

The CS-5MXP has been designed to offer simplicity of use with high, reliable performance.

The control panel comprises three rotary controls, three push buttons, one toggle switch and a meter.

i. On/Off Sensitivity

Switches detector on by rotating clockwise and adjusts sensitivity to metal.

The CS-5MXP is a silent operating machine and you should rotate the Sensitivity Control clockwise to the

position where the audio threshold tone is comfortable.

Operate the Sensitivity at the highest level possible but, if you experience interference from

external radio transmissions or soil mineralisation, reduce the level to eliminate this.

Checking The Batteries

HOLD

PUSH SWITCH

CS5MXP VELLEMAN

- 6 -

ii. Disc 1

In the clicked off position, the CS-5MXP detects all metal objects.

Turned clockwise it becomes a fully variable discrimination control.

Discrimination is a means of ignoring objects which are generally regarded as junk whilst still detecting the

good objects.

At the lowest setting most iron objects are ignored. Increase the setting and the unit will ignore even larger

pieces of aluminium paper as well as iron.

At higher levels still, ring pulls will be ignored. You must, however, realise that at this higher setting you will

also lose some low denomination and silver hammered coins, so set the control only as high as necessary

to ignore iron and foil contamination (e.g. level 5 is typical).

1. Disc 1 4. Pinpoint push select button

2. Disc 2 5. Disc 2 push select button

3. On/Off - Sensitivity 6. Boost

7. Signal Meter

CS5MXP VELLEMAN

- 7 -

iii. Disc 2

This control is identical to Disc 1 and allows you to further identify the target signal being received.

With Disc 1 set at 5 to reject small iron and silver foil, commence searching. Remember the CS-5MXP is a

motion machine which means that the search head needs to be constantly sweeping, except when in pin

point mode.

You now need to set Disc 2 to ignore ring pulls.

Sweep the head above a ring pull and rotate Disc 2, at the same time depressing the Disc 2 push select

button with the thumb of the hand holding the machine. When the ring pull signal disappears this control is

set. Release the push button.

Your CS-5MXP automatically operates in Disc 1 so commence searching (see "Sweeping Technique".

When you receive a signal, this indicates that the target could be a silver hammered coin, ...

Depress the Disc 2 button and hold it in. Sweep the target object again. If you are still receiving a signal,

then it is likely to be any of the metal found above ring pulls ...

Disc 2 gives you greater analytical skills than a single discrimination machine but, even when Disc 2 does

not give a signal, still dig the target to avoid losing silver hammered etc.

Effect of Discriminate Control Position

CS5MXP VELLEMAN

- 8 -

Three points to remember :

1. Large iron objects, particularly if near the surface, can produce a signal regardless of discrimination settings.

2. Although Disc 1 and 2 are set to ignore metals at the same position there may be slight variations in your

machine and between different machines.

3. Practice, in air, with various metal objects so you understand the detector capabilities and responses.

The more familiar you become with your CS-5MXP Metal detector the more skilful combinations of Disc 1 & 2 you

will use. The following chart gives a few ideas of setting and the conditions under which you would employ them.

DISC SETTING

REF DISC 1 DISC 2 WHEN USED

A 0 0 All metal detecting

B 5 0 Dig all signals

C 5 7 To analyse possible ring pulls etc (see above)

D 5 10 If searching for modern currency (e.g. coins) in a highly screw cap

contaminated site (e.g. picnic area)

E 7 0 Use on beach or picnic site which is highly ring pull contaminated

F 10 0 Use on same sites as above except where highly screw cap

contaminated.

NOTES : i) When using references E & F please be sure that the search site would not yield silver

hammered coins which may be ignored at these high discrimination settings.

ii) In reference A, you way need to reduce sensitivity in highly mineralised or beach sites

iii) These settings are guidelines only and you should practice with various known objects

to ensure that you are familiar with the settings correct for your machine.

iv. Disc 2 Push Select Button

See Disc 2 control above.

v. Pinpoint Push Select Button

At stated earlier the CS-5MXP is a motion machine which requires the head to be constantly moving.

When you have located a target you must pinpoint it carefully to avoid unnecessary digging.

When held down, the pinpoint button enables the detector to give a varying response which peaks directly

above the target.

To pinpoint a target carry out the following procedure :

1. Move the search head to a known clear patch.

2. Hold the pinpoint button down and return the head to the target area ; move it slowly and listen for the

peak response.

The all metal pinpointing mode gives a positive response to all metal irrespective of the Discriminate

setting.

It is not necessary to sweep the target as the pinpoint mode will respond even when held stationary over

the object although the target will fade gradually if the head is held over it for too long.

CS5MXP VELLEMAN

- 9 -

vi. Signal Meter/Battery Check

This is a visual indication of the signal strength giving the experienced user more information about the

target. This is particularly useful for pinpointing. When the BATT CHECK is pressed, the meter will indicate

condition of the batteries. If the meter reading falls below the green band, the batteries should be replaced.

vii. Boost Hi/Normal

For general detecting work, NORMAL mode should be selected.

When increased sensitivity to deep objects is required, then the setting HI should be used. However, if

false signalling occurs due to soil mineralisation, revert to the NORMAL setting.

OPERATING YOUR CS-5MXP

Check the batteries are in good condition prior to searching. Frequently check the battery condition during the

search. Rechargeables give little warning of failure so ensure they are fully charged prior to a long period of

searching or carry a fresh set with you. (See Batteries).

The unit may operate with reduced sensitivity for a period after indicating 'flat' batteries. However the batteries

should be replaced or recharged at the first opportunity.

Use headphones when possible. Not only do they extend the battery life, but they also cut out extraneous noise.

