VENOM V540 Bedienungsanleitung
1/16th
Hex
Screws
Motor HousingTiming Plate
Sensor
Port
Bearings
Output
Shaft
and
Magnet
Housing
Sleeve
Bottom Plate
COUNTERCLOCKWISE / CLOCKWISE
1/16th
Hex
Screws
TIMING
The timing on the Venom™ V540 brushless motor is
extremely easy to adjust. You will need to loosen the
three 1/16th hex screws that are located at the top of the
motor near the Sensor Cable Port. Grip the top and turn
clockwise to advance the timing. (This adjustment
applies when output shaft is set to turn counter clock-
wise). The opposite is true to delay/retard timing. The
rotation direction of the motor can be changed by
switching any two of the three power wires. The effect of
advancing the timing is to make slightly more power
from the motor. The down side is increased heat and
less run time. There is a balance to be found in adjusting
the timing this is just one more tool in finding the balance
for your set up. Note: if the motor is run in a counter
clockwise direction the timing advance will be
clockwise.
Disassembling the Motor:
1) Remove all three Hex screws at the bottom of the motor
with a 1/16th hex screw driver.
2) Remove the bottom plate from the Motor Housing.
Remove or oil the bearing located in the plate where the
out-put shaft has been removed.
3) Carefully remove the Output Shaft and Magnet.
4) Remove three smaller hex screws from the top of the
Timing Plate.
5) Remove Sensor Port buy turning it clockwise and lifting
out of the Motor Housing hole.
6) Located inside the Sensor Port slot inside the Motor
Housing is the 2nd bearing to be oiled or removed.
DISASSEMBLED
NOTE: This is the manufacturer default setting
• Never leave the motor unattended while it is ON or plugged
in. If the motor overheats there is the potential for fire.
• Always check the connections of the wires and cables to
ensure correct polarity.
• Make sure all wires and cables are well insulated to
avoid short circuiting.
• Avoid contact with water and any other liquids. If this
occurs, stop the use of the product and set out to dry.
• Never solder on the PCB or other components.
• DO NOT over tighten the hex screws, this may lead
to stripping them. Warranty does not cover the screws.
• Check to make sure you have the correct gear ratio
and never overload the motor.
• DO NOT APPLY FULL THROTTLE if the motor has not
been installed. The high RPM of these motor can possibly
damage them.
• Make sure all connections and screws have been fastened
to avoid an out of control model.
• Always use a high power soldering unit and avoid
prolonged soldering to avoid damage to the different
components of the motor.
INSTALLATION
Thank you for purchasing the Venom™ V540 Brushless
Motor. This motor was designed for power and performance
thanks to it’s well ventilated can and sensor capabilities. This
Motor has bearings that are serviceable and a replaceable
rotor.
Sensor Cable VEN-1356 (Sold Separately):
A Bi-Directional Sensor Cable must be used with the V540
Motor at all times or else the motor will not work. Plug the
Sensor Cable into the Motor Sensor Cable Port and also into
the desired ESC (Speed control). (Refer to PART KEY
Drawing below)
Power Wires: To connect the correct power wires that will
provide power to the Venom™ V540, they will need to be
soldered accordingly. (Refer to PART KEY Drawing below)
1) Install the V540 into the model
2) Connect the Sensor Cable to both the Venom™ V540
Motor and the desired ESC.
3) Connect the Orange, Yellow, Blue Power Wires to the
ESC. NOTE: Check for correct polarity to avoid
damaging the Motor and the ESC.
4) Make sure all connections are correct before running the
model.
PART KEY
WARNING
Soldiering Tabs
Output Shaft
VEN-1356 Sensor Cable
Orange
Sensor
Cable
Port
Yellow ESC
Speed
Control
Blue
TOP
BOTTOM
(Sold Separately)
VEN-1325
3.5T
VEN-1326
4.5T
VEN-1327
5.5T
VEN-1328
6.5T
VEN-1329
7.5T
VEN-1330
8.5T
VEN-1331
9.5T
VEN-1333
13.5T
V540
BL Motor
IFMAR
Spec
NORMAL
VOLTS
VOLTS
RANGE
KV
Max.Efficien.
Amps 7.2v
Max. power
Amps 7.2v
Max. power
(W) @ 7.2v
Max. power
(W) @ 6v
Max. power
(W) @ 4.8v
Max.
