Velleman VELBUS VMB1TSW Bedienungsanleitung

MULTIROOM TEMPERATURE CONTROLLER SYSTEMMULTIROOM TEMPERATURE CONTROLLER SYSTEMMULTIROOM TEMPERATURE CONTROLLER SYSTEM

Up to 32 sensors per controller

Up to 7 zones

Up to 31 program instructions can be saved per sensor or zone

Program types :

day programs

working day programs

weekend programs

week programs

Power supply: 12VDC ... 18VDC/50mA

VMB1TC

VMB1TSVMB1TSVMB1TS

VMB1TCW

VMB1TSWVMB1TSWVMB1TSW

There are several manuals available for

this temperature control system:

1. Getting started manual, This guide can be

found in the sensor package, and provides

an overview of the system. Read this first!

2. This manual, use it together with the getting

started manual for standard system set-up.

3. An extended manual is available for down-

load. Use this manual for special features

and to study examples.

4. A controller menu overview sheet is also

available for download, used as reference.

IMPORTANT: VMB1TS(W) and VMB1TC(W) modules

have the unique feature of user firmware update!

Due to the large amount of applications, check our

web site for manual updates and firmware updates.

Updates can add or improve functionality, not de-

scribed in these manuals.

Your current firmware version can be checked using

the Velbuslink PC software.

In this manual:

1. How to connect the temperature controller p.4

2. How to connect the temperature sensor p.5

3. Setting the address for sensor and controller p.6

4. Assign a relay channel to a temperature sensor function p.7

5. Set the menu language on the controller p.8

6. Setting the clock for the controller p.9

7. How to set up the sensor with the controller p.10

8. Operating the temperature controller p.12

9. Programming the temperature controller p.16

10. Screen & LED indicators p.21

11. Controller menu overview p.22

1. Temperature controller 'VMB1TC' connection

Connection Battery backup

To avoid losing the clock when a power failure occurs, a

backup battery (3V Lithium CR2032) can be installed in the

battery holder at the back of the module.

To avoid premature depletion of the battery, only install it

when permanent power is supplied to the Velbus system.

ENGLISH

Place the TERM jumper if the module is

connected at the start or end of a cable on the

Velbus.

Remove the jumper in all other cases. Place a jumper on the

end module of the longest cable only, NOT on each end point.

E.g. a normal two-story house will have 3 terminators: 1 up-

stairs end point, 1 downstairs end point and 1 in the fuse box.

2. Temperature sensor 'VMB1TS' connection and button+indicators overview

ENGLISH

BUS TWISTED PAIR (0.5mm²)

6 7

10 11 12 13

LED indication Settings

1Cooling mode 8Address setting*

2Comfort mode 9Terminator

3Day mode

4Night mode Wiring

5Heating or air-conditioning on 14 power supply 12 to 18Vdc

15 Velbus

Sensor

6Temperature sensor

Controls

7Mode pushbutton

7+11 Assign high temperature alarm*

7+12 Assign low temperature alarm*

7+13 Assign circulation pump*

10 Assign airco (COOL)*

11 Assign day setup for Central heating (DAY)*

12 Assign extra fan for boost heat (BOOST)*

13 Assign heater (HEAT)*

* only available for the VMB1TS module

ENGLISH

3. Address selection

In order to identify each module in your system it is necessary to set an unique address for each module.

This address will also be used by the PC software to scan all the addresses and to identify the modules.

Example of a valid address: “0 1”

1. Press and HOLD the ‘Menu’ button to open the extended menu.

2. Scroll through the extended menu using

↑

↓

buttons until the ‘’Configuration”

menu appears, select using the

→

button.

3. Scroll through the Configuration menu using

↑

↓

buttons until the ‘’Address”

menu appears

4. Select the Address menu using the

→

button.

5. Enter a unique address (‘01’...‘FE’) using the

↑

↓

button.

6. Confirm the address using the

→

button.

7. Exit the menu using the



button.

VMB1TC : ADDRESS SETTING USING THE MENU

↑

3 421

6 7

Each module on the Velbus system must have its own unique

address, write down the address for later use!

VMB1TSW / VMB1TCW

VMB1TS : ADDRESS SETTING USING THE 2 ADDR ROTARY SWITCHES.