(It is instructive to bury some objects in a clear patch of soil and note the response when swept at different rates

with DISCRIMINATE at various levels). Large pieces of iron are difficult to ignore and may give confusing signals.

An aid to determine whether the target is iron or not is to go into an all metal mode either by turning the

DISCRIMINATE off or simply by pressing the PINPOINT button. Iron objects will generally give a stronger more

positive signal than good objects.

When operating on the beach the all metal mode may give a response to the beach itself. If this is the case operate

the unit with the DISCRIMINATE level set to the point at which it is ignored.

If in doubt as to whether a target is good or not - dig it. Your knowledge of how the detector responds will increase

each time and soon make your more sure.

Normal and Pinpoint Response

SOUNDLEVEL

NORMAL RESPONSE PINPOINT RESPONSE

CS5MXP VELLEMAN

- 10 -

DETECTION RANGE

Detection ranges will vary depending on the size of the object, the length of time an object has been buried, and

the type of ground the object is buried in.

The best ground conditions are well compacted soils and coins can be found at the greatest depths if the object

has been buried for some time and the coin has interacted with the salts in the ground, thereby appearing larger to

the detector. The worst conditions for detecting are on loosely compacted or freshly dug ground or when the object

has only recently been buried. In these conditions detection range will be reduced. 90% of all artefacts are found

within 6" (20 cm) of the surface.

N.B. Your CS-5MXP is a top performance deep seeker but adverse soil conditions can significantly reduce the

depth of detection.

DETERMINING THE TARGET SIZE AND DEPTH

An operator who is familiar with his instrument will be able to do an excellent job of determining object size, shape,

and depth before he digs. This technique is learned from careful analysis of the audio signals coming from the

detector. Each time a signal is heard, listen for any peculiar characteristics it may have, determine over how large

an area you get a detector signal, and try to "outline" the object before you dig.

After digging up the object, compare the object size, shape, depth and position in the ground with signal

information you received before digging. After careful analysis of many digs, you will learn to "read" the hidden

target before digging.

ACCESSORIES (OPTIONAL)

Headphones

Headphones not only extend battery life but improve sensitivity by cutting extraneous noise. The headphones

should be fitted with a standard ¼ inch (6.3 mm) jack plug. The headphone socket is located under the protective

cap in the battery housing.

Rechargeable battery pack

A shrink wrapped pack of 8 rechargeable NiCd batteries to replace the standard batteries and holder.

Battery charger

The C-SCOPE battery charger is designed to charge the rechargeable pack quickly and safely.

CHARGING BATTERIES

A battery charge socket is provided for use with the C-SCOPE battery charger (See Accessories) and is located

under the protective cap in the battery housing. (The smaller of the two sockets.) Inserting the charger will

automatically remove the power from the detector so the charger must be removed to do a battery check. Do not

attempt to recharge standard batteries. It will take between eight and fifteen hours to fully recharge flat batteries

with the C-SCOPE charging unit.

Inhaltsverzeichnis

Sprachen:

Andere Velleman Metalldetektor Handbücher

Velleman

Velleman CS120 Bedienungsanleitung

Velleman

Velleman CS400 Bedienungsanleitung

Velleman

Velleman CS1M Bedienungsanleitung

Velleman

Velleman C.Scope CS990 Bedienungsanleitung

Velleman

Velleman PEREL CMD02 Bedienungsanleitung

Velleman

Velleman CS100 Bedienungsanleitung

Velleman

Velleman C.Scope CS660 Bedienungsanleitung

Velleman

Velleman CS130 Bedienungsanleitung

Velleman

Velleman CS100N Bedienungsanleitung

Velleman

Velleman C.SCOPE CS-5MXP Bedienungsanleitung

Velleman

Velleman CS220 Bedienungsanleitung

Velleman

Velleman TREASURE HUNTER CS50 Bedienungsanleitung

Velleman

Velleman CS102 Bedienungsanleitung

Velleman

Velleman CS130 Bedienungsanleitung

Velleman

Velleman C.Scope CS770 Bedienungsanleitung

Velleman

Velleman CS300 Bedienungsanleitung

Velleman

Velleman ED21120 Bedienungsanleitung

Velleman

Velleman CS150N Bedienungsanleitung

Velleman

Velleman CS100 Bedienungsanleitung

Velleman

Velleman TREASURE HUNTER CS50 Bedienungsanleitung

Velleman

Velleman ED21300 Bedienungsanleitung

Velleman

Velleman CS300 Bedienungsanleitung

Velleman

Velleman CS200 Bedienungsanleitung

Velleman

Velleman CS150 Bedienungsanleitung

Beliebte Metalldetektor Handbücher anderer Marken

Garrett

Garrett MAGNASCANNER CS 5000 Bedienungsanleitung

Valex

Valex 1800200 Bedienungsanleitung

Gauss

Gauss MIL MD Bedienungsanleitung

Sears

Sears 321.596370 Bedienungsanleitung

Eriez

Eriez X8 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-22 Bedienungsanleitung

Zircon

Zircon MetalliScanner m60c Bedienungsanleitung

nalanda

nalanda MD027 Bedienungsanleitung

REV Ritter

REV Ritter CB-7005 Bedienungsanleitung

Minelab

Minelab F1A4 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs F70 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-12 Bedienungsanleitung

GOLDEN MASK

GOLDEN MASK 5 Bedienungsanleitung

Grizzly

Grizzly YM 203 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Probe 560 Bedienungsanleitung

Accurate Locators

Accurate Locators XL16 IMAGER Bedienungsanleitung

Teknetics

Teknetics G2 Bedienungsanleitung