Length
Max.
Can Length
Max.
Dia.
Weight
Integraded
Cooling Fan
Recommended
Gear Box
Configurations
w/ 6 cells
YES
YES YES YES YES YES YESYESYESYESYES
6v
4.8 - 7.4
10200
76A
130A
550W
400W
305W
70mm
52.5
35.8
156g 156g156g156g156g156g156g156g156g156g156g
Comparable
Stock Motor 19T 21T 23T 27T
1:10 TC
1:8.5 - 1:12
1:10 TC
1:7 - 1:10
4WD
1:13.5 - 1:15
1:10 TC
1:6 - 1:9
2WD Truck
1:12 - 1:13.5
1:10 TC
1:5 - 1:7.5
2WD, Truck
1:10.5 - 1:13
1:10 TC
1:4 - 1:6
Off-Road
1:7.5 - 1:10
1:10 TC
1:4 - 1:6
Off-Road
1:7.5 - 1:10
1/10 EP
Touring
1:6.8-1:8
1/10 On
Road
1:5-1:6.8
1/10 On
Road
1:5-1:6
Off Road
35.8 35.8 35.8 35.8 35.8 35.8 35.8 35.835.8
52.5 52.5 52.5 52.5 52.5 52.5 52.5 52.552.5
70mm 70mm 70mm 70mm 70mm 70mm 70mm 70mm70mm
275W 225W 200W 180W 145W 130W 120W 105W 80W
360W 300W 270W 200W 175W 160W 160W 145W 115W
480W 390W 350W 310W 250W 230W 210W 185W 140W
120A 95A 85A 75A 60A 55A 50A 45A 35A
67A 54A 49A 43A 35A 32A 29A 26A 19A
8500 7000 6200 5500 4600 4400 4000 3200 2400
4.8 - 7.4 4.8 - 7.4 4.8 - 7.4 4.8 - 7.4 4.8 - 7.4 4.8 - 7.4 4.8 - 7.4 4.8 - 7.44.8 - 7.4
7.2v 7.2v 7.2v 7.2v 7.2v 7.2v 7.2v 7.2v7.2v
YES YES YES YES YES YES YES YESYES
VEN-1332
10.5T
VEN-1338
17.5T
YES
55T
1/10
Rock-
Crawler
35.8
52.5
70mm
65W
90W
100W
30A
14A
2200
4.8 - 7.4
7.2v
YES
VEN-1334
18.5T
Venom Group International
600 West Buckles Rd.
Hayden, ID 83835
Customer Service
800.705.0620
Australia
PO Box 7325
Alexandria NSW 2015
Australia
Venom™ Limited Warranty
CONTACT INFO
Venom™ GUARANTEE
The V540 Brushless Motor is a unique brushless design
that will need to be geared differently than any other
brushed motor. It is very important that the gear ratio
recommendations are correct. Over gearing your V540
Brushless Motor may result in overheating and the
unexpected shutdown of the ESC. Each R/C model
should have this information inside of the manual that it
came with.
GEARING
Guarantee
We guarantee this product to be free of manufacturing
faults and material defects. This product has been
checked and adjusted individually before leaving the
manufacturer. Please contact your local hobby shop for
replacement parts and technical support or contact
Venom™ Customer Service at 800.705.0620 or
Notice of Rights
All rights reserved. No part of these instructions may be
reproduced or transmitted in any form by any means,
electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of
Venom™. For information on getting permission for
reprints and excerpts, contact:
Notice of Liability
The information in these instructions is distributed on
an “As Is” basis, without warranty. While every
precaution has been taken in the preparation of these
Instructions Venom™ does not have any liability to any
person or entity with respect to any loss or damage
caused or alleged to be caused directly or indirectly by
the information contained in these or by the products
described in it.
Venom™ warrants this product to be free of material
and workmanship defects when new. If a component is
defective or was not correctly made, Venom™ will, at its
sole discretion, repair or replace it free of charge within
90 days from date of purchase. If you believe a defect
became evident only after operation, please contact us
to discuss the situation.
A dated & itemized sales receipt must accompany any
product returned for warranty work. Before returning
any product, please contact Venom™ Customer
Service at 800-705-0620 to receive a Return
Merchandise Authorization Number (RMA#).
SPEC GUIDE
© Copyright 2008 Venom Group International
Andere VENOM Motor Handbücher
