Velleman K2579 Bedienungsanleitung

K2579

ILLUSTRATED ASSEMBLY MANUAL H2579IP-1

Total solder points: 49

Difficulty level: beginner 1 2 3 4 5 advanced

Smallsizetimer providesup to

60 minutesdelay.

UNIVERSAL START/STOP TIMER

Specifications

Relay output with switchover contact.

Power supply : 12VDC regulated.

Typical active current : 55mA.

Relay output : 2A/240V max.

 Dimensions : 38x69mm / 1.5”x2.7”.

VELLEMAN NV

Legen Heirweg 33

9890 Gavere

Belgium Europe

www.velleman.be

www.velleman-kit.com

The K2579 is a basic timer with relay output for time intervals of up to 15 minutes.

Set the desired delay with the trimmer.

The maximum delay can easily be lengthened and the timer can be stopped and restarted at any time.

Features

Start / stop push buttons included.

LED status indicator.

Timing adjustable from a few seconds to 15 minutes, extendable to 60 minutes.

Relay output with switchover contact.

Specifications :

 Power supply : 12VDC regulated.

 Typical idle current : 20mA.

 Typical active current : 55mA.

 Relay output : 2A/240V max.

 Dimensions : 38x69mm / 1.5”x2.7”.

Features & Specifications

Assembly hints

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will protect the tip,

and enables you to make good connections. When solder rolls off the tip, it needs cleaning.

• Thin raisin-core solder. Do not use any flux or grease.

• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot fly towards the eyes.

• Needle nose pliers, for bending leads, or to hold components in place.

• Small blade and Phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

Make sure the skill level matches your experience, to avoid disappointments.

Follow the instructions carefully. Read and understand the entire step before you perform each operation.

Perform the assembly in the correct order as stated in this manual

Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.

Values on the circuit diagram are subject to changes, the values in this assembly guide are correct*

Use the check-boxes to mark your progress.

Please read the included information on safety and customer service

* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.

0.00

1.3 Soldering Hints :

1- Mount the component against the PCB surface and carefully solder the leads

2- Make sure the solder joints are cone-shaped and shiny

3- Trim excess leads as close as possible to the solder joint

DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE.

ALWAYS CHECK THEIR VALUE ON THE PARTS LIST!

REMOVE THEM FROM THE TAPE ONE AT A TIME !

R1 : 1K (1 - 0 - 2 - B)

R2 : 10K (1 - 0 - 3 - B)

R3 : 4K7 (4 - 7 - 2 - B)

R4 : 1K (1 - 0 - 2 - B)

R5 : 10K (1 - 0 - 3 - B)

R6 : 4K7 (4 - 7 - 2 - B)

R7 : 1K (1 - 0 - 2 - B)

2. Resistor

R...

Construction

D1 : 1N4148

1. Diode. Watch the polarity !

D...

CATHODE

RV1 : 2M2

5. Trim potentiometer

IC : 8p.

3. IC socket. Check the

position of the notch!

C1 : 100nF

4. Capacitor

C...

T1 : BC547B

6. Transistor

C2 : 100µF

7. Electrolytic Capacitor.

Watch the polarity !

LD1 :5mm RED

8. LED. Check the polarity!

LD...

COLOR = 2...5

CATHODE

C...

Construction

SW1: START

SW2: STOP

9. Push buttons

RY : VR15M121C

10. Relay

RY...

IC : NE555

11. IC. Check the position of

the notch!

12. Connection example

SW1

SW2

START

STOPD1

LD1

AB C

RV1

220nF/400V

100E/1W

ABorC

Snubber network*

*see hook-up and use

12V DC

300 mA

COM

Connection example

Hook-up and use

Connect the unit with a 12VDC regulated power supply as shown in the example.

Turn the trimmer all the way counterclockwise.

Push the START button. The relay will be activated momentarily.

The position of the trimmer determines the ON-time. Turn it clockwise to increase the ON-time.

Increase the value of C2 for an even longer activation duration.

The unit can be stopped at any time by pressing the STOP button.

The START and STOP buttons can be mounted in a remote location. Make sure to use screened cable,

avoid outside interference and keep the distance between the switches and the PCB as short as possible.

The timer is equipped with a relay output that is galvanically separated from the rest of the circuit for extra

safety. The connection example lists the function of the pins of the relay contacts.

If the relay is used to switch important inductive loads, such as electric motors or transformers, it may be

necessary to install a snubber network across the relay contacts to avoid excessive contact wear.

Ensure that the power supply of the circuit is sufficiently HF decoupled. Noise impulses entring

trough the power supply may start and stop the circuit unnecessarily.

13. Hook-up and use

10. PCB layout.

PCB

14. PCB layout.

Inhaltsverzeichnis

Andere Velleman Timer Handbücher

Velleman

Velleman TIMER12 Bedienungsanleitung

Velleman

Velleman Timer10 Bedienungsanleitung

Velleman

Velleman MK188 Bedienungsanleitung

Velleman

Velleman Perel E305W2 Bedienungsanleitung

Velleman

Velleman ED8A000 Bedienungsanleitung

Velleman

Velleman TIMER6 Bedienungsanleitung

Velleman

Velleman TIMER11 Bedienungsanleitung

Velleman

Velleman TIMER8 Bedienungsanleitung

Velleman

Velleman EDIN305N Bedienungsanleitung

Velleman

Velleman TIMER5 Bedienungsanleitung

Velleman

Velleman PEREL E305DD Bedienungsanleitung

Velleman

Velleman TIMER8S Bedienungsanleitung

Velleman

Velleman WT3116 Bedienungsanleitung

Velleman

Velleman TIMER10N Bedienungsanleitung

Velleman

Velleman K8041 Bedienungsanleitung

Velleman

Velleman Timer10 Bedienungsanleitung

Velleman

Velleman TIMER2 Bedienungsanleitung

Velleman

Velleman TIMER7 Bedienungsanleitung

Velleman

Velleman TIMER9 Bedienungsanleitung

Velleman

Velleman VM102 Bedienungsanleitung

Velleman

Velleman PEREL E305WON Bedienungsanleitung

Velleman

Velleman TIMER9 Bedienungsanleitung

Beliebte Timer Handbücher anderer Marken

Intermatic

Intermatic P1131 Bedienungsanleitung

Learning Resources

Learning Resources Time Tracker mini Bedienungsanleitung

CEBEK

CEBEK I-215 Bedienungsanleitung

Somogyi

Somogyi home TS MD 5 Bedienungsanleitung

Profile

Profile 010200280 Bedienungsanleitung

Gizmo

Gizmo T4 Bedienungsanleitung

Tekmar

Tekmar Timer 031 Bedienungsanleitung

Daikin

Daikin DST301B61 Bedienungsanleitung

sisel

sisel ENDA ETM2432 Bedienungsanleitung

B&Q

B&Q TE103 Bedienungs- und Wartungshandbuch

Hozelock

Hozelock AC Plus 2700 Bedienungsanleitung

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Bedienungsanleitung

Tork

Tork TU40 Bedienungsanleitung

Emos

Emos EMT400F Bedienungsanleitung

FarmTek

FarmTek Polaris Bedienungsanleitung

Maximum

Maximum CRONUS Bedienungsanleitung

Uberhaus

Uberhaus TD133B Bedienungsanleitung

Clas Ohlson

Clas Ohlson 31-3766 Bedienungsanleitung