CAUTION: Addresses 81,91,A1, B1, C1, D1, E1, F1 & FF can NOT be used. Examples of valid

addresses: 01, 02, 03…. 0A, 0B…, 1A, 1B…

A total of 248 valid addresses can be selected for this module.

Adress setting trough Velbuslink©

ENGLISH

4. Assign a relay channel to a temperature sensor function (can also be performed using PC, advised)

On the sensor module:

Set the sensor module in anti-freeze mode by pressing the push button on the front panel repeatedly until all LED’s are off.

On the relay module:

ModeTime1

ADDR

First remember the address of the

module to reinstate it later on. Set the

Address rotary switches to 'C1', 'C2',

'C3, or 'C4', depending on the chosen

channel. The 'MODE' LED of that

channel will flash to indicate learning

mode.

Set the MODE and TIME1 rotary switches of the

chosen channel to

'0' (instant control)

Only available for VMB1TS

Select one of the below functions: (ask someone to help if needed)

To assign a room heater or room water valve to a relay contact (>> this will mostly be used)

Press button 13 on the sensor until relay engages

To assign the air-conditioning system (fan or compressor control) to a relay contact:

Press button 10 on the sensor until relay engages.

To assign the central heating system day/night setting to a relay contact:

Press button 11on the sensor until relay engages.

To assign an extra fan for quick heating or cooling (boost) to a relay contact:

Press button 12 on the sensor until relay engages

To assign the central heating system main pump to a relay contact

Press button 7+ button 13 on the sensor until relay engages

To assign a low temperature alarm to a relay contact

Press button 7+ button 12 on the sensor until relay engages

To assign a high temperature alarm to a relay contact

Press button 7+ button 11 on the sensor until relay engages

10 11 12 13

Do not forget to set the address of the

relay module back to its original value.

Repeat the procedure for other sen-

sors or other functions.

ENGLISH

5. Set the menu language on the controller

1. When applying power to the controller for the

first time, only the time is shown on the display.

2. Press and HOLD the ‘Menu’ button to open the

extended menu. Scroll to “Configuration” menu

using the ↑or ↓buttons. Confirm using the →

button.

3. Enter the language menu using the →button.

4. Choose the desired language using the ↑or ↓

buttons.

5. Confirm the language selection using the →button.

6. Exit the menu using the button.

↑

See display & menu overview on page 21 & 22

6. Setting the clock

ENGLISH

It is important to set the correct time for the internal clock.

Setting the time on this module will synchronise all clocks in your Velbus system.

2 5

When applying power to the controller for the first time,

only the time is shown on the display.

1. Open the “short” menu by pressing the ‘Menu’ button.

2. Scroll to "clock set" menu using ↑or ↓buttons.

3. Select the set clock menu using the →button. The day-

indication flashes.

Set the day using ↑or ↓buttons.

Confirm using the →button. The hour-indication flashes.

Set the hour using ↑or ↓buttons.

Confirm using the →button. The minutes-indication flashes

Set the minutes using ↑or ↓buttons.

4. Confirm using the →button to start the clock from the set

time.

5. Exit the menu using the button.

See display & menu overview on page 21 & 22

↑

7. Sensors setup

ENGLISH

Before the controller can work with the temperature sensors it must first scan the network for all connected sensors.

If temperature sensors are installed or removed afterwards, the search process must be repeated to update the list of

sensors to the new situation. NOTE: Make sure "all rooms" or "zone" is not selected.

1. Press and HOLD the ‘Menu’ button to open the extended menu.

Scroll through the extended menu using ↑or ↓buttons until the

‘Configuration’ menu appears. Select the configuration menu

using the →button.

2. Scroll through the Configuration menu using ↑or ↓buttons until

the ‘Scan sensors’ item appears.

3. Confirm the scan sensors menu using the →button.

The search for sensors on the network is now in progress.

4. Once the search process is completed, the first of the connected

temperature sensors is shown on the display.

Searching for temperature sensors

↑

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Velleman Temperaturregler Handbücher

Velleman

Velleman K641LX Bedienungsanleitung

Velleman

Velleman WS8426 Bedienungsanleitung

Velleman

Velleman VMB1TC Bedienungsanleitung

Velleman

Velleman VMA335 Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema