Venmar AVS S10 ERV 41700 Bedienungsanleitung

ENERGY RECOVERY VENTILATOR

Venmar AVS S10 ERV

Part no. 41700

Low speed: 50 CFM (0.2 in. w.g.), selectable 65 CFM

High speed: 100 CFM (0.4 in. w.g.), selectable 85 CFM

VB0198

CONSTRUCTION

• 22 ga. galvanized steel housing and door

• One-piece molded insulation shell,

(expanded polystyrene; UL 94 HF-1 certied)

• Galvanized steel 5" diameter ports*

• Steel door hinges and latches

• Cold side ports with plastic ring; allow vapor barrier sealing

• No drain required

*All units ports were created to be connected to ducts having a

minimum of 5” diameter, but if need be, they can be connected to

bigger sized ducts by using an appropriate transition (e.g.: 5” diameter

to 6” diameter transition).

MOTORS

• Two high reliability, external rotor PSC motors, totally enclosed and

thermally protected

• Backward blowers, can support high static pressure environment

FILTERS

• Two washable 20 ppi reticulated polyester urethane foam lters,

UL 900 class 2 certied

• Optional MERV 7 lter kit, part no.: 21030 (additional 0.1 in. w.g.

static pressure to be considered) (sold separately)

ERV CORE

• Crossow aluminum-polymerized paper core, UL723 certied

• Hydroscopic polymer exchange water by direct vapor transfer using

molecular transport without the need of condensation

• Constructed of alternate layers of corrugated aluminum material

and polymeric bactericide dessiccant impregnated media; will not

promote growth of mold or bacteria

• Unique rectangular ute design to provide very low pressure drop

values

Controls

• Integrated push-button control for Low or High speed operation.

• For a complete list of optional main and auxiliary controls available,

refer to the Wall Control Compatibility Chart on last pages of wall

controls specication sheet, available at www.venmar.ca.

• For more details about controls, refer to the Main and auxiliary wall

controls user guide, also available at www.venmar.ca.

• Removable terminal block included for quicker low voltage control

connections.

• LED indicator shows operating modes and error codes.

• Unit must be permanently energized, no control should be installed

on power supply of unit.

Air Flow

• Pressure taps and balancing chart to allow easier balancing of the

unit

• Integrated balancing/backdraft dampers in cold supply and cold

exhaust ports

Defrost Cycles

• Choice of regular or extended defrost cycles, according to climatic

conditions

• To set extended defrost cycles, refer to unit installation manual

Requirements and standards

• HVI certied

• Complies with the UL 1812 requirements regulating the installation

of Energy Recovery Ventilators

• Complies with the CSA C22.2 no. 113 Standard applicable to ventilators

• Complies with CSA C444 requirements regulating the installation of

Energy Recovery Ventilators

REGULAR DEFROST CYCLES

OUTSIDE TEMPERATURE*DEFROST IN MINUTES / AIR EXCHANGE IN MINUTES

°C °F LOW SPEED HIGH SPEED

WARMER THAN -10 WARMER THAN 14 NODEFROST NODEFROST

FROM -10 TO -15 FROM 14 TO 5 6/40 9/40

FROM -15 TO -27 FROM 5 TO -17 6/20 9/20

-27 AND LESS -17 AND LESS 8/12 11/12

Warranty

The Venmar AVS S10 ERV is protected by a 5-year warranty on parts

only, with the original proof of purchase.

* Outside temperature is read by a thermistor located inside the unit,

next to fresh air from outside port.

VENMAR AVS S10 ERV

27 /8”

22”

Ø5” TYP.

20”

9”

VK0088A

• Optional chains and springs kit (sold separately,

part no. 61239 for wood or metal construction) VD0329

VO0256

2 x

Exhaust air

to outside

Fresh air

from outside

Fresh air

to building

Exhaust air

from building

120 volts, 0.8 A

3 ft. power cord

Integrated pressure taps

for balancing

Balancing dampers,

backdraft dampers

22 ga. galvanized

steel door

HORIZONTAL INSTALLATION ONLY

32 lb.

UNIQUE 3 EASY STEPS FOR CEILING INSTALLATION







 

TOP VIEW

BOTTOM VIEW

Removable terminal block to

ease wall control connection.

Use 4-wire, 22 AWG cable

(purchase separately).

Bend integrated hooks

(2 on the same side)

and hang the unit.

Mount brackets to ceiling.

Clip the other side of

the unit to the brackets.

OR ALTERNATE INSTALLATION

• Integrated dampening device

to prevent vibration transmission

VH0104

VH0105

Example of a fully ducted installation

Example of a central draw point installation

Allow 24" x 30" minimum for access door.

ENERGY PERFORMANCE

SUPPLY

TEMPERATURE

NET AIR FLOW

POWER

CONSUMED

WATTS

SENSIBLE

RECOVERY

EFFICIENCY

APPARENT

SENSIBLE

EFFECTIVENESS

LATENT RECOVERY/

MOISTURE

TRANSFER

°C °F L/SCFMM

3/H

HEATING

03223488244 67 75 55

0 32 30 64 109 55 65 73 51

0 32 40 85 144 70 61 69 47

-25 -13 24 50 85 36 51 79 39

COOLING TOTAL RECOVERY EFFICIENCY

35 95 24 50 85 44 54

NOTE: All specications are subject to change without notice.

Coldshield™ Protection

❄❄❄❄

✹

PREVENTION MODE

(EXTRA DEFROST ADDED

TO REGULAR DEFROST)

PROTECTION MODE

(ERV UNIT SET ON EXHAUST DEFROST)

TEMPERATURE OF SUPPLIED AIR

IN DWELLING

VM0003A

NORMAL OPERATING MODE

• ERV unit is equipped with an electronic

supplemental protection to stop air

distribution in dwelling if air distribution

temperature drops below freezing point,

due to abnormal conditions.

ERV UNIT MODES BASED ON AIR DISTRIBUTION TEMPERATURE

VF0060

VF0059

VENTILATION PERFORMANCE

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1. 0

0 102030405060708090100110120130

LOW SPEEDS:

(1,2)

HIGH SPEEDS:

VG0094A

NET AIRFLOW (CFM)

EXTERNAL STATIC PRESSURE (IN. W.G.)

(3,4)

NOTE: Low speed and high speed are factory set,

low speed and high speed are selectable.

Simplied Installation (connection to a forced air system)

VJ0124

Supply-return

A + B = not less than 10 ft. (3.1 m) VJ0125

NOT Return-return!

Accoustic Noise Power Chart (dBA)

Minimum 18 in.

(0.5 m)

The data shown on left chart come from measurement performed

according to ISO 5136 Standard. These data represent the sound

power directly measured at the fresh air distribution port and

exhaust air from building port. To get the actual noise level in the

room, consider noise attenuation resulting from total ductwork

installation.

Airow Fresh air

to building port

Exhaust air

from building port

100 CFM at 0.4 in. w.g. 67.8 dBA 58.3 dBA

55 CFM at 0.1 in. w.g. 58.0 dBA 49.4 dBA

www.venmar.ca S10ERVd150407

Residential Products Group, 550 Lemire Blvd., Drummondville, Qc, Canada J2C 7W9 - Tel.: 1-800-567-3855 Fax: 1-800-567-1715

Project: REMARKS

Location:

Part no.: 41700

Qty.:

Submitted by: Date:

VENMAR AVS S10 ERV ARCHITECTURAL SPECIFICATIONS

AIRFLOW

• High static pressure backward blowers shall perform a minimum of

68 CFM @ 1.0 in. w.g.

• Optional high speed: 85 CFM

• Optional low speed: 65 CFM

CONSTRUCTION

• Housing and door shall be made of 22 ga. galvanized steel

• Insulation shall be made of one-piece molded expanded polystyrene,

UL 94 HF-1 certied

• 5" diameter ports shall be made of galvanized steel

• Door hinges and latches shall be made of steel

• Cold side ports shall have plastic ring to allow vapor barrier sealing

• Unit construction and components shall be UL and CSA certied

• Unit shall operate all year long without drain

• Weight shall not exceed 32 lb.

• Fresh air from outside and Exhaust air to outside ports shall be located

on same side

• Backdraft dampers shall be integrated in cold supply and cold

exhaust port

• ERV unit shall be HVI certied

MOTORS

• Unit shall have two high reliability, external rotor PSC motors, totally

enclosed and thermally protected

• The backward blowers shall support high static pressure environment

• The insulation class shall be B

FILTERS

• ERV unit shall have two washable 20 ppi reticulated polyester

urethane foam lters, UL 900 class 2 certied

• Optional MERV 7 lter kit shall be available, part no.: 21030

ERV CORE

• The ERV core shall be a crossow aluminum-polymerized paper core,

UL723 certied

• Hydroscopicpolymerexchangewaterbydirectvaportransfershalluse

molecular transport without the need of condensation

• The ERV core shall be constructed of alternate layers of corrugated

aluminum material and polymeric bactericide dessiccant

impregnated media; and shall not promote growth of mold or bacteria

• The ERV core design shall be made of rectangular utes to provide

very low pressure drop values

Controls

• Unit shall be equipped with an integrated push-button control for

Low or High speed operation

• Choice of low voltage main controls (not included) shall be

energized by ERV unit

• Optional low voltage auxiliary controls (not included) shall be

energized by ERV unit

• Removable terminal block shall be included for quicker low voltage

control connections

• A LED indicator shall indicate operating modes as well as error codes

• ERV unit shall be permanently energized, no control shall be installed

on power supply of unit

Air Flow Balancing

• Unit door shall be equipped with pressure taps as well as a

balancing chart to allow verication of balancing of the ERV unit

• Balancing dampers shall be integrated in cold supply and cold

exhaust ports

Defrost Cycles

• Unit operation shall include a choice of regular or extended defrost

cycles, according to climatic conditions

• Unit shall be equipped with Coldshield™ protection to stop air supply

in dwelling if air supply temperature drops below freezing point, due

to abnormal conditions.

Accoustic Noise Power

• The unit shall have a maximum acoustic noise power of 58.0 dBA

on low speed at 0.1 in. w.g. and 67.8 dBA on high speed at 0.4 in. w.g.,

measured at fresh air to building port.

• The unit shall have a maximum acoustic noise power of 49.4 dBA

on low speed at 0.1 in. w.g. and 58.3 dBA on high speed at 0.4 in. w.g.,

measured at exhaust air from building port.

Requirements and standards

• Shall be HVI certied as per CSA C439 Standards

• Shall comply with the UL 1812 requirements regulating

the installation of Energy Recovery Ventilators

• Shall comply with the CSA C22.2 no. 113 Standard

applicable to ventilators

• Shall comply with CSA C444 requirements regulating

the installation of Energy Recovery Ventilators

Warranty

Unit shall be protected by a 5-year warranty on parts only, with the

original proof of purchase.

Andere Venmar Belüftung Handbücher

Venmar

Venmar Solo 1.5 Benutzerhandbuch

Beliebte Belüftung Handbücher anderer Marken

Pichler

Pichler Ventech LG 150 Bedienungsanleitung

Hitachi

Hitachi RAF-50RPA Bedienungsanleitung

Daikin

Daikin FWF02B7TV1B Bedienungsanleitung

Paul

Paul santos 570 DC Bedienungsanleitung

Meltem

Meltem M-WRG-K Bedienungsanleitung

nilan

nilan Compact P Bedienungsanleitung

Whalen

Whalen VW series Montageanleitung

marinco

marinco N20803W Bedienungsanleitung

Xpelair

Xpelair Xplus2 EC RFH Bedienungsanleitung

Vents

Vents Micra 60 Bedienungsanleitung

Broan

Broan XB110H Bedienungsanleitung

Fantech

Fantech VHR704R Bedienungsanleitung

DewStop

DewStop Breeze Easy Bedienungsanleitung

DuraVent

DuraVent DCL Bedienungsanleitung

Broan

Broan HRVH100SE Bedienungsanleitung

Trane

Trane GGAA Montage- und Bedienungsanleitung

Miele

Miele AWG 102 Bedienungsanleitung

ClimaRad

ClimaRad BV Bedienungsanleitung