Venmar Connaisseure C700 SERIES Bedienungsanleitung

GLASS PANELS

INSTALLATION INSTRUCTIONS

APPLIES TO THE FOLLOWING RANGE HOOD SERIES

C700, CC700, CIC700, CIS700,

IU600ES, IB700, IC700, IC700ES,

IK700 AND IS700

Venmar Ventilation Inc., 550 Lemire Blvd.

Drummondville QC J2C 7W9

1-800-567-3855

www.venmar.ca

09530 Rev. 02

WARNING

• ITIS RECOMMENDED TO WEAR SAFETY GLASSES AND GLOVES WHILE PREFORMING THESE INSTRUCTIONS.

• HANDLE GLASS PANEL WITH CARE.

• ALL TEMPERED GLASS CAN EXPERIENCE SPONTANEOUS BREAKAGE. IFBROKEN, TEMPERED GLASS FALLS

OUT OF IT’SOPENING IN INTERLOCKING CLUMPS. TEMPERED GLASS CAN, ON OCCASION, BREAK INTO

LARGE SHARDS RATHER THAN THE CLASSIC TINY PIECE PATTERN.

• RISK OF ELECTRICAL SHOCK. BEFORE INSTALLING OR REPLACING THE GLASS PANEL, SWITCH POWER OFF

AT SERVICE PANEL AND LOCK SERVICE DISCONNECTING MEANS TO PREVENT POWER FROM BEING SWITCHED

ON ACCIDENTALLY.

CAUTION

AFTER APOWER FAILURE OR DURING THE RANGE HOOD POWER UP, A5-SECOND BOOTING SEQUENCE

IS EXECUTED. WAIT FOR THE CONTROL BACKLIGHTING TO TURN OFF BEFORE USE.

IFTHE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 4 OF THE HOOD INSTALLATION GUIDE.

IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:

HO0181

Remove filters by pushing them

towards the back of the hood and

tilting them down. Set the filters

aside.

Remove the bottom panel 10 retaining

screws and set aside.

NOTE: Both light assemblies will

have to be disconnected in

order to remove the bottom

panel (see step ).

HO0174

SCREW

LOCATIONS

Slightly pull the bottom panel out.

Press on tabs and pull to disconnect

both light assemblies electrical

harnesses from light connectors.

Slide bottom panel out and set aside.

HO0176

- 2 -

C700 SERIES

Carefully remove the new glass panel from its packaging. Remove new glass panel nuts (factory

installed) from both studs and set aside.

- 3 -

If need be, remove current glass panel

retaining nuts from both studs. Discard

glass panel and nuts.

Insert new glass panel studs in hood

front holes.

While holding glass panel, pre-tighten

previously removed nuts by hand.

Ensure glass panel is flush with top of

hood and centered from side-to-side.

Then, using a 3/8" socket, tighten nuts

completely.

HD0440

GLASS PANEL STUD

NUT

Insert bottom panel in the back of the hood and reconnect each light assembly electrical

harness to its light connector.

Secure bottom panel to the hood, using the 10 previously removed screws.

Reinstall baffle filters.

IFTHE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 4 OF THE HOOD INSTALLATION GUIDE.

IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:

HO0247

Remove filters by pushing them

towards the back of the hood and tilting

them down. Set the filters aside.

FOR 30” WIDE HOODS:

Remove the 7 screws (A only)

retaining the bottom panel, and set

aside.

FOR 36” WIDE HOODS:

Remove the 8 screws (A and B)

retaining the bottom panel and set

aside.

HO0246

Carefully remove the glass panel from its packaging. Remove new glass panel nuts (factory

installed) from both studs and set aside.

C700 SERIES (CONT’D)

IU600ES SERIES

- 4 -

If need be, remove current glass panel retaining nuts from both studs. Discard glass panel and

nuts.

Insert new glass panel studs in hood front holes.

While holding glass panel, pre-tighten previously removed nuts by hand. Ensure glass panel is

flush with top of hood and centered from side-to-side.

Then, using a 3/8" socket, tighten nuts completely.

HD0556

STUD

Reinstall the bottom panel to the hood, using 7 or 8 screws previously removed in step .

Reinstall filters.

FOR EACH GLASS PANEL, IF THE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 6 (CIC700 SERIES)

OR STEP 8 (IK700 SERIES) OF THE HOOD INSTALLATION GUIDE.

IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:

HO0195

Remove filters by pushing them towards the back (opposite control side) of the hood and tilting

them down. Set the filters aside.

Carefully remove the glass panel from its packaging. Remove new glass panel nuts (factory

installed) from both studs and set aside.

HO0253

CIC700 SERIES IK700 SERIES

NUT

IU600ES SERIES (CONT’D)

CIC700 AND IK700 SERIES

If need be, remove current glass panel

retaining nuts from both studs. Discard

glass panel and nuts.

Insert new glass panel studs in

appropriate hood holes (some parts not

illustrated to ease understanding).

NOTE: Install the glass panel with the

control pictogram on the front of

the hood.

While holding glass panel, pre-tighten

previouslyremovednutsbyhand.Ensure

glass panel is centered.

Then, using a 3/8" socket, tighten nuts

completely. HD0438

GLASS

PANEL STUD

NUT

Reinstall filters.

- 5 -

IFTHE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 4 (CC700 SERIES) OR

STEP 6 (CIS700 SERIES) OF THE HOOD INSTALLATION GUIDE.

IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:

Remove filters by pushing them

towards the back (opposite control

side) of the hood and tilting them

down. Set the filters aside.

NOTE: CIS700 Series illustrated at

right and below; some details

of your hood may be slightly

different from the ones shown.

Using a Robertson or a Phillips no. 2

screwdriver, remove the 4 electrical

compartment cover retaining screws.

Set cover and screws aside.

HO0190

HD0437

SCREW

LOCATIONS

CIC700 AND IK700 SERIES (CONT’D)

CC700 AND CIS700 SERIES

Carefully remove the glass panel from its packaging. Remove new glass panel nuts (factory

installed) from both studs and set aside.

If need be, remove current glass panel

retaining nuts from both studs. Discard

glass panel and nuts.

Insert new glass panel studs in

appropriate hood holes.

NOTE: For CIS700 Series, install

the glass panel with the control

pictogram on the front of the

hood.

While holding glass panel, pre-tighten

previouslyremovednutsbyhand.Ensure

glass panel is centered.

Then, using a 3/8" socket, tighten nuts

completely.

Repeat steps and for the second

glass panel installation. HD0439

GLASS

PANEL STUD

NUT

Reinstall electrical compartment cover and baffle filters.

IFTHE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 4 OF THE HOOD INSTALLATION GUIDE.

IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:

Remove filters by pushing them

towards the back (opposite control

side) of the hood and tilting them down.

Set the filters aside.

HO0251

Using a Robertson or a Phillips no. 2

screwdriver, remove the 5 electrical

compartment cover retaining screws.

Set cover and screws aside.

HD0560

SCREW LOCATIONS

- 6 -

CC700 AND CIS700 SERIES (CONT’D)

IB700, IC700 AND IC700ES SERIES

Carefully remove the glass panel from its packaging. Remove new glass panel nuts (factory

installed) from both studs and set aside.

If need be, remove current

glass panel retaining nuts from

both studs. Discard glass panel

and nuts.

Insert new glass panel studs in

appropriate hood holes.

While holding glass panel,

pre-tighten previously removed

nuts by hand. Ensure glass

panel is centered.

Then,usinga3/8"socket,tighten

nuts completely. HD0561

GLASS PANEL STUD

NUT

Reinstall electrical compartment cover and filters.

- 7 -

IFTHE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 7 OF THE HOOD INSTALLATION GUIDE.

IFTHE RANGE HOOD IS ALREADY INSTALLED, FOLLOW THESE STEPS:

HO0249

Remove filters by pushing them

towards the back (opposite control side)

of the hood and tilting them down. Set the

filters aside.

Carefully remove the glass panel from its packaging. Remove new glass panel nuts (factory

installed) from both studs and set aside.

IB700, IC700 AND IC700ES SERIES (CONT’D)

IS700 SERIES

- 8 -

HD0568

HD0569

FRONT GLASS PANEL STUDS LOCATION

REAR GLASS PANEL STUDS LOCATION

HD0558

GLASS PANEL

STUD

NUT

If need be, remove current

glass panel retaining nuts

from both studs. Discard

glass panel and nuts.

Insert new glass panel

studs in appropriate hood

holes.

NOTE: Install the glass

panel with the

control pictograms

on the front of the

hood.

While holding glass

panel, pre-tighten

previously removed nuts

by hand. Ensure glass

panel is centered.

Then, using a 3/8" socket,

tighten nuts completely.

Repeat steps and 

for the second glass

panel installation.

Reinstall filters.

IS700 SERIES (CONT’D)

Andere Handbücher für Connaisseure C700 SERIES

Inhaltsverzeichnis

Andere Venmar Dunstabzugshaube Handbücher

Venmar

Venmar VJ71030SS Bedienungsanleitung

Venmar

Venmar THH 1.0 Handbuch

Venmar

Venmar ESB10 Bedienungsanleitung

Venmar

Venmar Duo 1.4 Benutzerhandbuch

Venmar

Venmar FAE115 Bedienungsanleitung

Venmar

Venmar Signature S1 Series Handbuch

Venmar

Venmar VJ71130SS Bedienungsanleitung

Venmar

Venmar ISPIRA IS700 Series Bedienungsanleitung

Venmar

Venmar BISTRO VBNSA1 Series Gebrauchsanweisung

Venmar

Venmar Connaisseure C700 SERIES Bedienungsanleitung

Venmar

Venmar ISPIRA IU600ES SERIES Bedienungsanleitung

Venmar

Venmar Connaisseur CIC700 Series Bedienungsanleitung

Venmar

Venmar VBLDF1 Gebrauchsanweisung

Venmar

Venmar ISPIRA IC700 Series Bedienungsanleitung

Venmar

Venmar 1200 cfm Betriebsanleitung

Venmar

Venmar VJ603302SS Jazz Bedienungsanleitung

Venmar

Venmar BCDA Series Gebrauchsanweisung

Venmar

Venmar Bistro VBLDN1 Series Gebrauchsanweisung

Venmar

Venmar C180 SERIES Bedienungsanleitung

Venmar

Venmar VJ61030SS Handbuch

Venmar

Venmar VCQLA1 Series Gebrauchsanweisung

Venmar

Venmar CPM SERIES Bedienungsanleitung

Venmar

Venmar IK700 SERIES Bedienungsanleitung

Venmar

Venmar Chef VCQDD1 Series Gebrauchsanweisung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch