Velleman DVM66 Bedienungsanleitung

DVM66

Dual Display

Digital Multimeter

OPERATION MANUAL

GEBRUIKERSHANDLEIDING

MANUEL D’UTILISATEUR

IEC-1010

VELLEMAN GB1

DVM66

Dual Display Digital Multimeter

1 Safety information

This multimeter has been designed according to IEC-1010 concerning electronic

measuring instruments with an over voltage category (CAT II) and pollution 2.

Follow all safety and operating instructions to ensure that the meter is used safely

and is kept in good operating condition.

1.1 Preliminary

•When using the meter, the user must observe all normal safety rules

concerning :

- Protection against the dangers of electrical current.

- Protection of the meter against misuse.

•Full compliance with safety standards can be guaranteed only if used with test

leads supplied. If necessary, they must be replaced with the same model or

same electric ratings. Measuring leads must be in good condition.

1.2 During use

•Never exceed the protection limit values indicated in specifications for each

range of measurement.

•When the meter is linked to a measurement circuit, do not touch unused

terminals.

•Components should not be connected to the hFE socket when measuring

voltages with test leads.

•Before rotating the range selector to change functions, disconnect test leads

from the circuit under test.

•When carrying out measurements on TV or switching power circuits, always

remember that there may be high amplitude voltage pulses at test points

which can damage the meter.

VELLEMAN GB2

•Never perform resistance measurements on live circuits.

•Never perform capacitance measurements unless the capacitor to be measured

has been discharged fully.

•Always be careful when working with voltages above 60V DC or 30 V AC

rms. Keep fingers behind the probe barriers while measuring.

1.3 Symbols

Important safety information, refer to the operating manual.

Dangerous voltage may be present.

Earth ground

Double insulation (Protection class II).

Indicates that the fuse must be replaced with one having the ratings indicated.

1.4 Maintenance

•Before opening the meter, always disconnect test leads from all sources of

electric current.

•For continue protection against fire, replace fuse only with the specified

voltage and current ratings :

F1 : F 500mA/250V F2 : F 10A/250V

•If any faults or abnormalities are observed, the meter can not be used any

more and it has to be checked out.

•Never use the meter unless the back cover is in place and fastened fully.

•To clean the meter, use a damp cloth and mild detergent only, do not use

abrasives or solvents on it.

VELLEMAN GB3

2. Description

This meter is an auto ranging professional measuring instrument with 3 ¾ digit

LCD, capable of performing functions :

- DC and AC voltage measurement - DC and AC current measurement

- Resistance measurement - Capacitance measurement

- Frequency measurement - Transistor and Diode test

- Audible continuity test

Some special functions and features are provided. They are very useful for

electrical and electronic measurement.

All the functions are designed to be very convenient to use. You can get used to

working with this meter quickly.

2.1 Panel configuration

LCD Display

ôFunction buttons

o Record o Rel o Range

o A-H o AC-DC/

o Hz/∆%

íRotary Switch

÷V/Ω/F Input Jack

ûCOM Input Jack

ømA input Jack

ù10A Input Jack

VELLEMAN GB4

Following table shows the button configuration for all function positions.

Function ACV DCV ΩhFE CAP FREQ mA A

Range A/M A/M A/M M F F A/M A F F

Record o o o o o o o

Rel ooo ooo oo

A-H ##oooo

##oo

AC-DC o o

Hz o

∆% ooo ooo oo

A/M: Auto and manual ranging provided. M: Manual ranging only F: Range fixed.

#: A-H function is not valid for 200mV range.

##: A-H function in Freq. Measuring is different from normal. See paragraph 2.5.

2.2 Record button

•Push this button to enter into

Record mode.

-MIN MAX AVG signs light

- Main display shows the real

time measuring value.

- Secondary display shows the

recording time. At the first

minute display shows seconds

and then only minutes and

hours.

- This meter starts to record the

max. and min. value measured

and calculate the average

automatically.

VELLEMAN GB5

•To read out recorded value, push this button more.

-MAX MIN AVG lights in sequence

- Main display shows the recorded value or the average.

- Secondary display shows the time when the max. value or the min. value was

recorded.

•Hold this button for more than 3 seconds to return to the normal operating

mode.

2.3 Rel button

•Push this button to enter into

Rel measuring mode.

-REL sign lights.

- Main display shows the relative

value.

Relative value = Real time value

- Reference value.

- Secondary display shows the

reference value.

•Push this button again to get Rel

% measurement.

-REL % signs light.

- Main display shows the relative

percent value.

Relative percent value = Rel.

Value/reference x 100 %

- Secondary display remains the

reference value.

- Bargraph shows the percentage

tolerance specified.

•If measurement result is within

the tolerance range, built-in

buzzer will sound.

VELLEMAN GB6

•To change the percentage

tolerance, use ∆% button. Per

pushing increases 0.5% until

10%. The bar graph consists of

12 bars in this case. One bar of

the 2nd to 11th indicates 1% and

the 13th indicates 0.5%. For

example, right figure indicates

5.5% tolerance.

•Hold this button for more than 3

seconds to exit.

2.4 Range Button

•Range button is used to change ranging mode between Auto and Manual.

When a function with A/M ranging mode is selected, the meter enters auto

ranging at first. To change to manual ranging, push this button once.

•When the meter operates in manual ranging mode, push this button to change

range to the higher one and hold this button for more than 3 seconds to return

to auto ranging mode.

2.5 A-H Button

•Auto data hold is a very useful function for real time measurement. Just push

A-H button to hold the last measuring result. When a new measurement is

made, the meter will hold the new value automatically. This function remains

valid until pushing the A-H button to release the meter.

•New value mentioned above means a value much different from the old. In

most of measurements with this meter, 10 digit difference is enough. But in

resistance measuring, maybe less than 20 digits will not result in a new

holding.

VELLEMAN GB7

•In frequency measurement, the A-H feature is somehow different. Pushing

this button only freezes the operation of meter, but does not auto-hold

reading. It means that LCD display will keep the value not variant, even

though the frequency of input changes greatly. In this case, the sign A-H is

flashing to show the functional difference.

•In high resistance and large capacitance measuring, as the meter has to take

time to get stable reading, so some transient changes of inputs do not affect

the held value.

2.6 AC-DC/ Button

•This button is used to change current measurement between AC and DC

mode.

•The second function of this button is to set up a continuity testing mode in

resistance measurement position. A special feature provided by this meter is

that the continuity testing can be executed at any resistance ranges. To make

continuity testing at the desired range, just use the range button after pushing

button.

2.7 Hz/ ∆% BUTTON

•When measuring frequency, push this button will change the contents of LCD

display. The main display will show the AC voltage value of input signals.

At the same time, the frequency of inputs will appear on the secondary

display.

•In relative value measurement mode, this button is used to specify the

percentage tolerance as described in paragraph 2.3.

VELLEMAN GB8

2.8 Input Jacks

This meter has four input jacks that are protected against overload to the limits

shown in the table. During use, connect the black test lead to the COM jack and

the red test lead as below :

Function Red Lead Connection Input Limits

DCV/ACV V/Ω/F 1000V DC or 750V rms AC

Ω/ / V/Ω/F 250V DC or rms AC

CAP. V/Ω/F 250V DC or rms AC

FREQ. V/Ω/F 250V DC or rms AC

mA mA 400mA DC or rms AC

A A 10A DC or rms AC

mA and A ranges are protected by fuses

3. Operating Instruction

3.1 Measuring voltage

1. Connect the black test lead to the COM jack and the red test lead to the V/Ω/F

jack.

2. Set the function switch at V or V range to be used and connect test leads

across the source or load under measurement.

3. Read LCD display. The polarity of red connection will be indicated when

making a DC measurement.

3.2 Measuring current

1. Connect the black test lead to the COM jack and the red test lead to the mA jack for

a maximum of 400mA. For a maximum of 10A, move the red lead to the A jack.

2. Set the function switch at mA or A range to be used and push AC-DC button

to select DCA or ACA measuring mode.

3. Connect test leads in series with the load in which the current is to be

measured.

4. Read LCD display. The polarity of red lead connection will be indicated

when making a DC measurement.

VELLEMAN GB9

3.3 Measuring Resistance

1. Connect the black test lead to the COM jack and the red teas lead to the

V/Ω/F jack. (NOTE : The polarity of the red lead connection is positive “+”)

2. Set the function switch at Ωrange to be used and connect test leads across the

resistance under measurement.

NOTE :

1. For resistance above 4MΩ, the meter may take a few seconds to stabilize

reading. This is normal for high resistance measuring.

2. When the input is not connected, i.e. at open circuit, the figure “OL” will be

displayed for the over range condition.

3. When checking in-circuit resistance, be sure the circuit under test has all

power removed and all capacitors are fully discharged.

3.4 Measuring Capacitance

1. Connect the black test lead to the COM jack and the red test lead to the V/Ω/F

jack. (NOTE: The polarity of the red lead connection is positive "+").

2. Set the function switch at position.

3. Connect test leads across the capacitor under measurement and be sure that

the polarity of connection is observed.

4. When rest leads are not connected to a capacitor, the LCD may not show zero

but a few digits, this is normal for the stray capacitance of test leads and input

circuit of the meter always exists. These digits can be deleted by using Rel.

Operating mode before applying test leads.

3.5 Measuring Frequency

1. Connect the black test lead to the COM jack and the red test lead to the V/Ω/F

jack.

2. Set the function switch at the FREQ. Position and connect test leads across

the source or load under measurement.

NOTE :

The input voltage should be between 1V and 10V rms ac. If the voltage is

more than 10V rms, reading may be out of the accuracy range.

Inhaltsverzeichnis

Andere Velleman Multimeter Handbücher

Velleman

Velleman DVM830 Bedienungsanleitung

Velleman

Velleman DVM852 Bedienungsanleitung

Velleman

Velleman DVM101 Bedienungsanleitung

Velleman

Velleman DVM850BL Bedienungsanleitung

Velleman

Velleman DVM898 Bedienungsanleitung

Velleman

Velleman EVM892 Bedienungsanleitung

Velleman

Velleman DVM835 Bedienungsanleitung

Velleman

Velleman DVM1100 Bedienungsanleitung

Velleman

Velleman DVM630 Bedienungsanleitung

Velleman

Velleman DVM3218 Bedienungsanleitung

Velleman

Velleman AVM360 Bedienungsanleitung

Velleman

Velleman DVM990BL Bedienungsanleitung

Velleman

Velleman DVM855 Bedienungsanleitung

Velleman

Velleman DVM900 Bedienungsanleitung

Velleman

Velleman DVM893 Bedienungsanleitung

Velleman

Velleman DVM92 Bedienungsanleitung

Velleman

Velleman DVM1190 Bedienungsanleitung

Velleman

Velleman DVM894 Bedienungsanleitung

Velleman

Velleman DVM1400 Bedienungsanleitung

Velleman

Velleman DVM6243 Bedienungsanleitung

Velleman

Velleman DVM831 Bedienungsanleitung

Velleman

Velleman DVM2000 Bedienungsanleitung

Velleman

Velleman DVM4200 Bedienungsanleitung

Velleman

Velleman DVM1100 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung